Bob C
22 December 2023 13:0722.12.2023 13:07
On my Align 700 I have a VBar Control Touch/Evo with vbar Evo rx with pro and rescue added. I also have a 5 blade main head and 6 blade tail rotor. I understand the manual phasing with having a rotor over the tail boom and then rotating the head until it doesn’t move when applying rear elevator and locking it in.
However, when setting up I noted that the swash is set up for H3 120 deg (Norm) because the elevator control is on the front.
The head is setup for 0 deg at centre stick but when I go to check 8 deg I can only get neg 8 deg, is that because the swash is H3 120 deg (Norm) and not hr3 120 deg (Rev)?
Finally, I also see that if I hold down the button on the swash type there is the ability to change the angle, is this an electronic way to phase the head please?
Thanks in anticipation
RV
22 December 2023 17:5322.12.2023 17:53
The 8 deg is independend from the presign - so all okay here.
To get the phasing right - the expert swash is used where you rotate the "servo balls". Each click is 5deg. You can enter the values manually also there. I would adjust this for the standard 90deg. as starting point.
Having a look at the flight parameters for the swashplate and a VBar EVO connected - there is a new phasing control too each bank.
Consider the phasing is in most cases a bit less than 90 deg. and depends on headspeed, blades, dampening etc. - so you can use this value for the fine adjustment each bank at the field.
My BO 105 has 82° at the end. If it is not perfectly matching you may see it in a quickstart from a hover (heli moves a bit sideways first when applying elevator down and collective) or when flying some forward-flight-pirouettes.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 12/22/2023 05:54PM by RV.
Bob C
22 December 2023 19:3922.12.2023 19:39
Thanks Rainer, I found this adjust that did the same. I am taking the 8 deg is only reference for the but plays no part in flying
RV
23 December 2023 10:3623.12.2023 10:36
Quote:I am taking the 8 deg is only reference
Yep. The system needs to know where the 8deg are - this is all.
In flight the real cyclic deflection will be calculated with your given rate by stick (stick deflection and agility set), the direct part (optimizer value) and the control loop part (all gains etc.). It is limited with the cyclic ring to avoid binding then.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 12/26/2023 08:52PM by RV.
Bob C
26 December 2023 16:5426.12.2023 16:54