← VBar NEO/EVO VLink

Wren44 heli, Neo, Neo-Nitro-Governor - shutdown in flight translated

VBar › VBar NEO/EVO VLink · Started by nurmalso on 2 November 2019 19:3502.11.2019 19:35
nurmalso 2 November 2019 19:3502.11.2019 19:35
Moin,

ich versuche, meinen T-Rex mit Wren44 mit der Neo, dem internen Drehzahlregler und Hallsensor mit 1 aktivem Magnet auf der Kupplung zu fliegen.

Mittlerweile hatte ich 3 Absteller im Flug und suche noch immer die Ursache für die 2 letzten.

Den ersten habe ich aussortiert, Basisgas stand auf 0. Ich unterstelle, dass der Neo-Regler dann beim Entlasten des Rotors das Gas zurücknehmen wollte und dann eben Throttle 0 gesendet hat... Turbine aus... Autorotation, alles ok...

Das ganze Setup neu gemacht. Die Wege der TurbinenEcu neu bei gebogen.

Setup ist so:
Sicherheitsschalter AUS: Throttle 0
Sicherheitsschalter AN, Motorschalter AUS, throttle 7% (idle)
Sicherheitsschalter AN, Motorschalter AN, throttle 7% (idle) hier dreht die Turbine schon 20.000 UPM hoch, obwohl sich der an der GSU angezeigte Throttle Wert NICHT ändert. Seltsam aber ok.

Sicherheitsschalter AN, Motorschalter AN, Direktgas zum Hochlaufen in Bank 1, dann Umschalten auf Bank 2, Drehzahlvorgabe 1700 - das passt.
Da ich den Heckoptimierer laufen lassen wollte, hab ich auf Bank 2 umgeschaltet, Drehzahl 1900. Dann eine Pirouette, gestoppt, etwas nach gewippt und Turbine AUS. Autorotation.... hmmm

Nun bin ich auf der Suche... in der Ecu wird nur alle 5 Sekunden gelogged, ich kann da nicht wirklich nach vollziehen, ob das Stabi mir wieder die Turbine abgestellt hat... Heck entlastet, Drehzahl steigt, nachregeln... kann das sein? Kann das Neo bei aktiver Regelung Throttle Werte unter Basisgas ausgeben? In meinem Fall ist alles unter 5% Gas ein Absteller.

Einzig auffällig im Log ist, kurz vor dem Absteller, ein "Signal vom Drehzahlsensor fehlt" Eintrag.
Ich häng mal das Log und das Setup aus der Neo an. Bin aktuell etwas ratlos.

Hat meine ECU womöglich 'n Schuss oder stellt mir die Neo die Bine ab..... Und ich will einfach nicht mit Gaskurve fliegen aber das wäre der nächste Versuch... macht bei dem Wetter keinen Spass, Fehler zu suchen...

In Trockenübungen passen die Gaswerte, bloss ist das ohne aktive Regelung, sprich Turbine aus oder auch Heli ohne Blätter am Boden alles witzlos, da funktioniert alles.

Nunja... vielleicht hab ich den Nitro Regler noch nicht verstanden oder des fehlenden Drehzahlsignals wird abgestellt oder oder oder meine Ecu hat doch n Schuss... Ich weiss nicht weiter.

Grüße
Markus
| - neo-t-rex-wren.zip (538 bytes)
RV 2 November 2019 19:5802.11.2019 19:58
Baue einen Temperatursensor von uns auf TELE1 ein, lade die App dazu. Damit hast Du dann (VBC-t vorausgesetzt) ein grafisches Log mit Gaswert, RPM und Aussentemperatur ;-)

Generell geht der Regler nur bis Min Limit runter wenn er einmal darüber "aktiv" ist.
Bei Ausfall RPM Signal (einfach mal ein Servo statt ECU dran und ohne RPM Siglan ansehen) geht er mit der Gaskurve die sich aus Basisgas und Pitch Zugabe zusammensetzt.

Wie sind denn die Werte Min Limit und Basisgas?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nurmalso 2 November 2019 20:1902.11.2019 20:19
Basisgas in Bank 2 und 3 ist 40
Gasminimum 7, AR Gas 5

Das mit dem Temp Sensor ist 'ne Idee. Stromsensor ginge ja auch, Turbinenakku überwachen macht mehr Sinn, als die Aussentemperatur... :-)
Edith sagt: Der Temp Sensor kostet die Hälfte, hab gerade mal einen bestellt.



1 mal bearbeitet. Zuletzt am 02.11.2019 20:21 von nurmalso.
RV 2 November 2019 22:4002.11.2019 22:40
Quote:Gasminimum 7, AR Gas 5


Und Du bist sicher dass sie da nicht schon aus ist? Getestet? Auch beim abrupten Gasgeben dann? Nicht dass sie sich verschluckt beim "reinlangen" nach einer Entlastungsphase wenns zuvor bis aufs Min Limit runterging ...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 02.11.2019 22:40 von RV.
nurmalso 3 November 2019 07:3003.11.2019 07:30
Good morning,

Yes, that's been tested. As far as I understand the nitro controller, the minimum throttle is active when the engine is supposed to be idling. So, the "Min Limit," which isn't represented as a value in the Touch app. It can only be the minimum throttle.

AR GAS is somehow different again; if it's higher than 5, the turbine doesn't go into idle, so I ran it without blades, let Bank 2 regulate, pulled AR, and turned the value down until idle was reached (it was previously at 20).

I'm afraid that until I have the temperature sensor, I won't be able to figure out what's causing the shutdown. Whether it's the ECU or the Neo.

Perhaps the pump is defective, but so far everything points to a control issue, as the turbine demonstrably shuts down when the load on the rotor/tail rotor changes drastically, specifically towards reduced load. This isn't noticeable on the ground, as only the tail rotor is active there, resulting in very little load on the system.

If the weather is good today, I'll continue testing...
machine-translated from German · Show original
nurmalso 3 November 2019 07:3203.11.2019 07:32
Just to clarify, what does the NEO do when the RPM signal is missing? I've seen a few log entries like that... I do have a throttle curve configured via macro cells, but it's not active in banks 2 and 3, since I want to fly using the control system.
machine-translated from German · Show original
RV 3 November 2019 10:4903.11.2019 10:49
Quote:Ich hab zwar 'ne Gaskurve über Makrozellen hinterlegt aber die ist ja nicht aktiv in Bank 2 und 3, da ich über die Regelung fliegen will.

FALSCH!

Die Gaskurve ist immer da ... denn eine reine Regelung kann immer erst REGELN wenn sie eine REGELABWEICHUNG erkennt, hinkt also hinterher (z.B. E-Regler in "ihrem" eigenen Modus).

Vergleich: Du willst mit konstant 100km/h Auto fahren, siehst nur den Tacho und nicht draussen die Berge und Täler kommen ...

Nimmt man eine Gaskurve als Vorsteuerung (nicht schwingfähig, sofort da) - ist das ganze viel besser gestützt. Die Regelung liegt dann da "drüber".

Vergleich: Du willst mit konstant 100km/h Auto fahren, siehst den Tacho und draussen die Berge und Täler kommen ...


Und genau das macht der VBar Governor. Egal ob E- oder Nitro Modus.

Fallback - bei Ausfall RPM Signal IST dann die Gaskurve dahinter da die Reglung nun nicht mehr regeln kann. Hat mir an der BO105 schonmal den A... gerettet.

Hast Du das denn schon wie empfohlen mit einem Servo probiert? - ich schreibe das jedes Mal weil das soooo schwer zu glauben ist für die Jungs da draussen ... und keiner tuts ;-(

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV 3 November 2019 10:5503.11.2019 10:55
Quote:Gasminimum aktiv, wenn der Motor idlen soll. Also das "Min Limit", welches sich als so bezeichneter Wert in der Touch nicht wieder findet. Kann ja nur Gasminimum sein.

Idle = LEERlauf = SEPARAT einzustellen

Gasminimum = Min Limit = UNTERE REGELGRENZE im geregelten (!!!) Betrieb - soll z.B. Absterben bei massiver Entlastung und Overspeed verhindern und auch den Motor etwas auf "Laune" halten für den Abfangpunch dann. Denn LL (Idle) wäre zu wenig als Ausgang für ein schnelles Abfangen.

Du solltest ggf. das hier mal genau studieren, da sind die Zusammenhänge drin:

https://www.vstabi.info/de/node/2032

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV 3 November 2019 10:5603.11.2019 10:56
Quote:wenn sich der Lastzustand des Rotors/Heckrotors massiv ändert und zwar in Richtung Entlastung.

Das hatte ich hier schon befürchtet aufgrund der Werte:

Quote:Quote:
Gasminimum 7, AR Gas 5


Und Du bist sicher dass sie da nicht schon aus ist? Getestet? Auch beim abrupten Gasgeben dann? Nicht dass sie sich verschluckt beim "reinlangen" nach einer Entlastungsphase wenns zuvor bis aufs Min Limit runterging ...

Setze das Gasmin mal auf 20 oder so - das sollte safe sein. Es muss aber so nieder sein dass er beim Spoolup mit Nullpitch und Regelungswunsch da dann leicht drüber ist - sonst regelt er logischerweise nie ein.

Wie ist denn die gaskurve nun und das Gain jeweils?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




2 mal bearbeitet. Zuletzt am 03.11.2019 11:04 von RV.
nurmalso 3 November 2019 12:1303.11.2019 12:13
I had roughly set a "special gas curve" in banks 2 and 3 via the macro cells, but then I installed the sensor and switched back to the governor, which deactivated the "special gas curve".

Yesterday, when I wanted to test with the gas curve, I reactivated it in bank 2, where a diagonal standard curve was already stored. Since I didn't feel like setting it up again, I abandoned the test and deactivated it again.

Therefore, no gas curve has been entered by ME; only the standard curve from the Gov can be included, whatever you conjure up from the set values.

Until recently I had a Nitro Rex with Neo Gov, the settings were roughly similar, so the servo thing doesn't help me much, as I can't simulate what happens during the control process.

I'll probably have to wait for the temperature sensor to arrive so I can study the log to see exactly what's happening. It's possible the ECU or pump is acting up, and I'm looking in the wrong place. After all, everything works as expected on the ground, but tests without the main rotor blades aren't the same... significantly less pump voltage corresponding to the desired RPM.

I'll test again later on the field with different minimum values. I've already studied the page you linked to exhaustively and, in my opinion, I understand it. That makes the shutdowns even less understandable, because in my opinion, the controller shouldn't output 0% throttle, and 5% is safe, as the engine "shouldn't" shut off then... Who knows what the problem is.

The problem might be that, according to the linked page, IDLE is BELOW 0% of the throttle curve, but 0% on this engine is "trim down, stick down" and therefore engine OFF. I NEED to be a few percent ahead to program "stick down trim UP", which then represents IDLE and readiness to start.
I managed to get all of that working. The only question now is whether the governor, in active control mode, has the option to output values BELOW this magic 5% as a gas target.
I can't test that in a dry environment, with a servo at the output.
The problems only arise in flight, not when testing the system on the ground.

Therefore, I'm afraid we're talking at cross purposes. The Wren isn't a jetcat where you fly with a linear throttle curve or a fixed value like 100%. That's simply not possible with the Wren.

It needs a control system like a nitro booster, a V-curve or governor. Since a curve seems like something from the Stone Age to me... well...

Perhaps we should go through the whole thing on the phone; maybe I'm overcomplicating things at some point.
machine-translated from German · Show original
nurmalso 3 November 2019 12:1603.11.2019 12:16
In bank 1, I've programmed a curve to even get above 0% throttle with the stick down. I simply can't send or teach the ECU a throttle value below 0% for the engine to be off.
machine-translated from German · Show original
RV 3 November 2019 14:0903.11.2019 14:09
Quote:Es ist also von MIR keine Gaskurve hinterlegt, da kann nur die Standardkurve vom Gov drin sein, was auch immer Ihr da aus den eingestellten Werten zaubert.

Siehe den verlinkten Artikel und die Diagramme samt Beschriftungen dort. Der Gaswert resulitiert aus Basisgas Plus Zugaben (vornehmlich Pitch Zugabe).

Quote:Ich hatte bis vor kurzem n Nitro Rex mit Neo Gov, da war die Einstellung in etwa ähnlich, das mit dem Servo bringt mich also so nicht weiter, da ich so nicht simulieren kann, was während der Regelung passiert.

Das war so gemeit dass Du es glaubst dass die Gaskurve aktiv ist auch wenn kein RPM kommt.


Das mit der Ausgabe an die Turbnine ist mir schon klar - denn Pahl machts nicht anders - und da gehts. Allerdings ist das ein Scaler mit seehhhrrr dezenter Gaskurve und wenig Empfindlichkeiten - die 2-Wellen Turbinen sind halt da noch mit der Folgsamkeit der Luftkupplung und dazwischen.

Wir reglen den Gasgenerator ja mit der RPM der Leistungsstufe als Regelgröße. Sollte nun z.B. viel Punch gefordert sein und der Generator schnell hochdreht - die Leistungsstufe aber grad "bremst" und nicht so schnell beschleunigen kann - entsteht möglicherweise ein Gasstau ... Rückstau .... Aus.


Quote: Sie braucht eine Regelung wie ein Nitro, eben V-Kurve oder Governer. Da eine Kurve für mich aus der Steinzeit kommt... naja...

Die Kurve ist, mein Lieber die beste Regelung da sie nie hinterherhinkt. Ist bei jedem Nitro immer noch so. Bei Elektro mit VGov ist sie auch da - deswegen sind die Teile spritziger als ein hinterherhechelnder Regler.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




2 mal bearbeitet. Zuletzt am 03.11.2019 14:13 von RV.
nurmalso 3 November 2019 14:2903.11.2019 14:29
Okay, since the base gas level is at 40, the governor cannot possibly shut down the turbine on his own.

And a stop from a pirouette should not generate so much load that it results in a gas jam or forced shutdown.

I'm waiting for the temperature sensor and am probably looking for the fault in the pump or ECU.

Thanks first of all, Rainer.
machine-translated from German · Show original
RV 3 November 2019 14:5803.11.2019 14:58
Quote:Ok, da Basisgas auf 40 steht, kann der Governer allein die Turbine unmöglich abstellen.

Wenn RPM ausfällt - hast Du mit Deiner Betrachtung recht da keine Regelung da ist.

Wenn Regelung aktiv (RPM liegt an, IST über 600 1/min und Gasminimum ist überschritten) kann das Gas dann geregelt über den P Anteil bis Gasminimum heruntergehen wenn z.B. die Ist RPM wesentlich über der Soll RPM liegt (Overspeed, schneller Sinkflug). Ist dann das Gasminimum nicht "safe" genug ...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 03.11.2019 14:58 von RV.
nurmalso 3 November 2019 15:3803.11.2019 15:38
I've just set the minimum gas temperature to 30; the base gas temperature is 40.

Same test as yesterday, head speed regulated to 1900

A little pitch pump, no problem

A pirouette with active tail optimizer, short after-oscillation - off

I'm now finally waiting for the temperature sensor to provide a proper log.
The log from the ECU is useless; it only saves values every 5 seconds.
machine-translated from German · Show original
nurmalso 3 November 2019 16:3803.11.2019 16:38
So.
A fellow pilot had a shutdown due to the maximum throttle value... the transmitter was sending more throttle than programmed when the stick was at maximum.

My government had a maximum value of 100, of course.

However, the transmitter only outputs 99% when the stick is in the up position; 100% only if you push against the mechanical resistance.

Thus, 99 is stored as full throttle in the ECU.

After the pirouette, the governor, perhaps aided by the inertia of the turbine, requested 100% power and reproducibly shut it down. The ECU doesn't like that.

Full throttle reduced to 95 in the governor... problem solved. No more stalling so far. Now just a little fine-tuning and everything will be good.

Thanks for the support here! As far as I know, no other manufacturer offers this.

Have a beautiful Sunday
machine-translated from German · Show original
RV 3 November 2019 18:2503.11.2019 18:25
Ahhh - Super Sache, das muss man aber auch wissen.
Ist so wie die kraftlosen Servos wenn der Puls zu lang wird (gab mal lustige Figuren...) ;-)

Danke für die Blumen, berichte dann bitte mal wie sich das Teil so fliegt, was Du fliegst und wie das regelt. Vor allem dann bitte mit Grafik ;-)

BTW ... wäre nicht das ne Option dazu:

https://www.vstabi.info/de/node/2296

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nurmalso 3 November 2019 18:5403.11.2019 18:54
>
> By the way... wouldn't that be an option?
>
> https://www.vstabi.info/de/node/2296

I thought about it, but since the tank is perfectly visible, just like on the Nitro T-Rex, I discarded the idea. An additional Neo, more hoses, more cables... It would probably fit somehow, but it's overkill for that helicopter.

The temperature sensor is being installed, precisely for logging purposes. I think the Neo could write this log by default; the RC voltage is always present, and the RPM sensor is already there, as is the throttle position sensor.

I'll gladly upload a video now and then. For me, it's limited to fast circuits with loops, rolls, and sharp figure eights (I love the sound of the blades rattling, even if it's mechanically unhealthy). I certainly won't be pushing this heli as hard as the 800-size one, but ultimately it's a 5kW heli with a 6.5 kg takeoff weight, so it can do quite a bit.

As far as the rules are concerned, I have no doubts, I will mainly play with gain and pitch adjustment.

The soundscape of the helicopter is fantastic, considerably more pleasant and quieter than the PHT-3.

Well then.
machine-translated from German · Show original
nurmalso 11 November 2019 11:2911.11.2019 11:29
Good morning,

So, I'm still testing, but the first logs are in. I can now probably rule out the stabilizer as the cause of the shutdown. (The temperature sensor isn't available, so I'm now "monitoring" the turbine battery...)


Feel free to browse my cloud; the first rule results are there.

Flights yesterday with the "T-Rex Wren44"

At 12:29 there was a hovering flight for noise measurement, set to 1900 RPM with a gain of 2, sensitivity 40, pitch addition 20, cyclic 20

At 1:06 PM, an attempt was made to reproduce the stalling. A pirouette using the torque caused the rear end to stop, resulting in the stall. Unfortunately, the flight graph is not displayed in the cloud. Deleting and re-uploading it from the Touch (archive bit set) unfortunately does not resolve the issue.

13:47, same attempt, as expected with the same result. Hovering, 3 meters high, 1 pirouette, shutdown.

14:23, test with "special throttle curve active" in bank 2, 1700 RPM is set as the speed target in the controller. Until then, I didn't know that the controller remained active. We increased the throttle curve further because 1700 RPM was too low. No change in RPM.

Here's a question: how can I tell Nitrogov to use the throttle curve in Bank 2, for example, without any regulation?


Regarding my search for the cause of the problem... there's no air in the lines. I have a hopper tank and the tubing is new. I'm kind of groping in the dark here. My suspicion is now pointing towards the pump and/or valves and/or a loose connection in the wiring harness. BUT the fact that it's reproducible with the pirouette is really annoying me. I haven't tried any other maneuvers yet (understandably). The stabilizer isn't fully adjusted. How could it be if I can't fly properly? :-)

However, the acceleration and deceleration values (in the ECU) were set very low by the previous owner. I increased them to the highest recommended setting according to the manual, from 7 and 8 respectively, to 15 each.
It might be coming from there. Unfortunately, I can't test it until next weekend, and only if the weather's good. It's no fun in this cold.



Edited once. Last edited on 11/11/2019 at 11:32 by nurmalso.
machine-translated from German · Show original
RV 11 November 2019 15:1011.11.2019 15:10
Quote:Hier nun mal eine Frage, wie kann ich dem Nitrogov sagen, dass er beispielsweise in Bank 2 gefälligst die Gaskurve verwenden soll, ohne Regelung?

Integral und Empfindlichkeit auf 0 ;-)


Wegen der Absteller - wie war das mit dem Vollgaswert? Hat das nix gebracht den 5 Punkte abzusenken? Wie hoch ist denn die untere Regelgrenze (min.Limit) jetzt? - Weil diese 2 Werte sind die Endwerte die es im Flug geben kann. Wie schnell die zum Tragen kommen bestimmt man über die Empfindlichkeiten (ev noch zu viel P oder gar D).

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nurmalso 11 November 2019 18:3011.11.2019 18:30
As far as I can see, the stabilizer isn't the component that tells the turbine to shut down. Incidentally, it was strange that the FULL THROTTLE value entered in the Nitrogov setup was 95 (just 5 points down), yet a maximum value of 97% was still being transmitted. However, this wasn't from the ESC but from the direct throttle bank 1 throttle curve. Since this was set before takeoff, it's irrelevant to the shutdown issue.

After the next shutdown, I absolutely must connect the data terminal to the ECU and read out the reason for the last shutdown. The only problem is that it doesn't cool down when the engine shuts down, and it can't be cooled via USB stick either.

So, fly without the canopy, quickly read the error codes, and then restart immediately... Unfortunately, I can't access the second-to-last reason for the shutdown.
That shouldn't be your concern at all. But I have enough food for thought to help you sort it out.

Gas minimum 30
Base gas in banks 2 and 3, 40 each
Idle speed 20
AR Gas 20
Ramp-up limit 2 (so quite slow) <- only comes into play during active control when switching banks, right?) How quickly the controller changes the throttle value is determined solely by the sensitivity.

Ultimately, the ECU has to cope with a change in throttle value from 20 to 100 and "translate" it according to its own parameters. That's where the acceleration limit comes into play... another indication that the stabilizer isn't shutting it down; it's not cooling. So it must be a shutdown due to a fault. I would look for failsafes in the transmitter. A loose connection in the throttle cable could also be a possibility.

BUT then the issue of reproducibility comes up again.

I'm going in circles and I won't have time again until Sunday. It's enough to make you cry.



Edited once. Last edited on 11/11/2019 at 18:31 by nurmalso.
machine-translated from German · Show original
nurmalso 11 November 2019 19:0211.11.2019 19:02
I have one more question...

A stop from a pirouette using torque would introduce load into the system and thus reduce the rotational speed.
How quickly does the stability control system regulate this, and would a full throttle request be visible in the log in every case, or could it be repeatedly lost due to the log's latency?

Unlikely, right? I'm currently writing an email to Wren to get a hot tip from them on where I should continue my search.

It can't be that it repeatedly shuts down during a simple pirouette. Then the helicopter is practically unflyable.
machine-translated from German · Show original
JMalberg 11 November 2019 21:4211.11.2019 21:42
Would the old-school method using a parallel servo for display be helpful?

Connect a servo to the throttle output on the Wren using a Y-cable. Attach a colorful, four-segment disc to the servo and position the servo so the disc is clearly visible.
Then you test the behavior of the throttle output without the Ltd Wren, and later in flight you check whether the servo behaves according to your Wren.
Here you can see if too much gas is being added during pirouette stops.

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
machine-translated from German · Show original
nurmalso 11 November 2019 22:0311.11.2019 22:03
Hi Jürgen,

Cool idea, the servo in addition to the ECU. It doesn't make sense without Mr. Wren. On the ground, everything works as it should, and in operation without blades, it works fine too. But in the air, under load, other things come into play. That's where the servo comes in handy.
Let's see what the English say. I hope I've got this done before Brexit...


Greetings
Markus
machine-translated from German · Show original
RV 11 November 2019 23:3711.11.2019 23:37
Quote:würde man eine GASANFORDERUNG von VOLLGAS im Log in JEDEM Fall sehen oder kann das unter Umständen - widerholbar - von der Latenz des Logs verschluckt werden?

Der Graph läuft nur langsam, d.h. es könnte sein dass es da nicht in voller Ausprägung zu sehen ist - die Regelung macht ja die Stabi an sich selbst. Allerdings sollte man da dann doch eine Tendenz erkennen.

Aber ... mit weniger Empfindlichkeit der Governor Regelung sollte das aber schon dann wirken. Stell da mal nur 20 statt 40 ein.

Wenn es beim Heckstop ist - Du kannst mit der Heckbeschleunigung (35 mal einstellen, je weniger desto weicher) auch die Heckreaktionshärte entschärfen ;-) - Das hätte auch Auswirkungen auf RPM, klar ...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 11.11.2019 23:38 von RV.
VStabi VStabi Pioneer of Flybarless