HelipilotMike
7 June 2026 19:3607.06.2026 19:36
Hello,
I need a new swashplate for my Logo 10! Are replacements still available? Or what would be an alternative? The black plastic ring on my swashplate has come loose. I noticed it when I was looking at it. Lucky me. I've been flying it since 2007. I'm grateful for any advice.
Greetings Mike
Hallo,
Ich brauche für meinen Logo10 eine neue Taumelscheibe!. Gibt es noch Ersatz?. Oder was währe eine Alternative. Bei meiner Taumelscheibe hat sich der schwarze Kunsstoffring gelöst. Habe ich beim drüberschauen bemerkt. Glück gehabt. Fliege den auch schon seit 2007. Ich bin für jeden Tipp dankbar.
Grüße Mike
Christoph68
7 June 2026 22:5307.06.2026 22:53
Hi Mike,
I think the original throttle stem for the L10/L400 is already sold out, but maybe Mikado still has one. Or you could find one at an online retailer. Alternatively, the throttle stem from the larger Logo models should also fit (L550/600/690, which also have a 10 mm rear axle). It's a bit more robust and has a slightly different geometry, so you might have to adjust the throttle stem setup a bit. Or you could glue the inner ring into the metal part of the throttle stem. That happened with my L400SE years ago. It's held ever since I glued it in place. The newer throttle stems had a crimped edge, so this problem didn't occur with those.
Warm regards
Christoph
Hallo Mike,
ich meine, die Original-TS für den L10/L400 ist bereits abverkauft worden, aber vielleicht hat Mikado ja noch eine. Oder Du findest noch eine bei einem Händler im Netz. Alternativ müsste auch die TS aus den größeren Logos passen (L550/600/690, die haben ja auch eine 10 mm HRW). Ist halt etwas massiver und hat auch eine leicht andere Geometrie, so dass Du ggfs. das TS-Setup etwas anpassen musst. Oder Du klebst den Innenring in den Metallteil der TS ein. Ist bei meinem L400SE vor Jahren auch passiert. Nach dem Einkleben hält sie seitdem. Die neueren TS hatten später eine Bördelung, da ist das dann nicht mehr aufgetreten.
Herzliche Grüße
Christoph
Eddi E. aus G.
8 June 2026 08:5608.06.2026 08:56
Good morning,
Uh... the world has turned twice as fast since then :-) from plastic to the 'small' aluminum swashplate to the current one.
'In principle' – correct – with small adjustments (checking paddle deflections, 8° and min./max. pitch with VBar, linkage lengths and free path on the shaft) any swashplate for 10 mm shafts will work, in this case
this one .
But cleaning, roughening up a bit, and carefully gluing the joint in place with epoxy (making sure not to get the ball or bearings dirty ^^), as Christoph correctly writes, will probably last forever.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
uh ... die Welt hat sich inzwischen zweimal weiter gedreht :-) von Kunststoff zur 'kleinen' Alu-Taumelscheibe zur aktuellen.
'Im Prinzip' – richtig – geht mit kleinen Anpassungen (Ausschläge mit Paddeln, 8° und min./max. Pitch mit VStabi, Gestängelängen und freien Weg auf der Welle prüfen) jede Taumelscheibe für 10 mm Wellen, in dem Fall
diese.
Aber reinigen, etwas aufrauen, bspw. mit Epoxy vorsichtig das Gelenk einkleben (dabei nicht die Kugel oder die Lager einsauen ^^), das hält wie Christoph richtig schreibt vermutlich für die Ewigkeit.
Grüßle
Eddi
Born to fly ...
forced to work.
HelipilotMike
8 June 2026 15:4808.06.2026 15:48
HelipilotMike
8 June 2026 15:4908.06.2026 15:49
Okay, I'll give it a try. Thanks to both of you!
Ok Probiere Ich mal aus Danke euch beiden
HelipilotMike
13 June 2026 13:3813.06.2026 13:38
So my logo is flying again! I glued the inner ring in with epoxy.
Greetings Mike
So mein Logo fliegt wieder!. Hab den Innenring eingeklebt mit Epoxy.
Grüße Mike
Eddi E. aus G.
15 June 2026 08:5215.06.2026 08:52
:-)
Born to fly ...
forced to work.
:-)
Born to fly ...
forced to work.