← VPlane / VBasic VLink

The elevators do not move in parallel. translated

VBar › VPlane / VBasic VLink · Started by heliechris on 10 February 2025 16:0310.02.2025 16:03
heliechris 10 February 2025 16:0310.02.2025 16:03
Hello,
I have a problem and I just can't get any further.
I have an Extra 330 with one elevator servo on each side. When I'm in the setup menu and adjust everything to "Servo Center, Endpoints" and check it with a digital scale, I get the same upward and downward deflection on both sides.
If I exit the setup and set the maneuverability for bank one to, for example, 30, then I have different values on both sides. For example, CH1 shows 12 degrees at the top and 13 degrees at the bottom, while on the other side it's almost the opposite. If I set the maneuverability to, for example, 50, it gets even worse. Only in the setup menu is everything the same.
I've attached the setup file.

Thanks and regards
Chris's file attachments:
Open | Download - 11005444_vplane_EXTREM_330.zip (566 bytes)
Open | Download - 11005444_macro_EXTREM_330.zip (244 bytes)
machine-translated from German · Show original
RV 10 February 2025 17:2910.02.2025 17:29
Everything is working as it should for me. I just tested it on the workbench with your setup.

Different angles top/bottom could, however, result from the different paths.

Try this:

- Set the surface mixer CH1 to -100/0/100 (paths and center)
- In the MC, go to CH1 and set a "channel" cell with input MC01/CH1 (essentially the output of the surface mixer)
- the same applies to the MC at CH4 - input MCV01/CH1

Now, configure the directions, centers, and travel for the connected servo on both microcontrollers. This ensures that both receive the same stabilization signal.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
heliechris 10 February 2025 18:2410.02.2025 18:24
Thank you very much for the quick reply.

I did it as you said, but unfortunately nothing happened on the elevator when I moved the pitch control. Then I went...
I'd like to use FCNick as the input signal in MC/CH1 and CH4 as you described. Can I do it that way?

In any case, it seems to work even with bank switching.

greeting
Chris
machine-translated from German · Show original
RV 10 February 2025 18:3110.02.2025 18:31
Then please both FC Nick - go.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless