← Setups

Pitch curves translated

Public Talk › Setups · Started by Simon_75 on 1 June 2026 17:5301.06.2026 17:53
Simon_75 1 June 2026 17:5301.06.2026 17:53
Hello

What criteria do you use to adjust the pitch curve?
On the RAW 700 I have a linear curve from -100 to 100, set by the previous owner.
My Goblin 570 has a linear curve from -88 to +88.
I fly 3D, wide-area maneuvers with occasional high-speed bursts. What pitch curve do you use for which flying style?

Best regards, Simon
machine-translated from German · Show original
cc1975 2 June 2026 09:0502.06.2026 09:05
It depends on the pitch angle you're using. I have mine set to +12.5/-12.5 degrees, which translates to +/-90 degrees on the pitch curve of my RS 7 Ultra. It also depends on the resolution, the servo position, the servos used, the linkage geometry, etc.
Regards, Christian
machine-translated from German · Show original
Eddi E. aus G. 2 June 2026 09:5202.06.2026 09:52
Hi Simon,

I fly with a linear setup. The VBar does have a geometry correction for linkages that buckle/unbuckle (switchable for Henseleit/linear servos), which works well with reasonably suitable linkage geometry.

Then it's more a matter of feeling, does it feel somehow strange, non-linear, do you want something softer/with more travel/resolution in the hover pitch range, the blades play a role, or whether you are flying scale and possibly with blades with a lifting profile.

I've gotten into the habit of using the stick :-) but I also see and understand the requirements or desires to adapt something.

It's just a matter of feelings :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Simon_75 2 June 2026 13:0302.06.2026 13:03
Hello and thank you for the detailed answers.

So if I create a new setup with +/- 12 degrees (cyclically 8 degrees), then I adjust the curve for the three banks so that I effectively have the +/- 12 degrees?

So, is it possible that I reach 12 degrees at 88% with the 570, and at 100% with a different mechanism?

I hope I understood it correctly.

Best regards

Simon
machine-translated from German · Show original
Eddi E. aus G. 2 June 2026 13:2802.06.2026 13:28
Hi Simon,

When you create a setup and set the pitch angles there, e.g. +88/–85, these are automatically also the endpoints of the pitch curves.
It makes little sense to have and calculate two values when everything is in one device (it's different with a third-party transmitter, where you also set the maximum angles in VBar, but the transmitter (which VBar knows nothing about except that it's there...) has separate pitch curves that are set to 100/100 by default and thus 'operate' the +88/-85 in the example at full deflection).

The better the lever lengths and rotor head geometry match, the closer you get (in our setup) to 100, which would allow you to utilize the servo travel for which the servo is designed, and not have to electronically limit or increase it.

Pitch curves in VBar Control are now optional, not mandatory.
After the setup, everyone is the same, in this example +88/-85.
This can be changed per bank.
Good to know, because logically, setup comes before flight parameters: if you were to subsequently change the maximum values in the setup, you would also straighten the pitch curves again, namely between the currently valid maximum values...

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Simon_75 2 June 2026 16:0502.06.2026 16:05
Okay, now I understand, thank you for the detailed explanation.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless