← Logo 400 ... 690

Logo 550SE resonance noise translated

Mikado Model Helicopters › Logo 400 ... 690 · Started by 590423 on 11 May 2025 17:5511.05.2025 17:55
590423 11 May 2025 17:5511.05.2025 17:55
Hello everyone,
Subject: Logo 550 SE with YGE 95A controller, Savox servos, 1st blades, Vbar Neo, light aerobatics.
During fast forward flight at 1750 rpm, a resonance noise is clearly audible. It doesn't improve even at 1850 rpm.
Furthermore, at low speeds (1500 rpm) a slight torsional oscillation also occurs at the rear.
At a speed of 1750 rpm, the torsional oscillation improves, but it does not disappear.
I tried all possible settings, including different rotor blades, without any change in behavior.
The vibrations are minimal.
The helicopter is otherwise flying normally.
Do you have any idea where the problems might lie?
Thank you in advance for your feedback.
greeting
Philippe
machine-translated from German · Show original
RV 11 May 2025 22:2111.05.2025 22:21
Regarding tail sway:

- Does everything move smoothly?
- Which servo?
- Which stabilization settings?
- Which stabilizer?
- Which software version?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Eddi E. aus G. 12 May 2025 09:0312.05.2025 09:03
Good morning,

A resonance noise indicates that something in the mechanism is vibrating or not running quite smoothly. However, this is normal and not a problem to a certain extent.
When the hood resonates, it becomes audible, like a loudspeaker diaphragm.
One could check if it's seated properly everywhere: the rear hood bolts are usually fine, but if the two halves are touching awkwardly at the back, you might be able to hear it. Or the front spacer bolts – are they actually flush against the hood? Or are they exerting too much pressure? Then, or even in general, the hood might have some play at the front where it's suspended from the skid bracket. Edge protection tape could help here, although you might need to adjust the cutouts slightly, depending on the situation.
You could also glue something (thin) like acoustic/soundproofing foam to the inside of the hood. That's what we did with our BO 105s, which have quite large flat surfaces on the sides. But it's probably not necessary for the LOGO.
For the rear impact, you can use Lego for LOGO (see image gallery here: https://www.vstabi.info/de/node/1971 ).

Rear end, with NEO, just try the pendulum suppression. Turn it up until it's OK.

It could (in combination) really be something at the rear: shaft, hub, blade holder, blades.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
590423 12 May 2025 18:1512.05.2025 18:15
Hello Rainer,

All components move smoothly.
Savox SH1290MG tail servo
Savox SC1257TG rotor head
Neo VBar Pro Rescue
Serial number 0020053101

Tail rotor settings:
Sensitivity 85
Proportional 80
Integral 77
Pitch Precompressor 25
Cyl. Precompress 8
Optimizers A and B 30
Pendulum suppression 12

Rotor head setting:
Maneuverability 80
Sensitivity 95
Integral 60
Pitch Pump 0
Pitch Balance 35
Optimizer values 40
Nick Prekomp 10
Padellsim 10

greeting
Philippe Grenier
machine-translated from German · Show original
590423 12 May 2025 18:2412.05.2025 18:24
Thank you Eddi for your feedback
The hood is firmly in place and, in my opinion, should not vibrate.
I will try increasing the pendulum suppression.
greeting
Philippe Grenier
machine-translated from German · Show original
RV 12 May 2025 18:3912.05.2025 18:39
Hello Phillipe,

Unfortunately, the Savox servos aren't the best choice for the tail. If you continue to have problems there, I would:

- Install a KST or similar tail servo with a short center pulse.
- possibly switch to EVO and set to 1000 Hz

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Eddi E. aus G. 13 May 2025 09:2313.05.2025 09:23
Good morning,

Regarding the feedback, I had a 600 SE many, many years ago.
It had a recurring, rather low-frequency, audible resonance that also changed with the rotational speed.
Then I went to Kyle Dahl's, and his father (his mechanic :-) ) said, "Try replacing the rear belt..." and voilà, everything's fine again.

Perhaps ...

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
590423 26 May 2025 13:0826.05.2025 13:08
Hello everyone,

Here's a short feedback:
I installed the Futaba BLS272SV tail servo from my Logo 700 into my Logo 550 SE.
No resonance noise can be heard, even at full forward speed.
However, the tail remains slightly unstable in hovering flight at 1550 rpm, even with a higher pendulum suppression value.
What can be done?
Thank you in advance for your feedback.
greeting
Philippe
machine-translated from German · Show original
Eddi E. aus G. 26 May 2025 13:1126.05.2025 13:11
Good morning,

Interesting :-)

Quote: Philippe
with higher pendulum suppression value

How high?

But the tail is only 100% still when the helicopter is switched off and sitting on the table ^^

Which governor is YGE running? If in doubt, please simply switch between them, VBar to YGE or vice versa, and compare.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless