← Setups

Swash Plate End Point menu adjustment affects mid point translated

Public Talk › Setups · Started by Jerry671 on 18 December 2024 14:5418.12.2024 14:54
Jerry671 18 December 2024 14:5418.12.2024 14:54
In the swash plate End Point menu adjustment, adjusting the Ail Top & Elev Top changes the swash plate being level at mid stick. The Ail Bot & Elev Bot adjustment does not affect the swash plate level at mid stick.

I believe this is a bug in the swash plate end point level menu.

I apologize but I am not near a vbar / Heli as I am still in Thailand and won’t be back to the USA anytime soon, but wanted to see if anyone can shine some light on this issue.


Thanks
RV 19 December 2024 05:5919.12.2024 05:59
This effect is quiet normal as we change the full range - and the center is always recalculated.

To be honest - if you will have a look at the servo horns in center first and align them all the same (90 deg), then work from "bottom to top" on each linkage - i never had the need to use this feature.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Jerry671 23 December 2024 04:3123.12.2024 04:31
Hi Rainer,

I center the servo horns using a 3D printed jig/guide. A long 3D printed arm is screwed on top of the servo arm and a 90 deg ruler along the edge of the servo body. The servo arm is aligned in reference to the 90 deg ruler.

This is a Roban HSM mechanics.

I tried making the servo arm 90 deg to the servo linkage to bell crank. Same issue, swash plate has differential on bottom to Top travel.

In addition, I 3D printed:

1) a bell crank jig so that both bell cranks are 90 degs.

2) a swash leveler / Height jig.

3) a swash lever that mounts to the main shaft an rotated to verify that the swash plate remains level 360 degs at bot, mid & top swash plate travels.

In just about all the Robans HSM mechanics I built, you can see that the swash plate is not level if using a jig to validate the swash plate throughout its travel as compared to the typical method, “close enough for the naked eye” ;-) .

Hence why I like Mikado’s swash plate End point adjustment menu, which you may not see on other FBL software(s).

Although you mention that the software recalculates the swash plate travel as the cause of affecting the mid travel when the top end is adjusted. I strongly think that should not affect the mid range and is a software bug.

My assumption is, if this recalculation is true, then why is the recalculation NOT affected when the bottom end adjustment, if entered a max value adjustment in either directions, the recalculation did not change the swash plate level at mid travel. ONLY the top end adjustment affects the mid travel.

Your thoughts, hope this can be a software future bug fix. Kindly don’t take the word “software bug” as a negative word but just my way to describe the issues ????.

Girard (Jerry)
RV 23 December 2024 08:3623.12.2024 08:36
Hmmm ... i had also a Roban Bell 429 and set up some others too. I have just eyeballed it in center and that was ok, they flew well. So probably - we are trying to fight something here which was implemented for some F3C guys or guys with strange linkages. I'd just set up in center "from bottom to top" as usual and give it a go.

One thing you might run into ... having the newer Roban with the "improved" geometry - IMHO they "improved" too much. So you might run out of throw at some ends too. This happened to me on a clubmates heli and we had to deal with it by adjusting the rods to have enough throw on the positive side.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Jerry671 28 December 2024 01:0028.12.2024 01:00
Hello Rainer,

Per the new bell crank version, I haven encountered any issues with insufficient throws.

Thanks for the response, hopefully my concerns get elevated and addressed. I understand Mikado has a lot going on given the recent surge of other important updates.


Jerry
VStabi VStabi Pioneer of Flybarless