← Cafe

Heli veers left during takeoff translated

Public Talk › Cafe · Started by berggimpel on 31 August 2026 17:4731.08.2026 17:47
berggimpel 31 August 2026 17:4731.08.2026 17:47
Hello fellow helicopter pilots,
I own a large Lama with a three-leaf head and four servus for the swashplate.
The swashplate rotation is perfectly adjusted and the helicopter flies very well in itself, however, the problem at takeoff is that the Lama immediately wants to veer to the left.

I've read something about phasing, but I can't make sense of it and I don't know which direction to set the swashplate rotation in.

This is a right-handed glider with a flying weight of 22 kg.

I hope you can help me with this.
machine-translated from German · Show original
RV 31 August 2026 21:3431.08.2026 21:34
Hello Hubert,

Please check if the beginner mode (rescue app) is active.

In principle, right-handed motors always have a side thrust to the left, but this is usually quickly corrected. Do you perhaps have the I discharge for cyclic operation enabled in the "starter bank"?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Eddi E. aus G. 1 September 2026 08:5301.09.2026 08:53
Good morning,

Please also describe what the helicopter is doing: is it pushing to the left, or is it rolling to the left?

Does the swashplate perhaps move unintentionally as soon as the drive starts?

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
berggimpel 2 September 2026 10:4502.09.2026 10:45
Hi Rainer, hi Eddi,

Thank you for your quick response.

Rainer, please explain to me what you mean by "starting bank, cyclical".

Eddi, the swashplate is perfectly straight when switched on and the Lama rolls to the right.

Regards, Hubert
machine-translated from German · Show original
Eddi E. aus G. 2 September 2026 11:2702.09.2026 11:27
Hi,

Ah, now on the right :-) (First post, left...).

Starting bank, the bank you selected when you started the helicopter and it took off.

I-discharge is a tail parameter that reduces the heading hold to zero over a certain period of time (discharges the preload). This can help to return the tail rotor to the center if the helicopter has been rotated while being carried out and the tail is not centered again using the stick.

In flight, it acts like a soft heading hold, i.e., a weathervane effect occurs because the heading hold (I-component, integrator) does not rigidly adhere to the direction or to small control inputs.

But that has nothing to do with Roll.

Now in more detail:
The motor starts up, pitch 0°
You're placing the model lightly on the skids, applying pitch, and probably not (yet) using cyclical control.
The model takes off.

-> When exactly does what happen?
Once the model is hovering freely, the effect disappears, right? ("The helicopter flies very well in and of itself" ;-)

The trim may not be correct (a swashplate that is exactly horizontal is too neutral, or may pull slightly to the right), and only once the model can move freely can the VBar intervene to counteract the skew.

Such an effect could also occur if the center of gravity were significantly off.

Try this: deliberately trim the swashplate one or a few clicks to the left; does anything change?
Or maybe do a trim flight and see what kind of values are generated.

Beginner mode would also be a topic, and it would not be good, for example, to perform the trim flight in beginner mode!

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
berggimpel 2 September 2026 17:3902.09.2026 17:39
Hi Eddi,
Let me explain this briefly,
The helicopter starts at zero pitch and immediately drifts away upon takeoff. I've now trimmed it again and it's significantly better, but I'm not entirely sure why, as I've already done two or three trim flights and everything was fine then.

The I-component at the rear is deactivated.

Well, that's fine now, I just thought it might have something to do with phasing.

Regards, Hubert
machine-translated from German · Show original
RV 2 September 2026 19:3902.09.2026 19:39
Ask:

Is there a log of this in the cloud?
Which serial numbers (VBC and Stabilizer) are in the game?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Eddi E. aus G. 3 September 2026 09:0503.09.2026 09:05
Good morning,

No, phasing only takes effect with noticeable control inputs, and then dynamically, the more, the more, or when the airflow between the advancing and retreating blades becomes increasingly different with speed.

During takeoff or hovering, this would mean that the stabilization system wants to pull forward or backward (e.g., against the center of gravity), but due to a twisted control signal, this results in a roll impulse.
The deviation would have to be quite significant (+/- 20° is practically imperceptible while floating).

A deviation from the geometric 90° is actually normal, because the geometrically 90° leading (or trailing...) linkage and also the exactly horizontal swashplate rarely (never...) correspond exactly to the neutral position (force balance without control or stabilization input) due to the head, blades, tail rotor side thrust, etc.

Here's another thought experiment (or rather, a real-life scenario): if you hover the helicopter without any significant external influences, on which side does the skid 'hang'?

It is actually normal that you have to make slight corrections when taking off (on a level surface) so that the helicopter doesn't start to drift sideways (not: to roll continuously around the longitudinal axis!).

In beginner mode, however, this can (briefly) happen when the stabilization pulls the helicopter onto the artificial horizon.
Once the effect is achieved, the hovering position (tilt) can be set so that the artificial horizon is essentially leveled on it.

But help Rainer out, I'm curious where he wants to go :-)

Grüßle

Eddi

Born to fly ...
forced to work.



Edited 1 time(s). Last edit at 09/03/2026 09:06AM by Eddi E. aus G..
machine-translated from German · Show original
berggimpel 4 September 2026 11:2104.09.2026 11:21
Hi Eddi,

I think I've finally got it working; I just trimmed it some more and now it goes almost vertically upwards on takeoff.
In flight, the helicopter leans slightly to the right, but I think that's normal for a right-handed helicopter.

Thanks for your help. Regards, Hubert
machine-translated from German · Show original
berggimpel 4 September 2026 11:3104.09.2026 11:31
Hi Rainer,

The VBar neo has the serial number 2002 8702

The new transmitter has the serial number 11007810

Regards, Hubert
machine-translated from German · Show original
RV 4 September 2026 19:5304.09.2026 19:53
Hello everyone,

The log looks good. But what I'd like to know is – when you look in the stick calibration menu – what are the resting positions?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
berggimpel 5 September 2026 10:5105.09.2026 10:51
Hi Rainer,
The stick position is exactly in the middle, but what I don't understand is that the neck sensor stick status has various settings ranging from crazy to classic. What does this mean?

Regards, Hubert
machine-translated from German · Show original
Fingolf 5 September 2026 11:0705.09.2026 11:07
Read the help text about it.

Stephan
machine-translated from German · Show original
berggimpel 5 September 2026 20:3905.09.2026 20:39
Hi Stephan,

Which help text are you referring to? I can't find any.
Regards, Hubert
machine-translated from German · Show original
RV 5 September 2026 23:0805.09.2026 23:08
I wasn't referring to the Hall sensor settings, but rather the stick calibration itself. Is it always 0% in the center position?

Help => click on the question mark there ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
berggimpel 6 September 2026 18:3906.09.2026 18:39
Hi Rainer,

The joysticks are all positioned exactly in the middle and are displayed as such by the Hall sensors.

But I'd also like to know what the button on the Hall sensors means: normal or crazy? There's no question mark or help text.
machine-translated from German · Show original
RV 6 September 2026 23:5306.09.2026 23:53
Quote: I was n't referring to the Hall sensor settings , but rather the stick calibration itself . Is it always 0% in the center position?

You're right about the clubs, I just saw them.

The classic approach is roughly what we've had so far regarding the processing of the stick inputs (retroactive filtering / proactive prediction). The higher the value, the more aggressive/faster the processing becomes, and the lower the value, the more subdued it is.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




Edited 2 time(s). Last edit at 09/06/2026 11:54PM by RV.
machine-translated from German · Show original
Eddi E. aus G. 7 September 2026 09:1007.09.2026 09:10
Hi Stephan,

Unfortunately, he's right, there isn't one.
That wouldn't be bad though :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Fingolf 7 September 2026 10:5707.09.2026 10:57
Let me see, I think we did that too.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless