hibor
21 January 2025 18:0621.01.2025 18:06
On my RAW 580 with the VBar Neo running version 6.4, when I perform backward rolls, they are super smooth, and I can chain two rolls without losing speed. However, when performing forward rolls, the helicopter slows down, slightly barrels, and loses a lot of speed. I’ve checked, and 0° pitch is achieved during the rolls in both forward and backward flight.
Could this be due to an incorrect setup in the VBar?
Thanks for your help!
hibor
21 January 2025 18:1121.01.2025 18:11
On my RAW 580 with the VBar Neo running version 6.4, when I perform backward rolls, they are super smooth, and I can chain two rolls without losing speed. However, when performing forward rolls, the helicopter slows down, slightly barrels, and loses a lot of speed. I’ve checked, and 0° pitch is achieved during the rolls in both forward and backward flight.
Could this be due to an incorrect setup in the VBar?
Thanks for your help!
ulrich
21 January 2025 20:4221.01.2025 20:42
The main parameter that influences this symmetry is the CG. If it is dead on, thats a good starting point, but a slight shift forward can help a lot to find a good symmetry.
As second parameter the amount of integral is important. More can help to get the rolls straight in both directions. And finally the amount of gain is relevant. More gain can help getting rid of unwanted effects.
Smaller helis tend to have more difficulties, bigger ones are less critical.
so long ... Uli
http://www.vstabi.de
RV
21 January 2025 22:3921.01.2025 22:39
Could you please check if the COG is spot on?
Another thing could be reasoned in the servo trim values and servo behavior. Please check in setup mode if the servos are forceless when pushing them to their limits1 (Collective and elevator in common). If yes - probably trims are too way off.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Could you please check if the COG is spot on?
Another thing could be reasoned in the servo trim values and servo behaviour. Please check in setup mode if the servos are forceless when pushing them to their limits1 (Collective and elevator in common). If yes - probably trims are too way off.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
hibor
22 January 2025 10:3922.01.2025 10:39
Hey !
Thank you for your anwsers , my Servos are setup up well , I have perhaps no trims on it , and they don't force at the limits.
For my COG , I will check , it 's probably this point , I keep you inform !
Bye
hibor
22 January 2025 11:3222.01.2025 11:32
I check my COG , it's perfectly centered .
On my Vbar setting >> Integral Parameter is set to 60
Full parameter >> Elevator Pre-comp :10
Paddle Sim : 20
Heli Size : 50
Integral : 60
Pitch pump :30
Expo : 10
Collective balance : 35
Lightness : 0
My Main rotor gain : 85 , Raw 580 with 600 mm Blades
Thank you !
Eddi E. aus G.
22 January 2025 11:4722.01.2025 11:47
Hi,
how is it when you do aileron rolls on the spot?
—Eddi
Born to fly ...
forced to work.
hibor
22 January 2025 12:5822.01.2025 12:58
it's pretty balanced. I notice nothing special , the heli roll great.
For information my headspeed , is 1750 Idle 1 and 1900 Idle 2. Same issues with the 2 idles.
Edited 1 time(s). Last edit at 01/22/2025 01:03PM by hibor.
Eddi E. aus G.
22 January 2025 15:2222.01.2025 15:22
I see.
Now please try what Uli suggested: move the battery ever so slightly forward, to shift the CoG a tad, try and compare, work from there if it gets better or worse.
Another thing: when you fly straight FF and input collective up/down, does the model just rise and fall, or does it start to porpoise?
If it does, you could try and adjust elevator pre-comp a bit (try up or down, see if it gets better or worse, iterate).
If it does, this could point to a CoG not being right (dead on is not necessarily perfect), or also to a servo issue, but must not necessarily so.
Kind regards
Eddi
Born to fly ...
forced to work.
hibor
22 January 2025 16:4122.01.2025 16:41
Ok I will try this , when the weather will be more Dry and warm :-)
Thank you !
hibor
3 February 2025 16:2103.02.2025 16:21
I've try today to move the CG Forward , it's really better , my rolls doesn't slow that much.
Thank you
Eddi E. aus G.
4 February 2025 09:2704.02.2025 09:27
Hi,
good!
Another thing I noticed (for me when transitioning from beginner through semi-advanced to idgaf): in some situations (left different than right, backwards different than forwards, rolling circles or eights inwards or outwards) I was (am still ... sigh!) also inputting elevator, inadvertently, also because of the geometry of almost all transmitters (rectangular) where the axis of the hands are rotated inwards, naturally.
Collective timing (and elevator timing in circles, eights) has also a noticeable effect.
It helped, for some time, to tighten the springs in my transmitter a tad more.
So many variables :-)
—Eddi
Born to fly ...
forced to work.
Edited 1 time(s). Last edit at 02/04/2025 09:27AM by Eddi E. aus G..