Simon_75
1 June 2026 17:5301.06.2026 17:53
Hello
What criteria do you use to adjust the pitch curve?
On the RAW 700 I have a linear curve from -100 to 100, set by the previous owner.
My Goblin 570 has a linear curve from -88 to +88.
I fly 3D, wide-area maneuvers with occasional high-speed bursts. What pitch curve do you use for which flying style?
Best regards, Simon
Hallo
Nach welchen Kriterien stellt ihr die Pitchkurve ein?
Beim RAW 700 habe ich eine lineare Kurve von -100 bis 100, eingestellt vom Vorbesitzer.
Bei meinem Goblin 570 habe ich eine lineare Kurve -88 bis +88.
Ich fliege 3D, Großflächig mit auch mal Einlagen mit viel Speed. Was habt ihr bei welchem Flugstil an Pitchkurve?
LG Simon
cc1975
2 June 2026 09:0502.06.2026 09:05
It depends on the pitch angle you're using. I have mine set to +12.5/-12.5 degrees, which translates to +/-90 degrees on the pitch curve of my RS 7 Ultra. It also depends on the resolution, the servo position, the servos used, the linkage geometry, etc.
Regards, Christian
Kommt ja drauf an mit wieviel Grad Pitch du fliegst. Ich habe z.B. +12,5/-12,5 Grad eingestellt, bei meinem RS 7 Ultra sind das dann +/90 in der Pitchkurve. Kommt ja auch auf die Auflösung drauf an, wo ist die Servokugel, welche Servos werden verwendet, Geometrie der Anlenkung etc.
Gruß Christian
Eddi E. aus G.
2 June 2026 09:5202.06.2026 09:52
Hi Simon,
I fly with a linear setup. The VBar does have a geometry correction for linkages that buckle/unbuckle (switchable for Henseleit/linear servos), which works well with reasonably suitable linkage geometry.
Then it's more a matter of feeling, does it feel somehow strange, non-linear, do you want something softer/with more travel/resolution in the hover pitch range, the blades play a role, or whether you are flying scale and possibly with blades with a lifting profile.
I've gotten into the habit of using the stick :-) but I also see and understand the requirements or desires to adapt something.
It's just a matter of feelings :-)
—Eddi
Born to fly ...
forced to work.
Moin Simon,
ich fliege i. d. R. linear. Eine Geometriekorrektur für ein-/ausknickende Gestänge (abschaltbar für Henseleit/Linearservos) hat die VStabi ja, die bei halbwegs passender Geometrie der Anlenkungen gut passt.
Dann ist's eher eine Gefühlsfrage, fühlt es sich irgendwie irgendwo komisch, unlinear an, will man im Schwebepitch-Bereich was weicher/mit mehr Weg/Auflösung haben, die Blätter spielen eine Rolle, oder ob man Scale und ggfs. mit Blättern mit tragendem Profil fliegt.
Ich hab mir angewöhnt, den Knüppel zu benutzen :-) aber ich sehe und verstehe auch die Anforderungen oder Wünsche, da was anpassen zu wollen.
Gefühlsfrage halt :-)
—Eddi
Born to fly ...
forced to work.
Simon_75
2 June 2026 13:0302.06.2026 13:03
Hello and thank you for the detailed answers.
So if I create a new setup with +/- 12 degrees (cyclically 8 degrees), then I adjust the curve for the three banks so that I effectively have the +/- 12 degrees?
So, is it possible that I reach 12 degrees at 88% with the 570, and at 100% with a different mechanism?
I hope I understood it correctly.
Best regards
Simon
Hallo und danke für die ausführliche Antworten.
Wenn ich also ein neues Setup erstelle, mit +|- 12Grad (zyklisch 8Grad), dann stelle ich die Kurve bei den drei Bänken so ein, dass ich auch die +|- 12 Grad effektiv habe?
Somit kann es sein, dass ich beim 570er die 12Grad bei 88% erreiche und bei einer anderen Mechanik bei 100%?
Ich hoffe ich habe es richtig verstanden.
Liebe Grüsse
Simon
Eddi E. aus G.
2 June 2026 13:2802.06.2026 13:28
Hi Simon,
When you create a setup and set the pitch angles there, e.g. +88/–85, these are automatically also the endpoints of the pitch curves.
It makes little sense to have and calculate two values when everything is in one device (it's different with a third-party transmitter, where you also set the maximum angles in VBar, but the transmitter (which VBar knows nothing about except that it's there...) has separate pitch curves that are set to 100/100 by default and thus 'operate' the +88/-85 in the example at full deflection).
The better the lever lengths and rotor head geometry match, the closer you get (in our setup) to 100, which would allow you to utilize the servo travel for which the servo is designed, and not have to electronically limit or increase it.
Pitch curves in VBar Control are now optional, not mandatory.
After the setup, everyone is the same, in this example +88/-85.
This can be changed per bank.
Good to know, because logically, setup comes before flight parameters: if you were to subsequently change the maximum values in the setup, you would also straighten the pitch curves again, namely between the currently valid maximum values...
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Simon,
wenn man ein Setup erstellt und die Pitchwinkel dort einstellt, bspw. +88/–85, sind das automatisch auch die Endpunkte der Pitchkurven.
Ergibt ja wenig Sinn, wenn alles in einem Gerät ist, zwei Werte vorzuhalten und zu verrechnen (beim Fremdsender anders, da stellt man auch in VStabi die max. Winkel ein, hat aber im Sender (von dem die VStabi nix weiß außer dass er da ist ...) separat Pitchkurven, die standardmäßig eben auf 100/100 stehen und damit die +88/–85 im Beispiel bei Vollausschlag 'bedienen'.
Je besser die Hebellängen und die Rotorkopfgeometrie zusammen passen, desto näher kommt man (bei uns im Setup) an 100, was erlauben würde, den Servoweg auszunutzen, für den das Servo konstruiert ist, und eben nicht elektronisch zu beschneiden oder zu vergrößern.
Pitchkurven in VBar Control sind jetzt ein _kann_, kein _muss_.
Nach dem Setup sind alle gleich, in dem Beispiel eben +88/–85.
Kann man pro Bank ändern.
Gut zu wissen, weil logisch Setup vor Flugparametern kommt: wenn man nun nachträglich im Setup die Maximalwerte ändern würde, würde man auch die Pitchkurven wieder gerade ziehen, nämlich zwischen die jetzt geltenden Maximalwerte ...
Grüßle
Eddi
Born to fly ...
forced to work.
Simon_75
2 June 2026 16:0502.06.2026 16:05
Okay, now I understand, thank you for the detailed explanation.
Ok, jetzt habe ich es verstanden, danke für die ausführliche Erklärung.