← Logo 400 ... 690

Logo Trainer Acc translated

Mikado Model Helicopters › Logo 400 ... 690 · Started by MaxtNix on 28 June 2025 05:5528.06.2025 05:55
MaxtNix 28 June 2025 05:5528.06.2025 05:55
Hello,
Just a question about the coach.
Yesterday I wanted to do a training session again and, for my birthday, I simply allowed myself the time to finally do it again.
So I packed everything up, and because I'm still not entirely sure about my Touch Control, which I was able to port to the trainer thanks to your help, I used the original controls. The wind was reported as 3.5 m/s, but it was also gusty, probably twice that.
Because of other flight operations, the helicopter was set to 4x8m, so I was practicing at about 5-6m height and suddenly the helicopter took off.
I lost control of it, my model airplane buddies weren't quick enough to get there, and the helicopter crashed somewhere in a rye field. I couldn't find it yesterday; after three-quarters of an hour, six of us called off the search for the time being.
Today I'm buying a used camera drone and we won't give up the search.
Is it possible that a strong gust of wind pushed the small helicopter out of the ultrasonic cone, making it uncontrollable? I think I also loaded the rescue function for stabilization onto the receiver when transferring the settings to the larger controller. I'm not entirely sure, but it didn't work. I've had lessons at a flight school and I can usually hover and recover the helicopter to a certain extent. But nothing worked. I also thought that maybe I could make a noise with the tail rotor running to make it easier to locate. That didn't work. Nevertheless, the battery voltage was showing as dropping relatively quickly, as if there was a load on it. It's all a bit puzzling to me. But perhaps someone here knows what I should pay attention to when I get it back. Alternatively, I bought an OMP2 before the trainer. Is there a way to buy a retrofit kit to convert it to a trainer?
I'm curious if you can broaden my understanding of this disaster and financial bankruptcy.
machine-translated from German · Show original
Wingtip 28 June 2025 20:5028.06.2025 20:50
Hi,
Sounds to me like the trainer function has been deactivated.
Was the landing platform also loaded?

Normally, the logo doesn't move out of the area when everything is active.
What mode were you using?

An M2 from OMP is similar in style, but it cannot be upgraded to the Mikado Trainer.
machine-translated from German · Show original
MaxtNix 29 June 2025 09:4329.06.2025 09:43
Hello,
So, the switch on the right was set to Trainer mode; I never fly it any other way at our airfield, or anywhere else for that matter. Also, everything is always fully charged before I go to the airfield, even with my fixed-wing aircraft. I've had my share of experience with the OMP, and that's precisely why I invested in the trainer. I was assigned a small corner where I wouldn't disturb normal flight operations, and after I demonstrated and explained it, I was allowed to fly there. Someone always keeps an eye on things there, and if I can't even get the hang of the OMP, I'm certainly not going to switch off the trainer. Another thing I noticed was that the tail rotor wasn't responding to normal control. If I turned the helicopter slightly, it would always return to its neutral position after releasing the control stick. But before I could properly understand and process that, and before I should have actually landed it, it was already gone.
Well, so far the search has been unsuccessful; nothing has been found with the camera drone. I've since been told that if I had flown with the touch controls, I would have had a chance to find the trainer via the signal strength indicator. It's especially annoying since I had the controls with me, but it's not that easy to understand them and be sure of using them.
Well, we'll see. I can't afford a new trainer on my meager pension; if all else fails, I'll have to write it off and bury the helicopter flight....



Edited once. Last edited on 29.06.2025 at 09:47 by MaxtNix.
machine-translated from German · Show original
Eddi E. aus G. 30 June 2025 09:2230.06.2025 09:22
Good morning,

We are sorry to hear that.

I'll try to pick out and answer a few questions:

Wind – in my opinion, it's not a problem. At Global 3D, we had a flying area for demonstrations, testing, and public flying. That day, the wind was around 30 km/h with significantly stronger gusts, so 8-12 m/s (at times even more, I think). This didn't faze the instructor once throughout the day, even when children were flying, simply putting the sticks down and watching the helicopter dance. They were flying battery after battery after battery; at times, we even had two helicopters ready to go for the sake of continuous power (heat) and for faster rotation.
There was a real commotion there, by the way, with competition flights (you know how loud those can be), the noise system was loud with commentary and music and so on, so that you had to speak very loudly to be able to have a conversation at all.

Flying away – how exactly does that work? Because normally, in trainer mode, the helicopter would sacrifice itself (shut down, crash to the ground) if it left the flight zone. And especially when flying in a small airspace, you have even less chance of going out of bounds, since the cone size or the transmission power/volume isn't adjusted; instead, an invisible boundary is simply drawn tighter within the space. Even at maximum extent, you have a safety margin; it would be quite negligent to risk it.
This means (in my head) that if I have a 4x8 m area and some space around it as recommended, the helicopter will at worst fall off the edge without power, not flying over/into a field... except in a storm ^^

Heli/yaw axis, after release to starting position? That actually means that it works (tail rotor power, attitude and direction are detected and controlled), but it may not have been taken over yet (pitch back/forward), i.e. still under close control of the system.

I would also guess it's the trainer switch. Which, by the way, would be the beginner/floating mode in normal operation with or without the platform, in the rescue function that's on the trainer.
I'm not sure what would happen if you fiddled with the rescue settings on a 'large' VBar Control (...), since you said rescue didn't work with it. Perhaps you did manage to change something in such a way that it no longer worked with the trainer.
However, this would need to be checked/tested with the model; until then, it remains only a vague assumption.
Nevertheless, this is yet another reason for us to advise against using it, or to only do so at our own risk, creating further uncertainty.

If everything were (back) working, fingers crossed!!, I would check the microphone levels, battery voltages, and the LOGO antenna status with VBar Control Touch to see if anything is visible.

If all else fails, we can also talk about a new LOGO 200 trainer for the existing platform and transmitter, but it cannot be ported to another helicopter, the tuning is very specific – which is why you should never change settings in trainer bank 1 with a 'large' VBar Control, and only fly in bank 1 (with Basic always bank 1 anyway, automatically).

We recently had a customer here with a LOGO 200 (without a trainer) where two out of three (apparently quite new) battery packs were faulty. He only discovered this using the current-voltage sensor and a 'large' VBar Control. Fully charged, everything seemed fine, but after a short time, the controller was at full throttle, and the RPM still dropped because the battery voltage was falling incredibly fast.
So there could always be one more reason than you currently have in mind :-/

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
MaxtNix 30 June 2025 11:0930.06.2025 11:09
Hello, thank you for the detailed questions and information.
So, first of all, I actually bought the VBar Touch for my Goblin 770, which I use for my flying lessons. I've been flying with Jeti for a very long time. When I read here in the forum that it was possible to use the trainer with it, I asked about it, was given the go-ahead, and was allowed to do it. However, I'm still having some problems with the Touch. There are things I don't understand because, on the one hand, they're only accessible on the controller itself, but not on the websites here where the information and apps are located, and on the other hand, because you can't work with it offline like you can with Jeti. My flight instructor was the only one who configured the settings for the Goblin. Of course, nothing was touched on the logo; that was a prerequisite for being allowed to do it. But I also couldn't find the settings on the Touch that specifically concern the cone, and I haven't been able to check with my flight instructor (MfKC Switzerland) yet, so I've been flying with the original controller.
Yes, I have to honestly say I was perplexed. I've done a lot of training flights with the Logo, and there's never been even a hint of any problem. In fact, the helicopter simply flew out of the cone, and by the time I realized what had happened, and in a more or less panicked state trying to get it under control as best I could, I ended up just crashing it. As for the rescue function, I don't even really know if I activated it. I was too panicked, and I haven't had a chance to practice it with the original controls yet. It's pointless in trainer mode too. And with the larger model, I'm still practicing hovering, and I've never needed or practiced using the rescue switch there either.
I've now spent over 20 minutes searching with three drone flights, most recently using a spotter app on my tablet. No luck. My clubmates are coming this evening; the farmer has been notified, and we'll search the field again with several drones and, as a last resort, in person. Hope springs eternal.
machine-translated from German · Show original
Eddi E. aus G. 30 June 2025 12:1830.06.2025 12:18
Hi,

I understand. I think so :-) Such a long text with almost no paragraphs is sometimes difficult to read and mentally structure ;-)

Touch, flight space: simply flip the trainer switch.
Just like with the Basic version.
Then the display switches to the trainer menu, and you can, in color, ...
It would be illogical to change the logic.

If you were able to control the helicopter (possibly not bring it under control, but control it, even crash it), you were no longer in trainer mode.
This is something you can easily replicate (ideally with an experienced pilot). Start in the trainer, fly around, switch out, fly a few circuits freely, climb high, fly far, perform aerobatics, fly back into the cone, switch the trainer back on, it takes over again, and lands automatically.

Conversely, it becomes more difficult or dangerous because the trainer only gets sharp and takes off and flies when everything works.
Otherwise, one could simply carry the running model away from the platform to see that it shuts down when it leaves its habitat.
The helicopter, however, resists being moved away with everything it has while in flight.
The more daring might be tempted to try hovering it above the platform and pushing it away from there by the skid or the tail boom. Just a little bit.
Don't do this at home , but it's practically impossible anyway; even a 200 is a force of nature.
Anyone tempted to simply carry the platform away now... that won't work either, the helicopter will follow.

Regarding the touchscreen and settings: if you're used to complicated things, it can get quite complicated...
But if you engage with it, what do I want, create a new setup, what is offered to me, I choose the most obvious one, what does the transmitter want from me, I scroll down and answer the questions, oh, already done, pre-flight check, test run, go flying... then I don't have to deal with it offline, at best I just tap (?) if I have a (?) question.

If I want to read a good book, it's not a manual.

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless