← Setups

Esc won't spool up motor translated

Public Talk › Setups · Started by Kjell on 16 May 2025 10:3116.05.2025 10:31
Kjell 16 May 2025 10:3116.05.2025 10:31
Hello

I have a Goblin Buddy with a Hobbywing 80 amp V5. VBar Evo and a motor Xnova 3215-930. I don't understand what I have done or not done, but I can't get the esc to spool up the motor.

VBar Control 11004251
VBar EVO. 27004878

Is there a possibility for some help? ????

Regards
Kjell
Eddi E. aus G. 16 May 2025 10:3916.05.2025 10:39
Hi,

checking your logs, I can see that the ESC reports in at power up, the motor switch is actuated, but the ESC does not play ball.

A shot in the dark: is the safety switch programmed/engaged? See Transmitter Settings/Switch Assignments.

Another shot: was the ESC programmed properly in Setup (simply select either VBar Governor or External Governor, or toggle in between to re-load factory settings again), and check/enter motor pole count and gear ratio.

To help seeing what's happening, if the ESC is actually getting a signal, you can temporarily (or parallel, use a y harness) connect a servo to the ESC output on the VBar EVO, so it acts as a pointer, with it's servo arm.

Kind regards

Eddi

Born to fly ...
forced to work.
Kjell 25 May 2025 14:2125.05.2025 14:21
Then I have tried everything you have written, but no difference. Connected a servo, but no reaction from the servo. But one thing I'm wondering about is that when I connect Esc to an LCD program box, it says that Esc is incorrectly connected. But everything is connected correctly. Is there a way to delete everything and start over?

Regards
Kjell
RV 25 May 2025 17:5025.05.2025 17:50
Hello Kjell,

as even a servo does not move - we schould consider the following:

- is there a safety switch assigned and also engaged?
- is the motor switch triggered once to stop before to run?
- does the output work in model setup / esc where you can assign the stick directly to the putput (probably unplug telemetry from HW for acessing this)?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Kjell 25 May 2025 21:4925.05.2025 21:49
Hi, I also thought it was a safety switch that made the motor not start, but I have gone through all the switches and can't see any safe switches. But what do you mean by "is the motor switch triggered once to stop before to run?"
Kjell 25 May 2025 21:5225.05.2025 21:52
I have all the helicopters at the cabin, so I can't check this now. But I'll get back when I've checked what you wrote.
Thanks for the good service. ????
Eddi E. aus G. 26 May 2025 09:5426.05.2025 09:54
Hi,

well, in switch assignments, at the bottom of the list, there's the safety switch.
Make sure it shows 'Open' either permanently, or assign a switch.

Switch to Off or Stop position: this is particularly interesting for Spektrum or Futaba 'switchers', who have the motor switch on one of the spring loaded switches. The motor logic will only arm if/when the motor switch has been to true Off or Stop, for safety reasons.
So you'd want to pull that switch down, it will re-center to Idle, then you can switch to On/Run.

We recommend using a true three-level switch.

Kind regards

Eddi

Born to fly ...
forced to work.
Kjell 26 May 2025 12:3126.05.2025 12:31
Hi

I have switch number 5 for the engine and no other switch for the safe.
Eddi E. aus G. 26 May 2025 13:1726.05.2025 13:17
OK then we can scratch this off the list.

Delete everything, start over: just create a new setup.

To reset the governor only (and related ESC output), toggle between modes (VBar Governor to External, or vice versa, then back).

The servo, does it remain limp, or at a given end position, or at center?

—Eddi

Born to fly ...
forced to work.
Kjell 26 May 2025 14:2826.05.2025 14:28
Hi
No reaction to servo. I think it will be a new setup.
VStabi VStabi Pioneer of Flybarless