← Logo 200

Logo 200 rear motor/controller defective? translated

Mikado Model Helicopters › Logo 200 · Started by Jan790 on 16 August 2025 00:3416.08.2025 00:34
Jan790 16 August 2025 00:3416.08.2025 00:34
Good day,

I have a small, but big problem with my Logo 200. On Monday, the tail failed during flight; I had almost no control over it and landed the little plane in, thankfully, tall grass. Shortly before, I heard an unusual humming noise from (presumably) the tail motor, but I wasn't able to get down quickly enough, and while attempting to turn for landing, the tail failed.

No major damage to the helicopter; the tail boom is straight, as is the main rotor shaft; nothing is visible on the head. The tail fin is cracked, the metal bracket for the tail motor is slightly bent, one main rotor blade is slightly bent, and one skid is slightly cracked.

I replaced all the damaged parts (thanks again for the super fast shipping).

I ran the helicopter on the bench without the blades. I double-checked that the main rotor shaft was perfectly straight. Everything seems fine here; no vibrations. The unusual humming from the tail motor was also gone.

The problems arose during the test flight. During spool-up, the message "Extreme Vibration Level" appeared intermittently. Everything seemed normal in hover, but during quick stops from a turn, the tail swung excessively, especially to the left. To the right, it seemed to turn very slowly, as if the motor wasn't reaching sufficient RPM. This oscillation occurred on all banks (at standard RPMs). Additionally, the message "High Vibration Level" appeared, which I had never seen before. The highest vibration level was 2600.

The last flight before the crash was about 30 minutes prior, and everything was fine then. I don't fly 3D; I just fly my usual relaxed to sporty circuits.

I found older posts about a burnt-out rear engine, but it doesn't smell burnt, there's nothing to see visually, and it never got stuck anywhere.

I would still suspect the motor and the vibrations caused by the strong oscillations. Could it be something with the speed controller after all?

I bought the good one in September 2023.

Best regards,

Jan
machine-translated from German · Show original
Eddi E. aus G. 18 August 2025 08:5618.08.2025 08:56
Good morning,

Regarding the vibration level, I would simply run the helicopter very carefully in my hand, keeping all rotating parts away from me, and look at the vibration analysis (graphic) to see where it is coming from.

In my opinion, the after-oscillation does not generate any vibrations, since there is practically nothing mechanical there except for two electric motors with propellers.

There was a strange case where a 200-series behaved 'oddly', and it was somehow due to the current sensor.
If one is installed, unplug it from the VBar and plug the battery directly into the controller, then try it.

If you can't clearly identify it, the only solution is to swap parts: first the rear motor and possibly also the propeller if it doesn't look fresh anymore.

If that doesn't help, try the regulator too.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Jan790 18 August 2025 16:3718.08.2025 16:37
Hi Eddi,

There is no current sensor installed.

I had already replaced the tail propeller and main rotor blades. There's nothing visibly wrong with the propeller, but I have some more and will replace it again.

To see the graphs, do I need the Pro version? It's not included with the 200, and the button is grayed out. I haven't needed the Pro version yet for my small helicopter, which I only fly occasionally in the garden or on the lawn.

I still tried running it in my hand, no vibration notification, but it did when it was on the floor.

I guess I'll start by replacing the rear motor.

Best regards,

Jan
machine-translated from German · Show original
Maik1702 18 August 2025 19:1218.08.2025 19:12
Hi Jan,
I once mounted the rear spoiler backwards, which resulted in a swaying rear end.
Is yours mounted the right way round?

Regards, Maik
machine-translated from German · Show original
Jan790 18 August 2025 23:0718.08.2025 23:07
Hi Maik,

That was one of the first things I checked, because I had the same thought. But it's on the right way round.
And in the crash, he already lacked control over the rear, and he was either facing the wrong way or he had maintained very good performance for a long time facing the wrong way :-)

Best regards,

Jan
machine-translated from German · Show original
Eddi E. aus G. 19 August 2025 09:0319.08.2025 09:03
Good morning,

For normal vibration analysis, you don't need a pro, and you can see the vibration levels live when it's running.
The 200 series usually has none at all...

But if the rear motor and propeller have already been replaced, the next suspects would be the main rotor shaft and the blade bearing shaft, and generally overtightened main rotor blades (just so that they 'hang' loosely when the model is held in knife-edge flight).

If the controller, for example, 'plays along' in your hand, i.e., if you let it spin up, then carefully turn it around the vertical axis, and it generates thrust at the rear (the little thing has quite a bit of power!), and doesn't stutter, build up and release power unevenly, or make any strange noises, then everything _should_ be OK.

If vibrations/shaking are visible on the ground (hard surface) and also in the live vibration analysis display, but not in flight, then perhaps (only?) the skid brackets or mounts are bent. Both skids must lie flat when the aircraft is stationary. This can easily be adjusted with pliers; as long as the aluminum parts aren't cracked or badly bent, nothing will break. I then grip the most suitable angled piece near the screw with the pliers, bend it with (minimal) force, set it back down, check, and adjust until it's straight again.

Greetings

Eddie

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
ikarus991 19 August 2025 10:3819.08.2025 10:38
In my case, it was once a defect in the rear motor,...
If it keeps getting stuck in the grass during takeoff/landing...
You could see that something was getting thicker under the heat shrink tubing right next to the motor...
I replaced the entire rear end, then it was quiet.....

wolfgang
machine-translated from German · Show original
Jan790 19 August 2025 12:4619.08.2025 12:46
Hey,

The new rear motor is on its way. I'll report back after installation and testing.

When I rotated it around its vertical axis in my hand, it moved upwards without feeling jerky. I can confirm the bit about the power :-)

There were vibrations during flight, but the tip about the skids is still good; they weren't making 100% contact. I'll readjust them later and check the graphs again while the new motor is on its way.

Thank you and best regards,

Jan
machine-translated from German · Show original
Jan790 20 August 2025 22:5220.08.2025 22:52
Hello,

I did some more testing with and without the main rotor blades and tail prop.

The main rotor blades were tightened so much that they would fall downwards in knife-edge flight with a very slight "jerk"; that's how I had them before.

First of all, I can't display the graphs for vibration analysis. The Vbar help menu also says Pro is required, see screenshot. I can also confirm that I can see the graphs on Vbars that have Pro installed and have already used them.

I tested it on a smooth surface (laminate), all settings in bank 1, 3800 RPM (factory setting). When running with the rotor blades in place, the vibration level reached a whopping 3000... and the tail was unstable on the ground, meaning it wobbled back and forth. This probably isn't as noticeable on grass because the helicopter can't move around as easily. When running with only the tail prop and without the tail prop, the vibration levels were 274 and 251 respectively, without any tail wobble. However, I couldn't detect any rough or uneven running of the main rotor shaft, and the blade grips appear to be aligned, which should indicate a straight blade shaft.

The new rear motor should arrive tomorrow, then I'll tinker with it and test it over the weekend.

Best regards,

Jan

machine-translated from German · Show original
Jan790 7 September 2025 23:2807.09.2025 23:28
Hello,

I've finally gotten around to working on the logo again, so here's a quick update:
The tail motor and boom (which was very slightly bent) were replaced. During the replacement, it was discovered that one of the rods to the tumbler was also slightly cracked, so that was replaced as well. Vibrations are somewhat better, but still "high vibration level" on the ground and when handheld.

One more question: I've noticed that the rotor blades aren't at the same height when folded to the side in the trim setting, but outside of the setup, they are at the same height when the stick is centered. Shouldn't they be the same in the trim setting within the setup?

Otherwise, the next assumption would be that a bearing of the main rotor shaft has been damaged and that is where the vibrations are coming from.

Best regards,

Jan
machine-translated from German · Show original
RV 8 September 2025 06:2408.09.2025 06:24
They should actually be set up like this. It's impossible to evaluate this outside of the setup because the control loops are already active.

So - in the setup, adjust something using the pitch trim.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
ikarus991 8 September 2025 14:5708.09.2025 14:57
So if a control rod to the swashplate had a crack, then the helicopter crashed.
I've grounded mine countless times! Then I always dip all the shafts and bearings to save myself unnecessary troubleshooting; the parts really don't cost much, and I want to fly, not troubleshoot...

wolfgang
machine-translated from German · Show original
Jan790 8 September 2025 15:1608.09.2025 15:16
Hey Wolfgang,

Yes, as I wrote in the first post, I crashed because the rear end stopped responding. It will probably come down to replacing bearings, etc. Of course, I'd like to know what was wrong with the rear end so I don't crash again right away. But I also think the vibrations are a result of the crash.

You have other helicopters to fly while you repair the broken ones.

Best regards,

Jan
machine-translated from German · Show original
Jan790 28 September 2025 20:3828.09.2025 20:38
Good morning,

Another update on my Logo. I finally got around to replacing the main rotor shaft and bearings, and went flying today. I also replaced the bearings on the blade grips and the damper. The vibrations are gone, so something was definitely damaged in the crash.

The tail still isn't cooperating properly. Hovering works, but turning is extremely sluggish. During a full pirouette, the helicopter starts to wobble a bit at the end. It seems like the tail motor can't keep up or it's lacking power. So the cause of the crash hasn't been fixed. When running it by hand and gently turning it, it does seem like the motor has enough power, but of course, I have no comparison to the expected performance, and it's sufficient for hovering.

Since the motor was already new, the only thing left is the controller, or could it also be something related to the Vbar? Nothing was changed in the settings, though.

Best regards,

Jan
machine-translated from German · Show original
Eddi E. aus G. 29 September 2025 08:5529.09.2025 08:55
Good morning,

Let's talk about the settings :-)

What are the ones for the rear?

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Jan790 29 September 2025 20:3629.09.2025 20:36
Hi Eddi,

I've attached screenshots of all the settings. I haven't changed anything except the expo; it's all factory default. After replacing the main rotor shaft, bearings, and linkage, I also adjusted the main rotor trim slightly.

Under Autotrim, I noticed the -120 setting for the rear, which seems very extreme. Autotrim was never enabled on my car. To be honest, I never looked at the menu before (it came pre-trimmed and worked fine :-)), but I imagine the value wasn't always like that, or perhaps wasn't intended to be.

Thank you and best regards,

Jan

machine-translated from German · Show original
Eddi E. aus G. 30 September 2025 08:5530.09.2025 08:55
Good morning,

It looks normal.

The Autotrim -120 is also OK, this is due to the fact that the tail rotor only delivers thrust in one direction.
If you were to set that to 0, the rear end would feel very strange.

Sluggish means the tail reacts with a delay, or the rotation rate is low even at full deflection, or...?
Both directions?
All the benches?

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Jan790 30 September 2025 18:3430.09.2025 18:34
Good morning,

By "sluggish" I meant the rotation rate is low even at full deflection, and it takes a while for the helicopter to get going, so everything is somewhat delayed. This is the case in both directions, and slightly worse clockwise, which makes sense since the motor has to work harder then. When coming out of a counter-clockwise rotation, you can actually see the motor slowly ramping up again, and it takes a moment before you're back in a comfortable hover. I'd never noticed this before. The problem is present on all banks.

I can see if I can get it on video during the next flight, if it's possible to upload them here, but I can't say when that will be yet.

Best regards,

Jan
machine-translated from German · Show original
Eddi E. aus G. 1 October 2025 09:0701.10.2025 09:07
Good morning,

OK. Video, sure, then please upload it somewhere where videos belong and have enough space, and then link it here.

What parameters are set for the tail servo? With the standard setup as I just loaded it, the limits would be set accordingly and the control frequency would be 500 Hz/1,520 µs.

Normally, the rear end is aggressive enough for pretty much anything you throw at it.
I have no idea what could have happened to the controller that would cause it to seem to start turning with a delay, or why the VBar should be delayed with those parameters.

And the only things that could slip would be the bell housing or the shaft on the motor, but that was new.

That really only leaves – correct – the controller or the stabilizer, and since I'm not practically familiar with this after just a few days of experience with VBar, I would most likely guess the controller.

*There's nothing that doesn't exist: there have been isolated cases where 'somehow' practically no proportional but I was set, then it can feel like this.
Essentially, only one part of the control loop (the integrator) is given a change in the rotation rate, and it then accelerates relatively slowly.
The part that goes directly from the control stick to the rear is missing.
It's like giving an autopilot a course correction, which it then carries out in a passenger-friendly manner, instead of putting the control stick in the corner.
This is easily fixed, or rather, if you load a new setup, everything will be back to normal.

One more test would be: connect a tail servo to the VBar for testing purposes (note: wide pulse and 500 Hz are set, please check/adjust beforehand, then switch back).

If it can be controlled normally, or if it reacts normally and directly to movement of the VBar, as one is used to with a 'normal' helicopter, then it is most likely not the VBar.
You can also try reducing the P-value to 20 (minimum), and you will see that the tail servo takes its time when steering.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Jan790 1 October 2025 19:2301.10.2025 19:23
Hi Eddi,

In my setup, I don't see the tail servo parameters at all. I only have the one side from the screenshot in my second-to-last post in the model setup. Normally, I can adjust everything here in the setup. I also don't see the tail servo's proportional gain; I only have Expo, Yaw Rate, and Gain.

Firmware is VBar Logo 200 Express, version 6.4.31 VBar Neo Mini

I can't find any newer updates via the Control either. To register in the App Store, I'd need to connect the Vbar to the PC via USB. Is there a special cable that connects to the pins on the Mini? I couldn't find anything in the shop.

I still have a tail servo lying around here to connect, but of course not without first getting to the settings.

I can create a completely new setup in the next few days; perhaps I'll then have more options, at least I can choose helicopters other than a Logo 200.

Best regards,

Jan
machine-translated from German · Show original
Eddi E. aus G. 2 October 2025 09:0402.10.2025 09:04
Good morning,

Well, the Express works as we have parameterized it; if nothing can be configured, then nothing can be changed (or have been changed).

The VBar can be conveniently registered or updated via the transmitter using WLAN: Transmitter settings, VBar NEO/EVO Updater, Check, QR code, ... or simply updated if there is something new.

If you have a standard digital servo lying around (wide pulse), I think you can just plug it in.
I have a Savox connected here, which according to the spec doesn't support 500 Hz, only 333 Hz, but that works.
But you can always adjust things like frequency and output pulse in the setup.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Jan790 11 October 2025 13:2211.10.2025 13:22
Good morning,

I always managed to overlook the QR code registration and registered my Vbars once via USB and the manager... that's so much more convenient :-)

There are no newer updates, so everything is fine.

When the weather cooperates again, I will film the flight, then redo the entire setup and connect a servo.

Best regards,

Jan
machine-translated from German · Show original
Jan790 5 November 2025 00:3405.11.2025 00:34
Good day,

I finally got around to flying the helicopter twice and filming it myself/having it filmed. The tail felt better now/no longer sluggish, and even after rewatching the videos, the rotation rates during the pirouettes in the banks don't look too bad at all. I almost never fly bank 1, and that might be why it felt sluggish.

All rotations were performed with the stick at full deflection. I think you can clearly see that the helicopter tilts to one side during the pirouettes (sometimes I then reflexively pull it straight up), no cyclic pitch input.

I now think the vague feeling and the tendency to tip over when turning are coming from the main rotor. Overall, it takes significantly more effort to keep it in place than before. When I get around to it, I'll redo the entire setup and test it again (the weather and my busy schedule aren't cooperating at the moment). Otherwise, could a servo have been damaged in the crash? I couldn't see anything wrong with it on the test bench.

Videos (just ignore the unnecessary chatter in the first one :-) ):

https://www.youtube.com/watch?v=Id8ZKKSGYJw

https://www.youtube.com/watch?v=T_y0ExatLLU

Best regards,

Jan



Edited twice. Last edited on 05/11/2025 at 00:37 by Jan790.
machine-translated from German · Show original
Eddi E. aus G. 5 November 2025 10:0105.11.2025 10:01
Good morning,

To me, it looks as if the helicopter is (still) massively (?) mistrimmed.

. remove all trims (Setup, and Trim Flight Menu Roll and Pitch, tail remains at -120)
Adjust the swashplate mechanically at stick center positions (Trim menu) as horizontally as possible, and if necessary (fiddly...) move the servo arms on the output shafts one notch further to get closer to horizontal – be careful with the screws, it has happened that someone has sheared off the screw heads ;-)
. Level the TS completely via the trim menu
If necessary, adjust the linkage lengths (all three or all two the same length) so that the swashplate is then at approximately 0° pitch (fold in the blades); minor deviations can also be easily adjusted via the trim menu.
. Trim flight in little/no wind outside, or if there is enough space, inside – leave the auto-trim window open, keep an eye on it: when the values no longer change or start to move slightly back and forth by one value, it's done.

Normally, it is sufficient to trim electronically, first using the trim menu (horizontal by eye, 0° pitch by folding), then performing the trim flight.
Better (but more time-consuming) is to rework it mechanically if necessary.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Jan790 10 November 2025 22:0210.11.2025 22:02
Hi Eddi,

Yes, the settings are still from before the crash; I only adjusted the control rods and folded the blades to 0°. The swashplate looked pretty level. But I'll reset everything from scratch, including a trim flight, as you suggested.

You also think the yaw rate from the tail looks okay? That should be independent of the poorly trimmed model, right? Then it seems it was only the motor.

Best regards,

Jan
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless