rutra
2 May 2025 16:2602.05.2025 16:26
Hello, I bought a VBar RX-Only, 7-channel receiver for practice. I want to program a fixed-wing model with the following functions.
ESC = Motor
CH1 = Altitude
CH2 = Left Aileron
CH3 = Right Aileron
CH4/AUX1 = Left flap
CH5/Tail = Side
CH6/AUX2 = Right flap
Is this channel order correct?
Everything is going well so far, except I can't get the flaps to work... I'm completely stumped.
Edited 1 time(s). Last edit at 05/03/2025 09:41AM by rutra.
Hallo, habe mir zum Üben mal einen VStabi RX-Only, 7-Kanal Empfänger gekauft. Ich möchte ein Flächenmodell mit folgenden Funktionen programmieren.
ESC = Motor
CH1 = Höhe
CH2 = Querruder Links
CH3 = Querruder Rechts
CH4/AUX1 = Klappe links
CH5/Tail = Seite
CH6/AUX2 = Klappe rechts
Ist diese Kanalreihenfolge richtig?
Es geht soweit alles gut nur die Klappen bekomme ich nicht zum laufen.....stehe irgendwie auf dem Schlauch.
Edited 1 time(s). Last edit at 05/03/2025 09:41AM by rutra.
RV
3 May 2025 11:3503.05.2025 11:35
In short:
MC27 is a 3-level control with switches and position indicators for the flaps - please only use ONE direction, not from + to - and vice versa.
MC9 is a channel with delay
In the wing mixer, expert %-e flaps are screwed in.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 05/03/2025 11:36AM by RV.
Klappen in Kurzform:
MC27 ist 3-Level mit Schlater und Pos der Klappen - bitte nur EINE Richtung, nicht von + nach - und umgekehrt
MC9 ist Kanal mit Delay
In dem Wingmixern, Expert %-e Klapen eindrehen
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 05/03/2025 11:36AM by RV.
rutra
3 May 2025 16:1603.05.2025 16:16
Hello, how do I assign what and where?
In the Model Setup menu:
-Output Setup
CH1 Height
Tail page
CH2 Cross Left
CH3 Cross Right
CH4 Flap Left
AUX3 Right Flap
My RX-Only 7 channel has the following slots:
ESC Motor
Tail page
CH1 Height
CH2 CrossLinks
CH3 Cross Right
AUX1 ???(CH4 Flap Left)
AUX2 ??? (AUX3 Right Flap)
RPM
Who can clarify this?
Regards, Artur
Hallo, wie ordne ich was und wo zu??
Im Menü Modell Setup:
-Ausgabe Setup
CH1 Höhe
Tail Seite
CH2 Quer Links
CH3 Quer Rechts
CH4 Klappe Links
AUX3 Klappe Rechts
An meinem RX-Only 7 Kanal habe ich folgende Steckplätze:
ESC Motor
Tail Seite
CH1 Höhe
CH2 QuerLinks
CH3 Quer Rechts
AUX1 ???(CH4 Klappe Links)
AUX2 ??? (AUX3 Klappe Rechts)
RPM
Wer kann hier Klarheit schaffen.
LG Artur
RV
3 May 2025 23:3603.05.2025 23:36
The RX Only 7Ch is intended for simpler models. High-speed options aren't directly supported. Actually...
But... update your VBC - there was still a bug in the surface mixer to directly access the MCs.
Set the type to Flap/Klapp for both in the surface mixer. The 3-level and Delay MC should then work correctly after reselecting "Type Flap".
Otherwise, you have to manually insert a channel cell into the respective MC for AUX1/2 on the small RX, which simply passes through Ch4/Ch6.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Der RX Only 7Ch ist für einfachere Modelle gedacht. LK sind nicht so direkt vorgesehen dann. Eigentlich ...
Aber ... update mal Deine VBC - da war noch ein Fehler im Flächenmischer um die MC's direkt zu erreichen.
Stelle im Flächenmischer Typ Flap/Klappe für beide ein. Dort sollten dann auch nach erneuter Anwahl "Typ Klappe" die 3-Level und Delay MC passen.
Ansonsten muss man dann noch manuell bei dem kleinen RX in die jeweiligen MC für AUX1/2 eine Kanal Zelle eindrehen welche Ch4/Ch6 einfach durchreicht.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rutra
4 May 2025 08:0004.05.2025 08:00
Hello, could it be that the output slot in the surface mixer is now:
CH4 Master NEO - Wing type flap - Side Left is now right?
AUX3 Master NEO - Surface type flap - Side Right now Left is ?
Regards, Artur (maybe I'm being a bit of a nuisance, but I'd like to fly a flat-screen model with my Touch)
Hallo, kann es sei das nun im Flächenmischer der Ausgang Steckplatz:
CH4 Master NEO - Flächentyp Klappe - Seite Links nun rechts ist ?
AUX3 Master NEO - Flächentyp Klappe - Seite Rechts nun Links ist ?
Gruß Artur (vielleicht nerve ich ein wenig, aber ich möchte ein Flächenmodell mit meiner Touch fliegen)
RV
4 May 2025 08:3704.05.2025 08:37
That doesn't really matter with a landing flap; although I'm a helicopter pilot, I know that both flaps always move in the same direction.
If this is not the case, it is due to the installation position of the servos - and then of course the respective "flap" must be reversed if the "labeling" is to be correct.
The common landing flap itself doesn't care.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Das spielt an sich keine Rolle bei einer Landeklappe, ich bin zwar Heliflieger - weiß aber dass beide Klappen immer gleichsinnig laufen.
Ist dem nicht so liegt es an der Einbaulage der Servos - und dann muss natürlich in der jeweiligen "Klappe" reversiert werden wenn das "Beschriftungsmäßig" stimmen soll.
Der gemeinen Landeklappe an sich ists ja wurscht.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rutra
4 May 2025 10:5204.05.2025 10:52
Yes, if I want to trim the middle, I need to know which flap is on the right or left!
So it should be correctly labelled in the menu view... or you're trimming on the wrong side.
Regards, Artur
Ja wen ich die Mitte trimmen will muss man schon wissen welche Klappe rechts oder links ist!
Also sollte. es in der Menü Ansicht schon richtig gekennzeichnet sein....oder man trimmt auf der falschen Seite.
Gruß Artur
RV
4 May 2025 12:4704.05.2025 12:47
Question:
- How is the CH4 on your Wingmixer labeled (RE or LI)?
- Which of the two connections/MCs (AUX1 or AUX2) does the above signal from CH4 then run to via the channel cell?
- Which servo (right or left steering wheel) is connected there?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Preisfrage:
- wie ist bei Dir im Wingmixer CH4 denn nun (RE oder LI) beschriftet?
- auf welchen Anschluss/MC der beiden (AUX1 oder AUX2) läuft das obige Signal aus CH4 dann via Kanalzelle raus?
- welches Servo (LK re oder LK li) ist da dann angeschlossen?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rutra
4 May 2025 17:2104.05.2025 17:21
Hello,
- CH4 is on the left
- runs on 07/AUX2
- My slots on the RX-Only
ESC Motor
Tail page
CH1 Height
CH2 CrossLinks
CH3 Cross Right
AUX1 Left Flap
AUX2 Right Flap
RPM
I hope I answered everything correctly.
Regards, Artur
Hallo,
- CH4 ist Links
- läuft auf 07/AUX2
- Meine Steckplätze am RX-Only
ESC Motor
Tail Seite
CH1 Höhe
CH2 QuerLinks
CH3 Quer Rechts
AUX1 Klappe Links
AUX2 Klappe Rechts
RPM
hoffe das ich alles richtig beantwortet habe.
Gruß Artur
rutra
4 May 2025 17:5504.05.2025 17:55
Hello, I think I've found the error.
Slots on the RX-Only
06/AUX1 Left Flap...... I have assigned channel 4
07/AUX2 Right Flap... I have assigned it to channel 6.
When I trim in the surface mixer, the right-left assignment is correct!
What does MUX mean???
Sorry, but you first have to get to grips with macrocells.
Greetings Artur and many thanks for your support!!
Edited 3 time(s). Last edit at 05/04/2025 08:28PM by rutra.
Hallo, ich habe vermutlich den Fehler gefunden.
Steckplätze am RX-Only
06/AUX1 Klappe Links...... habe ich Kanal 4 zugeordnet
07/AUX2 Klappe Rechts.....habe ich Kanal 6 zugeordnet
Wenn ich nun im Flächenmischer trimme ist die Zuordnung rechts-links richtig!
Was bedeutet MUX ???
Sorry aber man muss mit den Makrozellen erst mal klar kommen.
Gruß Artur und vielen Dank für die Unterstützung!!
Edited 3 time(s). Last edit at 05/04/2025 08:28PM by rutra.
RV
4 May 2025 21:3204.05.2025 21:32
MUX = Multiplexer - like a railway switch
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
MUX = Multiplexer - wie eine Weiche bei der Bahn
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rutra
6 May 2025 11:4106.05.2025 11:41
Hi, is the model file for a Heron available for download? I tried programming a model based on the videos, but it's not working quite right, or maybe I've missed something.
Regards, Artur
Edited 1 time(s). Last edit at 05/06/2025 11:41AM by rutra.
Hallo, gibt es eigentlich die Modelldatei von einem Heron als Download. Habe mal ein Modell nach den Videos programmiert aber irgendwie funktioniert das nicht so richtig oder ich habe etwas übersehen.
Gruss Artur
Edited 1 time(s). Last edit at 05/06/2025 11:41AM by rutra.
Eddi E. aus G.
6 May 2025 14:0106.05.2025 14:01
Hi,
Do you mean the De Havilland DH.114 Heron 4-engine?
That would be an interesting project :-) but I don't know if there's anything about it yet.
Grüßle
Eddi
Born to fly ...
forced to work.
Hi,
meinst Du die De Havilland DH.114 Heron 4-Mot?
Wäre ein interessantes Projekt :-) wüsste aber nicht, dass es da schon was zu gibt.
Grüßle
Eddi
Born to fly ...
forced to work.
rutra
6 May 2025 17:2606.05.2025 17:26
I mean a model file for a Multiplex Heron!
Regards, Artur
Ich meine eine Modelldatei für einen Multiplex Heron!
Gruss Artur
Eddi E. aus G.
7 May 2025 09:1607.05.2025 09:16
Good morning,
uh :-)
Unless someone reading this has something to add, I don't think so.
I once built such a model myself for testing purposes (a 2m Styrofoam motor glider with four flaps), it was ready in 1-2-3 and flew without problems from the first test throw.
However, it was still with a Silverline with external sensor and satellite, VPlane, Classic.
Unfortunately, I don't have an RX-7 available right now, otherwise I could quickly take a look at where the problem might be with only seven ports.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
ah :-)
außer wenn ein Mitleser hier was hat, denke nicht.
Ich habe selbst mal zu Testzwecken so ein Modell (Styro 2 m Motorsegler mit vier Klappen) aufgesetzt, das war 1-2-3 fertig und flog ab dem ersten Probewurf problemlos.
War allerdings noch mit einer Silverline mit ext. Sensor und Sat, VPlane, Classic.
Hab leider grad keinen RX-7 greifbar, sonst könnte ich grad mal kurz gucken, wo es bei nur sieben Anschlüssen hängen könnte.
Grüßle
Eddi
Born to fly ...
forced to work.
rutra
8 May 2025 11:2008.05.2025 11:20
I simply wanted to compare my file. With the RX Only 7, you have to use a little trickery because the outputs don't match the macro cell menu.
Regards, Artur
Ich wollte meine Datei einfach mal vergleichen. Beim RX Only 7 muss man ein wenig tricksen da die Ausgänge mit dem Makrozellen Menü nicht übereinstimmen.
Gruß Artur