{"ok":true,"content":"After shooting the earlier video <a href=\"http:\/\/www.youtube.com\/watch?v=9h5nb8mIPSI\" target=\"_blank\" rel=\"noopener noreferrer\">here<\/a>, I still tweaked it a bit. Now it flies quite decently. \r<br>\n(OK let's forget the polite understatement. It's ballistic.) \r<br>\n \r<br>\nNote, if you try the setup: You'll need stick input during take-off at least before finishing the trim flight. The problem is, it's <i>very very<\/i> sensitive, while on the ground. Be gentle on the sticks - the heli starts acting nice only once the skids are off the ground (dial down agility for a start, if needed).\r<br>\n\r<br>\nThe cyclic gain wasn't calculated but determined iteratively in test flights. \r<br>\n\r<br>\nThe pictures show the mechanical setup:\r<br>\n\r<br>\n<hr>\r<br>\n\n\n\n\n\r<br>\nBall links in the blade grips use the outer hole, to reduce pitch range.\r<br>\n<hr>\r<br>\n\n\n\n\n\r<br>\nThe head is mounted as far \"up\" as it goes. The link lengths are more or less according to the manual. Change the swash-blade links to get zero degrees pitch, when the bell cranks are all centered.\r<br>\n<hr>\r<br>\n\n\n\n\n\r<br>\nSwash driver spacing (AFAIK not critical).\r<br>\n<hr>\r<br>\n\n\n\n\n\r<br>\nThe lower Jesus bolt goes through the <i>lower<\/i> hole in the main shaft. As the picture shows, the bottom end of the main shaft  is almost flush against the lowest bearing.\r<br>\n<hr>\r<br>\n\n\n\n\n\r<br>\nSwash servo linkages are parallel. If you can't get them exactly parallel, use slightly shorter arms on the servos.\r<br>\n<hr>\r<br>\nGeometry correction is on and apparently introduces some asymmetry. Use a 0-x-50-x 93 pitch curve to compensate and get an overall symmetrical pitch range.\r<br>\n<hr>\r<br>\n\n\n\n\n\r<br>\nTail servo arm length as shown. The position on the tail boom gives roughly equal travel in both directions. Do <i>not<\/i> use the full travel range, as this will overload the tail belt. +\/- 40 degrees of tail pitch creates a lot of drag. For tail authority, it's pretty useless because of blade stall. Limit pitch to, say, +\/- 30 degrees.\r<br>\n<hr>\r<br>\n\n\n\n\n\r<br>\nI run 95 mm CF tail blades (Mavrikk from fastlad), with light chinese weights on the bolts (an extra nut and a washer).\r<br>\n<hr>\r<br>\n\n\n\n\n\r<br>\nFinally, the star of the show: mini V-Bar, mounted with connectors heading towards the nose.<br>\n<br>\n<br>\n<br>\nEdited 6 time(s). Last edit at 11\/21\/2009 11:18PM by GravityKills.<br><br>\n            \n            \n\n            \n                \n                    Attachments:<br>\n                    \n                        <a href=\"https:\/\/www.vstabi.info\/forum\/file.php?20,file=4558,filename=Outrage550.vbr\" target=\"_blank\" rel=\"noopener noreferrer\">open<\/a> | <a href=\"https:\/\/www.vstabi.info\/forum\/file.php?20,file=4558,filename=Outrage550.vbr,download=1\" target=\"_blank\" rel=\"noopener noreferrer\">download<\/a> -\n                        Outrage550.vbr\n                        (5.6\u00a0KB)<br>\n                    \n                ","note":""}