← Setups

Rear adjustments EC 135 Vario Turbine translated

Public Talk › Setups · Started by easy on 15 September 2026 21:0915.09.2026 21:09
easy 15 September 2026 21:0915.09.2026 21:09
Good evening, I need some help regarding basic settings for a Vario EC 135 1:6 Turbine PHT3.
Could someone tell me the basic tail rotor settings for the Fenestron? I don't want to crash the helicopter because I entered incorrect values for the maiden flight. Therefore, I would be very grateful if you could tell me some basic values that will at least get the helicopter airborne without it spinning around its own axis.
I have no experience with Fenestron. I have a VBar Neo (not EVO) installed and I'm flying with the VBar Countrol Touch.

I would be very grateful for any tips.

Greetings Andreas



Edited 1 time(s). Last edit at 09/15/2026 09:10PM by easy.
machine-translated from German · Show original
Eddi E. aus G. 16 September 2026 09:1816.09.2026 09:18
Good morning,

Basically, the mechanical components have to be correct first, according to the instructions – of course.

And then I-Limit (limiting the effective range of the heading hold, perhaps starting with 1/3 i.e. 40) and I-Discharge (returning the heading hold 'course pointer' over a certain period of time even without compensation/control input, perhaps starting with 2/3 i.e. 80) will certainly help.

The I-Limit setting is designed to improve the control feel around the center of the flight envelope (less sideslip, cleaner turns) and, secondly, to prevent overloading. For example, in sideways flight, as speed increases, the gyro would control the tail all the way to the stop (because it can...), which could overload the wing. With the I-Limit setting, this effect is limited, and beyond the limit, the model will naturally turn into the wind.

The faster the I-discharge, the more the weathervane effect will favor the circular flight, but there will still be a degree of heading hold, which makes flying and hovering more pleasant overall.

Rotation rate/expo according to personal preference; I wouldn't maximize the sensitivity either; if the tail holds well in scale flight, that's fine.

You won't 'ground' the helicopter right away, just always be attentive, 'feel' the model, hear the model, where the limits are.
It's not a trainer ;-) the rear end doesn't have to crash (otherwise it might only crash once, but really hard...).
Pitch addition/cyclic addition can also be approached more carefully, i.e., push the pitch in in a controlled manner and not – zack –, adjust the pitch addition if necessary, then set the cyclic addition to about 1/3 of the determined value.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
easy 16 September 2026 10:2716.09.2026 10:27
Good morning Eddi,

Thank you so much for your support and quick reply!
I don't want to do anything wrong or risk anything. Here are my rear settings.
Could you please take a quick look and see if this seems plausible to you in connection with the Fenestron?
That would be really great!

Sensitivity 75
Proportional 80
Integral 40
I-Limiter 40
I-discharge 80
Differential 0
Pitch Precomp 28
Cycle. Precomp 8
Stop Gain A and B 0
Optimizers A and B 30
Pendulum suppression 0
Acceleration 35



Edited 1 time(s). Last edit at 09/16/2026 10:28AM by easy.
machine-translated from German · Show original
Eddi E. aus G. 16 September 2026 11:0116.09.2026 11:01
Hi,

Looks OK.

Fens aren't that critical, it's just that people often expect too much (tail performance like with a trainer or like with a normal open tail rotor).
Things become critical when you don't want to believe it and overload the tail, starting with pendulum-like pushing in turns, unexpected turning away (performance limit/wind vane in sideways/backwards flight) and in the worst case ending with mechanical overload.

But the real-life model wouldn't fly sideways or backwards or into a backwards loop at three crazy speeds, the pilot wouldn't fly in a zig-zag-zig elevator motion with the pitch stick, or spin the tail into fast pirouettes and then put both feet on the other pedal and fly back and forth...

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
easy 16 September 2026 11:1516.09.2026 11:15
8-) You're obviously right, but I don't want to do 3D flying with it.
Then I'll attempt the maiden flight with these settings. Thanks again!



Edited 2 time(s). Last edit at 09/16/2026 11:17AM by easy.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless