After shooting the earlier video here, I still tweaked it a bit. Now it flies quite decently.
(OK let's forget the polite understatement. It's ballistic.)
Note, if you try the setup: You'll need stick input during take-off at least before finishing the trim flight. The problem is, it's very very sensitive, while on the ground. Be gentle on the sticks - the heli starts acting nice only once the skids are off the ground (dial down agility for a start, if needed).
The cyclic gain wasn't calculated but determined iteratively in test flights.
The pictures show the mechanical setup:
Ball links in the blade grips use the outer hole, to reduce pitch range.
The head is mounted as far "up" as it goes. The link lengths are more or less according to the manual. Change the swash-blade links to get zero degrees pitch, when the bell cranks are all centered.
Swash driver spacing (AFAIK not critical).
The lower Jesus bolt goes through the lower hole in the main shaft. As the picture shows, the bottom end of the main shaft is almost flush against the lowest bearing.
Swash servo linkages are parallel. If you can't get them exactly parallel, use slightly shorter arms on the servos.
Geometry correction is on and apparently introduces some asymmetry. Use a 0-x-50-x 93 pitch curve to compensate and get an overall symmetrical pitch range.
Tail servo arm length as shown. The position on the tail boom gives roughly equal travel in both directions. Do not use the full travel range, as this will overload the tail belt. +/- 40 degrees of tail pitch creates a lot of drag. For tail authority, it's pretty useless because of blade stall. Limit pitch to, say, +/- 30 degrees.
I run 95 mm CF tail blades (Mavrikk from fastlad), with light chinese weights on the bolts (an extra nut and a washer).
Finally, the star of the show: mini V-Bar, mounted with connectors heading towards the nose.
Edited 6 time(s). Last edit at 11/21/2009 11:18PM by GravityKills.
Attachments:
open | download - Outrage550.vbr (5.6 KB)
(OK let's forget the polite understatement. It's ballistic.)
Note, if you try the setup: You'll need stick input during take-off at least before finishing the trim flight. The problem is, it's very very sensitive, while on the ground. Be gentle on the sticks - the heli starts acting nice only once the skids are off the ground (dial down agility for a start, if needed).
The cyclic gain wasn't calculated but determined iteratively in test flights.
The pictures show the mechanical setup:
Ball links in the blade grips use the outer hole, to reduce pitch range.
The head is mounted as far "up" as it goes. The link lengths are more or less according to the manual. Change the swash-blade links to get zero degrees pitch, when the bell cranks are all centered.
Swash driver spacing (AFAIK not critical).
The lower Jesus bolt goes through the lower hole in the main shaft. As the picture shows, the bottom end of the main shaft is almost flush against the lowest bearing.
Swash servo linkages are parallel. If you can't get them exactly parallel, use slightly shorter arms on the servos.
Geometry correction is on and apparently introduces some asymmetry. Use a 0-x-50-x 93 pitch curve to compensate and get an overall symmetrical pitch range.
Tail servo arm length as shown. The position on the tail boom gives roughly equal travel in both directions. Do not use the full travel range, as this will overload the tail belt. +/- 40 degrees of tail pitch creates a lot of drag. For tail authority, it's pretty useless because of blade stall. Limit pitch to, say, +/- 30 degrees.
I run 95 mm CF tail blades (Mavrikk from fastlad), with light chinese weights on the bolts (an extra nut and a washer).
Finally, the star of the show: mini V-Bar, mounted with connectors heading towards the nose.
Edited 6 time(s). Last edit at 11/21/2009 11:18PM by GravityKills.
Attachments:
open | download - Outrage550.vbr (5.6 KB)