← Logo 200

Logo 200 (old) - Evo conversion - rear failure translated

Mikado Model Helicopters › Logo 200 · Started by thomas1130 on 14 November 2025 17:4014.11.2025 17:40
thomas1130 14 November 2025 17:4014.11.2025 17:40
Hi everyone,

I had a Logo 200 here (ancient) - still with large servo connectors - and an "old" Evo - still with hot glue fix...

I thought to myself - why not "marry" both - if you use the Evo without the cover - even the hood fits...

The conversion was easy - the preset for Logo 200 was already there on the V8 - only the rear was switched to 500Hz/1520ms - and the trim of the TS was adapted.

It flew great too - tail super stable - but only for a minute - then out of nowhere, tail failure in mid-air - helicopter spins out - engine cuts out - crash...

Not much happened - rebuilt - exactly the same thing again :-/ :-)

40 seconds of great flying - tail completely gone - crash :-)

Does anyone have any idea where the problem might lie?
The helicopter flew perfectly with the Neo mini - and with the Evo too - although only for 40 seconds at a time.

Everything works again afterwards on the workbench.

Somehow the old "tail control" seems overloaded to me? - could that be?

I have no idea where to begin...

Best regards,
Thomas

machine-translated from German · Show original
RV 14 November 2025 20:1514.11.2025 20:15
Was the regulator perhaps very hot?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
thomas1130 14 November 2025 21:1714.11.2025 21:17
Unfortunately, I haven't tested that :-)

Between the two crashes, I had a relaxed flight with only figure eights – that went smoothly...

On the other two flights, I went in harder - and after about 40-60 seconds the tail simply "shut down" - the helicopter was of course completely uncontrollable.

It worked every time afterwards on the workbench.

I'm guessing it's "overload" - or a loose connection - both are hard to find.

Next time I'll feel the controller to see if it gets warm - it doesn't have much cooling surface - chassis on the bottom, Evo glued on top...

However, this worked for years with the Neo mini - is the load really that much higher at the rear due to the Evo V8?

Thanks & best regards,
Thomas



Edited 3 times. Last edited on 14/11/2025 at 21:21 by thomas1130.
machine-translated from German · Show original
Jurrien Saelens 15 November 2025 17:2915.11.2025 17:29
Hopefully my ESC will continue to hold up well. I did five flights again today without any problems. I fly three minutes of relatively hard 3D, but not extreme, in Bank 3 and then land in Bank 2. My settings are in the other post.
machine-translated from German · Show original
Simon630 9 February 2026 21:0009.02.2026 21:00
Hello Thomas,

Have you found a solution for that?
I occasionally experience the same rear-end failure.

Regards, Simon
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless