← Setups

Trex550/Vstabi/iX14 switching between idle ups translated

Public Talk › Setups · Started by Mvanraak on 21 June 2026 15:5221.06.2026 15:52
Mvanraak 21 June 2026 15:5221.06.2026 15:52
Hi,

I have some questions about my setup;

-Trex 550L dominator
-Hobbywing platinum 100A esc
-Spektrum iX14
-Vbar standard blueline silverline

I have a 3-position switch for idle-up modes; position 1 i have throttle from 0-100,position 2 a straight line 88% (about 2000rpm headspeed) and position 3 a straight line 93% (about 2100rpm headspeed)

The problem is,when i switch between idle-up modes there is no delay so from lower rpm it immediately goes to high rpm and vice versa.

Where can i setup a delay so it goes smooth switching between idle-up modes?

And can i just add expo on the tail in the TX or do i have to do that in the Vbar program on PC?
The same question for adjusting cyclic throw?

Thanks,
Marcel
RV 21 June 2026 16:3221.06.2026 16:32
Quote:I have a 3-position switch for idle-up modes; position 1 i have throttle from 0-100,position 2 a straight line 88% (about 2000rpm headspeed) and position 3 a straight line 93% (about 2100rpm headspeed)

The problem is,when i switch between idle-up modes there is no delay so from lower rpm it immediately goes to high rpm and vice versa.

Very oldscool, manual spoolup - why? Airplane mode? - This ESC handling has been gone since ages ;-)

Please use the ESC governor which has a soft spoolup - or use it with the RPM signal and VBar Governor. If w/o VGov or ESC Gov - as now - ask the radio manual for delays here. in this case we just pass through what comes from it.


Quote:And can i just add expo on the tail in the TX or do i have to do that in the Vbar program on PC?

Select one - eithe Vbar OR radio. Overlapping Expo curves might give some weired behaviour.


Quote:The same question for adjusting cyclic throw?

The throw in flight is only controlled by the FBL determined by the Cyclic Ring setting in dependencie to the collective position (CR is a double-cone-shaped limiter, widest at 0deg collective and narrows to the ends. Set up at hover in setup mode to prevent binding).

If you mean the agitlity which is what you feel - either set in PC soft per Bank or with DR in TX.


We highly recommend using a VBar EVO with a VBar control touch or EVO and the control loop 8.2 for now. A old VBar is out of production since 10 years and also only limited supported.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Mvanraak 22 June 2026 19:3522.06.2026 19:35
I am oldscool haha Ok I guess I can skip the “normal “ idle position from 0-100 and change that setting in my TX (I was a nitro flyer years ago :-)and adjust spoolup time.

But then i still have the problem in the air when I want to switch between low and high rpm/headspeed ?



Edited 2 time(s). Last edit at 06/22/2026 07:37PM by Mvanraak.
RV 22 June 2026 22:0722.06.2026 22:07
Using Vbar Governor - no - if you have set it up according to our manual, we have Delay.
Using ESC external Governor - also not, ESC has delay.

You Spoolup tells me something but NOT one of both above. So - either change or live with that.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless