← Setups

It flies translated

Public Talk › Setups · Started by Master FBL on 27 September 2026 20:3127.09.2026 20:31
Master FBL 27 September 2026 20:3127.09.2026 20:31
Good morning,

Today was Maiden with the tandem mechanism.
For me it was important to see if the modified Goosky RS7s had a modified KEBAB with an O-ring.
They're soft enough for a tandem. I also bought extremely cheap shafts from Dold Mechatronik for 7 euros.
Because I didn't want to drill out the original ones.
What can I say? The helicopter took off visually without any vibrations and hovered along. Fortunately, the extra propulsion system was also designed for other purposes.

I used Jürgen Mahlberg's setup. But it's really unfamiliar to me. Everything is much too soft.
This isn't meant as criticism of Jürgen's setup; I have different heads and reeds, so it can't be compared.
What surprises me most is the tail function. When I make a tail deflection to the right or left, the tail returns to its original position when I release the stick.
I don't know what needs to be changed in the settings.
I think I'll change the unchanged VBar values (original tandem values from the app) for flight mode 3 so I have a comparison.
But I am deeply pleased that the helicopter didn't fall straight from the sky.
machine-translated from German · Show original
JMalberg 28 September 2026 01:0228.09.2026 01:02
Master FBL wrote:
-------------------------------------------------------
What surprises me most is the rear function.
> If I go right or left
> The rear end swings out, causing the rear end to tilt back.
> original position returned when I use the stick
> let go.
I don't know what settings you can change there.
> must.

A lot has changed, especially in the VBAR tandem setup. See there.

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
machine-translated from German · Show original
Master FBL 4 October 2026 18:3704.10.2026 18:37
So.
I went flying again today, and the tail is better with Jürgen's settings; it no longer veers off course. The LiPo batteries have been moved to the rear, and the ESC is now where the LiPos normally sit. I'm only flying the basic mechanics anyway.
But what bothers me most about the tail is that it doesn't respond to the stick input. I've already set the expo to zero.
If I quickly move the stick back to 50%, the rear end moves with a significant delay.
With my 3D machines, it's different; the tail is practically hanging off the stick.
Can't that be changed? I know it's not a 3D helicopter, but following the stick should hopefully be possible?
I don't know if I can simply turn the steering behavior upwards without anything happening.
With the 3D helicopter, I'm at 120, and with the tandem helicopter, at 28.

Or do I need to increase the optimized value from 62?
machine-translated from German · Show original
JMalberg 4 October 2026 23:2304.10.2026 23:23
(Unfortunately, I'm away and don't have access to Chinook)

Hi Janis,

There have been a lot of changes to the settings recently.

Let me guess: The rear end turns like a granny and kind of swings back, but Nick is a roller coaster and almost impossible to keep still?

In my opinion, the reason lies in the very strange sections of the path.
Until now, I thought the hectic nose had to be kept in check by the amount of road traveled, and the tail/yaw likewise. WRONG! Exactly the opposite!
I just discovered that one (or at least I, my tandem) can only get the tandem under control with absurdly varied route proportions.

In the current version of the Tandem app, you can only adjust the path ratios for pitch, nudge, roll, and yaw in the Tandem setup.
I don't remember the old tandem setup. Please upload a screenshot/text copy here, then I can tell you where everything goes.

Adjust the pitch level so that your maximum pitch is 12°.
The nodding component is approximately 80% of the pitch component.
If Pitch is 70, then Nick is 56.

Now calibrate the roll to 8°:
In the standard setup, you can calibrate roll, but do NOT adjust it there; simply leave the value as is. Measure 8° roll there.
In the tandem setup, adjust the roll path ratios until the 8° is exactly right.
It's a constant back and forth, but that's the only way it works.

The rudder/yaw rate is approximately 90% of the roll.

If you now move the sticks for testing in the tandem setup, you will measure absurdly strange pitch values.

My new and flight-based findings show that, unlike what I thought, the path contributions of pitch and yaw/tail must be significantly higher than in the last published setup.

Also tell me the distance between the ball and the rotor shaft center of the linkage from TS to the blade holder and the distance between the ball of the blade holder and the rotor shaft center.
This helps me to estimate where roll and greed need to go.

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )



Edited 1 time(s). Last edit at 10/04/2026 11:31PM by JMalberg.
machine-translated from German · Show original
Master FBL 5 October 2026 06:2005.10.2026 06:20
Hello Jürgen,

Thank you so much for your effort.

Mistake number one is that I set the temperature to 8 degrees in the basic setup menu. I will change that.

I will measure the rest this evening and post it here.

Best regards
machine-translated from German · Show original
Master FBL 5 October 2026 09:4805.10.2026 09:48
One more quick question. You wrote that I shouldn't set the 8 degrees in the basic setup menu.
There's a predefined value of, I think, 75.
Should I just leave it as is, or does it need to be set to 0?

And I have to set the 8 degrees for both the front rotor head and the rear rotor head, right?
machine-translated from German · Show original
JMalberg 5 October 2026 12:3805.10.2026 12:38
Hi Janis,

The 8° calibration isn't a mistake in itself; it simply reflects the need for a clearer and more transparent tandem setup. The same applies to the Max Pitch setting.
The final word has not yet been spoken, and we are still clarifying internally what the exact effects of each method are and which is more understandable.

All FBL systems can only handle one rotor head; none of the FBL systems I know of can independently control two (or even more) rotor heads. The helicopter is supposed to rotate and raise/lower in some way, and the FBL system takes care of implementing these movements as desired.
Everything else is calculated and passed on to the servos, for example by the tandem mixer.
There should therefore be no differences between the rotor heads; they must be mechanically and geometrically identical. I've also noticed that, for some reason, the pitch axis isn't located at the center of gravity. Compensating for this with the pitch travel component for a rotor is confusing, as it results in small additional torque differences that VBAR also has to compensate for. However, if you then notice a significant difference in the rotation axis, it's rather academic :-)
The new tandem app also incorporates adjustments to the pitch and yaw axes relative to the cockpit. However, significant differences in value need to be entered for the adjustments to be noticeable. :-)

For the 8° calibration, leave the value 75 as it is in the basic setting. Do not set it to zero! Otherwise, the roll won't move at all!
For measurement, take the front rotor head and use a second pitch gauge to measure the rear one for comparison only. Both should be almost identical, within 1/10 to 3/10 of a degree.
The same applies in particular to the 0° and Max pitch.
Unfortunately, this is a fiddly and time-consuming process, and it's never exactly the same.

Please remember to send a screenshot of the tandem setup. (With the TS circle thingy at the top.)

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
machine-translated from German · Show original
Master FBL 5 October 2026 19:0905.10.2026 19:09
Hello Jürgen,

First.
Blade holder arm center ball joint center main shaft 29mm
Swashplate ball center main shaft center 17mm

I might need longer ball bolts on the TS.

I've now set it to 8 degrees in the tandem menu; that means pitch is now 80 for 12 degrees positive, roll is 75 (8 degrees), and rudder is 40.

LG Janis



Edited 1 time(s). Last edit at 10/05/2026 07:20PM by Master FBL.
machine-translated from German · Show original
Master FBL 5 October 2026 19:1505.10.2026 19:15
And these are flight parameters that you have adopted.


Flight Parameters Cyclic
Exponential 26 26 26 26
Agility 26 26 26 26
Stick Direct 14 14 14 14
Response 27 27 27 27
Gain 204 204 204 204
Integral 38 38 38 38
Pitch Balance 0 0 0 0
Stop Support 0 0 0 0

Flight Parameters Extended Cyclic
Lightness 0 0 0 0
Integral Discharge 10 10 10 10
Swash Algorithm ----- ----- Version 8.2 ----- -----
Pitch pump 0 0 0 0
Shiver Filter 0 0 0 0
Elev. Precomp. 0 0 0 0

Flight Parameters Tail
Exponential 50 50 50 50
Yaw Rate 24 24 24 24
Response 26 26 26 26
Gain 152 152 152 152
Proportional 97 97 97 97
Integral 47 47 47 47
WAG Suppression 0 0 0 0
Collective precompensation 0 0 0 0
Cyclic Precompensation 0 0 0 0

Flight Parameters Extended Tail
I Limit / Preload 44 44 44 44
I Discharge / Coll. Corr. 0 0 0 0
Differential 0 0 0 0
Stop Gain A 30 30 30 30
Stop Gain B 30 30 30 30
Optimizer A 58 58 58 58
Optimizer B 58 58 58 58
machine-translated from German · Show original
JMalberg 5 October 2026 22:1405.10.2026 22:14
Hi Janis,

The ball spacing of your 2:3 swashplates is almost identical to that of the VARIO Chinook. Not ideal for standard RC helicopters, but probably standard for tandems. Therefore, the control surface deflections should be very similar between a VARIO and yours.

Nick always refers only to "Diff Pitch Nick"; "cyclic Nick" has no meaning whatsoever for roll-controlled tandems.
Pitch 80, then Nick approx. 60
Roll 75, then yaw/stern approximately 55
Nick or yaw can be increased even further, up to pitch or roll.

Until recently, I had the pitch and yaw (and initially also the roll) settings much too low because I foolishly assumed they determined the pitch and yaw rate. However, these rates are primarily determined by the VBAR rate for the nose and tail, which is very low at 20-25 on tandem aircraft.
Try changing Nick down to 25. He should then become sluggish but restless. (Nothing will happen, though; it's all manageable.)
VBAR has too little leeway with Nick=25 and therefore over-/understeers.
A similar thing happens if the tail/yaw rate is too low: the tail noticeably turns to the right when flying backwards, and you have to counter-steer; it doesn't turn at all when flying forwards. If the tail is increased to, for example, 55 degrees or more, the problem disappears.

The VBAR parameters are very similar.
I prefer the Expo setup on the rear with the 26-inch wheel, as the tandem rear end is already a bit sluggish off the mark.
The autotrim needs to be adjusted for roll/aileron, as a tandem with 2 rotors pushes air over the fuselage and therefore rolls away.
Flight Parameters Cyclic Exponential 35 35 35 35 Agility 26 26 26 26 Stick Direct 13 13 13 13 Response 26 26 26 26 Gain 240 240 240 240 Integral 40 40 40 40 Pitch Balance 0 0 0 0 Stop Support 0 0 0 0 Flight Parameters Extended Cyclic Lightness 0 0 0 0 Integral Discharge 6 6 6 6 Swash Algorithm ----- ----- Version 8.2 ----- ----- Pitchpump 0 0 0 0 Shiver Filter 0 0 0 0 Elev. Precomp. 0 0 0 0 Flight Parameters Tail Exponential 26 26 26 26 Yaw Rate 20 20 20 20 Response 32 32 32 32 Gain 162 162 162 162 Proportional 100 100 100 100 Integral 44 44 44 44 Wag Suppression 0 0 0 0 Collective Precompensation 0 0 0 0 Cyclic Precompensation 0 0 0 0 Flight Parameters Extended Tail I Limit / Preload 33 33 33 33 I Discharge / Coll. Corr. 0 0 0 0 Differential 0 0 0 0 Stop Gain A 30 30 30 30 Stop Gain B 30 30 30 30 Optimizer A 60 60 60 60 Optimizer B 60 60 60 60 Flight Parameters Autotrim Trimvalue Aileron ----- ----- 34 ----- ----- Trimvalue Elevator ----- ----- 0 ----- ----- Trimvalue Tail ----- ----- 0 ----- -----
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )



Edited 1 time(s). Last edit at 10/05/2026 10:22PM by JMalberg.
machine-translated from German · Show original
Master FBL 5 October 2026 22:4005.10.2026 22:40
Hi Jürgen, thanks for your help :-)
If you write Diff Nick 60 and heck 55.
I assume this applies to both the front and rear rotors?

It will be tested this week.

Best regards
machine-translated from German · Show original
JMalberg 6 October 2026 16:2506.10.2026 16:25
Hi Janis,

Yes, always adjust both rotors the same.

In your case, it should say:
Pitch/Roll/Tail. 80. 75. 55
Cycle Nick / Diff Pitch Nick. <doesn't matter>. 60

Pitch is fixed by the maximum pitch; here 80 for 12°.
Roll is fixed by 8° calibration; here 75
You can play around with Nick and Heck for a bit longer.
If the pitch or tail is too low, the tandem axle will be unstable on pitch, or the tail will do slow but strange things.
If both are too high, the tandem axle will be unevenly agile or somewhat jerky at the rear.

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
machine-translated from German · Show original
Master FBL 6 October 2026 16:3606.10.2026 16:36
Thanks for your answer.

Best regards
machine-translated from German · Show original
Master FBL 15 October 2026 21:2615.10.2026 21:26
JMalberg Wrote:
-------------------------------------------------------
Hi Janis,
>
> Yes, always adjust both rotors the same.
>
In your case, it should say:
Pitch/Roll/Tail. 80. 75. 55
> Cyclic Nick / Diff Pitch Nick. . 60
>
The pitch is fixed by the maximum pitch; here it's 80.
> for 12°
Roll is fixed by 8° calibration; here 75
> With Nick and Heck you can then do something else
> play.
If the pitch or tail is too low, the tandem axle is on
> Nick is unsettled, or rather, the rear end slows things down,
> but strange things.
If both are too high, the tandem axle will be uneven.
> agile or somewhat hectic on the stern

So,
A big thank you goes to Jürgen

It's almost perfect now with the values entered above.
I set the expo for the rear to 0 so that it better follows my habits.
Increasing the control behavior only introduced instability into the system. So back to 26.
When it stops, it reverses slightly.
I also reduced the Expo for Roll/Captain to 15.
Considering I only have 1330 RPM with the 2-blade head, the plane is already quite agile in pitch. Roll is still a bit lacking. I also increased the pitch by 13 degrees (because it's only a 2-blade plane).
I'm definitely satisfied.
Now comes the finishing touch.



Edited 1 time(s). Last edit at 10/15/2026 09:26PM by Master FBL.
machine-translated from German · Show original
JMalberg 16 October 2026 17:0116.10.2026 17:01
Hi Janis,

:-)

Yes, that also works with my current setup.

The response on the rear speaker is back to 24 and the gain is down to 150, with the proportional gain reduced to 88. Stop gain and optimizer settings are also reduced.

If the rear end spins back, try reducing the response point by point, and also the stop gain.
If he still turns back during backward flight, then increase the integral and decrease the integral limit point by point; but really only by 1-2 points.
Only pay attention to banks 2 & 3.
Flight Parameters Tail Exponential 26 26 26 26 Yaw Rate 20 20 20 20 Response 32 24 24 32 Gain 162 150 150 162 Proportional 100 88 88 100 Integral 44 46 46 44 Flight Parameters Extended Tail I Limit / Preload 33 31 31 33 I Discharge / Coll. Corr. 0 0 0 0 Differential 0 0 0 0 Stop Gain A 31 17 17 31 Stop Gain B 31 17 17 31 Optimizer A 60 50 50 60 Optimizer B 60 50 50 60
Synchronizing the agility of Roll and Nick is really exhausting.
The high proportion of the path length due to roll conflicts with the 8° calibration.
Nick's agility always depends on the amount of distance Nick covers. Too high and the tandem bike somersaults; too low and Nick jumps up and/or reacts strangely. It's a balancing act.
Flight Parameters Cyclic Exponential 35 35 35 35 Agility 26 26 26 26 Stick Direct 13 13 13 13 Response 26 26 26 26 Gain 240 240 240 240 Integral 40 40 40 40 Pitch Balance 0 0 0 0 Stop Support 0 0 0 0 Flight Parameters Extended Cyclic Lightness 0 0 0 0 Integral Discharge 6 6 6 6 Swash Algorithm ----- ----- Version 8.2 ----- ----- Pitchpump 0 0 0 0 Shiver Filter 0 0 0 0 Elev. Precomp. 0 0 0 0
My Chinook is now pretty quiet, but Roll is still noticeably more sluggish than Nick.
It's still a bit too agile for my liking, but now I know how to adjust it.

What are your autotrim values?
But please, whatever you do, don't do a trim flight! That almost went horribly wrong with mine.
Trimming is done easily by hand while hovering in calm conditions.
Flight Parameters Autotrim Trimvalue Aileron ----- ----- 34 ----- ----- Trimvalue Elevator ----- ----- 0 ----- ----- Trimvalue Tail ----- ----- 0 ----- -----
Observe how your tandem bike behaves during pirouettes:
(Prerequisite: Front left-hand rotation)
When yawing to the left, does the pivot point seem to be slightly in front of the center of gravity?
When yawing to the right, the tandem axle pushes to the right and you have to counteract it with left roll? It seems as if the pivot point is almost at the rear rotor?

I'm currently flying around and finding a solution ;-)
Something's sizzling in the kitchen, with a few nice additions. 8-)

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )



Edited 1 time(s). Last edit at 10/16/2026 05:09PM by JMalberg.
machine-translated from German · Show original
Master FBL 16 October 2026 18:1016.10.2026 18:10
Hello Jürgen
I'm currently in Flensburg with friends.
I did a trim flight yesterday.

No problems at all for me. It stood perfectly still.
I don't know what the values are now.
machine-translated from German · Show original
JMalberg 17 October 2026 13:2617.10.2026 13:26
Hi Janis,

Great, my trim flight was... "exciting" :-) :-) ... but VBAR trim flight and I have never been best friends. :-)

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )



Edited 1 time(s). Last edit at 10/17/2026 01:26PM by JMalberg.
machine-translated from German · Show original
Master FBL 19 October 2026 11:5419.10.2026 11:54
[url=http:// https://youtube.com/source/z8bgGheEMQM/shorts?si=zihfU2BkXrR-6iif ]3. Flight Chinook[/url]Moinsen

Here's a short hovering video.


Love, Janis



Edited 1 time(s). Last edit at 10/19/2026 11:57AM by Master FBL.
machine-translated from German · Show original
JMalberg 19 October 2026 14:1219.10.2026 14:12
:-)

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
machine-translated from German · Show original
Master FBL 8 November 2026 18:5508.11.2026 18:55
So, today I flew with 3 LiPo batteries, Expo Roll/Nick is at 10.
I've now set the tail rotation rate to 30 so that the thing can do faster pirouettes.

In this video, starting at 1:50, you can see where I want to go. Mine still has a little way to go before it's that fast.

https://youtu.be/cEJbFi2UPVo?is=xtOvQg8eIPfL5R8K

When he stops, he turns back a little bit.

Roll is still too sluggish for me; I won't dare to fly a roll with it.
It would be nice if it could be implemented at some point to allow separate adjustment of roll and pitch. Pitch maneuverability is very good.

At 1320 RPM, it's really fun to fly around quickly, taking tight turns. The blades rattle very realistically.
How will it sound with 2 pieces of 4 reed heads :-)
The Pyro 800/480 pulls everything through cleanly. I'll have to see if I can get one of my Okon motors rewound so I can do without the first stage, since the straight-cut pinions are a bit noisy. Although it will certainly be much better with a dust cover.



Edited 1 time(s). Last edit at 11/09/2026 04:51AM by Master FBL.
machine-translated from German · Show original
JMalberg 8 November 2026 22:3808.11.2026 22:38
Hi Janis,

super!

Show me your pitch, nimble, roll, yaw rates and the value of the 8° calibration, then I can tell you how to better combine the roll and nimble rotation rates.

If he's still turning back, increase the rearward travel percentage.


Trying to do a roll like a tail rotor helicopter? Don't even think about it! At best, that can only be a barrel roll with a lot of pitch input.
During a roll, you have knife-edge flight and inverted flight.
In knife-edge flight (rotor shafts horizontal), you have no tail control. This means the tandem aircraft must quickly transition through knife-edge flight to use pitch to scoop air downwards again.
Then it's upside down and the tail control system rotates completely in reverse, functioning exactly the opposite way to normal flight. The direction of tail movement is also reversed, but VBAR is unaware of this.
And I've personally experienced what happens to a tail rotor helicopter whose control direction AND FBL effect direction at the tail are reversed: 3 seconds of spinning top.

Therefore, a tandem can never fly a clean vertical turn. It can only be a steep turn with a lot of pressure on pitch and yaw. That was pretty much the first thing Stefan Reusch advised me: Never turn like a tail-rotor helicopter! Never!

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )



Edited 1 time(s). Last edit at 11/08/2026 10:39PM by JMalberg.
machine-translated from German · Show original
Master FBL 9 November 2026 06:0109.11.2026 06:01
Hello Jürgen,

The values are as follows.
Pitch 82
Roll 70
Rear 55
Diff Pitch Nick 60

8 degrees is 75

Stefan Reusch wrote to me that you could already fly fast rolls and loops with a tandem :-)

Best regards, Janis
machine-translated from German · Show original
JMalberg 9 November 2026 11:5309.11.2026 11:53
Hi Janis,

I forgot to mention the min/max pitch and pitch curve :-) But it doesn't make much difference here.
If max-pitch/pitch curve is 100 and path is 82, that results in 100% * 82% = 82%.

The 8° value of 75 and the pitch component of 60 seem about right. That gives 75% * 60% = 45%; on mine, this value is even only 38%. Try testing whether a pitch of 50 makes it feel less agile. Below that, it should start to feel unstable.

An 8° value of 75 and Roll at 70 results in 75% * 70% = 53%; mine is at 60%. Try setting Roll to 80; it should then be more agile in Roll mode.

My theory and practice then say: Nick is controlled by opposing pitch = twice pitch; Roll, however, with two rotors moving in the same direction = once roll.
That means Nick only needs about half the distance as Roll. In your case, it's 45% to 60%. Reducing Nick would then lead to instability. Therefore, I would set Roll at 80.


The tail trim should be set to +/-100 by default on Tandem V1. Combined with a 55% tail control ratio, this also results in a 55% tail balance. You can also try 50% and 60%. At 50%, it should yaw back repeatedly, especially when flying backwards. At 60%, it should hold the tail more firmly and no longer yaw back.

These are my experiences from about 30 flights and a lot of testing and brainpower.


Stefan is right about that! The emphasis is on "FAST". That means with enough pressure on the blades so that the rotor blades are always blowing "downwards" / towards the landing gear.
This can be done with barrel rolls and loops under pressure.

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
machine-translated from German · Show original
Master FBL 9 November 2026 13:0909.11.2026 13:09
Hello Jürgen
Thanks. I'll increase the roll to 80 and see if that improves things.
A tandem glider is definitely easier to fly than I thought. Mine doesn't have that strange pitching motion either.
Yesterday's trim flight went well too. I only used the tail trim, like on my 3D planes.
I always reset the rest to 0.

I forgot to optimize it. I'll test it on Thursday.

Do you perhaps mean the rear path +/- 100 when you say "rear climate"?

Love, Janis



Edited 1 time(s). Last edit at 11/09/2026 01:11PM by Master FBL.
machine-translated from German · Show original
RV 9 November 2026 15:1809.11.2026 15:18
Hi Janis,

If you're interested and would like to follow Jürgen's current development progress, please contact me via email at vstabi (at)mikado-heli.de

The prerequisite would be VBCt/E and VBar EVO.
Currently, the entire thing is only available in German and also for V8 vehicles.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless