Volker Wahlen
25 March 2025 12:0625.03.2025 12:06
I have a question.
If I use the macro function "Curve", will the mixers no longer work, e.g., aileron/rudder?
Does the sensitivity for attitude stability only work for the ailerons but not for the elevator and rudder?
Are the original Expo values also switched off then?
Bank switching is also obsolete.
Greetings from sunny Thailand
Volker
Edited once. Last edited on March 25, 2025 at 12:07 PM by Volker Wahlen. File attachments:
Open |
Download - 11006398_vplane_Adiction_Neu.zip (618 bytes)
Open |
Download - 11006398_macro_Adiction_Neum.zip (305 bytes)
Ich habe da mal eine Frage.
Wenn ich die Makro Funktion Kurve benutze, funktionieren dann die Mischer nicht mehr, z.B. Quer aus Seitenruder?
Auf funktioniert die Empfindlichkeit Lagestabilitaet nur noch auf die Querruder aber nicht mehr Höhen und Seitenruder?
Die Originalen Expowerte sind dann auch weg geschaltet?
Bankumschaltung ist auch obsolet
Gruesse aus dem sonnigem Thailand
Volker
1 mal bearbeitet. Zuletzt am 25.03.2025 12:07 von Volker Wahlen.
Dateianhänge:
öffnen |
Download -
11006398_vplane_Adiction_Neu.zip
(618 bytes)
öffnen |
Download -
11006398_macro_Adiction_Neum.zip
(305 bytes)
Eddi E. aus G.
25 March 2025 13:1625.03.2025 13:16
Good morning,
If the _input_ is the original output on the connection, then yes. For example, servo on CH2 <- curve <- input CH2.
The problem is (there's always something...) if I flatten the curve very much, _all_ outputs are reduced there, including stabilization, including mixing, proportionally as if the smaller spike would occur.
Is the thing normally unflyable with maximum expo, or are you just doing that to please the Futaba fans? :-) ;-)
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
wenn der _Eingang_ die ursprüngliche Ausgabe auf dem Anschluss ist, schon. Bspw. Servo an CH2 <- Kurve <- Eingang CH2.
Das Problem ist nur (irgendwas ist immer ...) wenn ich die Kurve sehr flach stelle, sind _alle_ Ausgaben dort reduziert, auch Stabilisierung, auch die Mischung, halt anteilig so wie der kleinere Ausschlag zustande käme.
Ist das Ding denn mit max. Expo normal unfliegbar, oder machst Du das nur, um den Futaba-Jüngern zu gefallen :-) ;-)
Grüßle
Eddi
Born to fly ...
forced to work.
Volker Wahlen
26 March 2025 03:3426.03.2025 03:34
The plane has "huge" control surfaces and is very light.
This makes it very sensitive, especially during landing.
It's some kind of aerobatic thing.
So they set full paths, but made them more sensitive by using much more exposure.
Here with Vbar, even at 100 Expo, the dimming isn't as drastic as with Futaba. You know the curves, right?
I am also a Futaba disciple, but I want to get to know and understand your system much better and show them that it is possible.
I had hoped and thought that these macros would only affect the sticks, the selected input signal, and not the sum output.
It seems to be different when rolling; it's still okay then.
As the "commissioning manager," I would have had my programmers do it that way.
Otherwise I would have selected other inputs, but there aren't any that would need to be addressed.
Greetings from sunny Thailand
Volker
Der Flieger hat "riesige" Steuerflächen und ist sehr leicht.
Dadurch sehr empfindlich vor allem bei der Landung.
Es ist so ein Kunstflug Ding.
So haben sie volle Wege eingestellt, aber um Null, durch viel Expo feinfühliger..
Hier mit Vbar ist selbst bei 100 Expo nicht so brutal dimmbar wie Futaba. Ihr kennt ja auch die Kurven.
Ich bin ja auch ein Futaba Jünger, will erstmal euer System viel besser kennen lernen und verstehen und denen zeigen das es doch geht.
Ich hatte die Hoffnung und den Gedanken, das diese Makros nur die Sticks, ausgewähltes Eingangssignal und nicht den Summenausgang, beeinflussen.
Scheint beim Rollen anders zu sein, da geht es noch.
Als "Inbetriebnahmeleiter" hätte ich es von meinen Programmierer so machen lassen.
Ansonsten hätte ich andere Eingänge auswählt, gibt es nicht, die dann zu behandeln wären.
Gruesse aus dem sonnigem Thailand
Volker
Eddi E. aus G.
26 March 2025 09:0426.03.2025 09:04
Hi Volker,
Well, one could also mix stick and stabilization (FC) together, then curve them, or curve them individually before mixing, then output them and see if you get the desired result.
But when it comes to sensitivity/twitchiness, especially in slow flight and during landing, I would try it without macro cells and with one bank dedicated to that, turning down agility (flattening the entire turn, like dual rate), and possibly also increasing stabilization (sensitivity). Set the second bank to medium, and the third bank to extreme.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Volker,
naja, man könnte auch Stick und Stabilisierung (FC) miteinander mischen, dann bekurven, oder vor dem Mischen einzeln bekurven, dann ausgeben, schauen, ob man zum entsprechenden Ergebnis kommt.
Aber wenn es um Empfindlichkeit/Fickrigkeit insbesondere im Langsamflug und bei der Landung geht, würde ich es ohne Makrozellen und mit einer Bank dafür probieren, Wendigkeit runter (flacht die ganze Kurve ab, wie Dual Rate), Stabilisierung (Empfindlichkeit) ggfs. zusätzlich hoch. 2. Bank mittel, 3. Bank brutal.
Grüßle
Eddi
Born to fly ...
forced to work.
Dirtygeri
26 March 2025 09:2326.03.2025 09:23
Hi Volker!
Eddi beat me to it... I fly several "3D monsters" (elevator with 50 to 70 degrees of deflection) without any problems using my Vbar Control, exactly as Eddi described... Bank 3 with agility of 100 (torques, flat spins, etc.), Bank 2 with agility (depending on the model - it's individual) of 40 to 70 for "nice" flying, and Bank 1 (instructor/student, possibly landing) with agility between 30 and 50...
Works perfectly! Give it a try...
Best regards, Geri
Hi Volker!
Eddi ist mir zuvor gekommen ... ich fliege problemlos einige "3D-Monster" (Höhenruder mit 50 bis 70 Grad Ausschlag) mit meiner Vbar Control und zwar genau so, wie Eddi es beschrieben hat ... Bank 3 mit Wendigkeit 100 (Tourquen, Flachtrudeln, usw.), Bank 2 mit Wendigkeit (je nach Modell - ist individuell) 40 bis 70 für "schönes" Fliegen und Bank 1 (Lehrer / Schüler, ev. Landung) mit Wendigkeit zw. 30 bis 50 ...
Funktioniert problemlos! Probiere das mal aus ...
LG Geri
Volker Wahlen
27 March 2025 02:5227.03.2025 02:52
Sounds good. I had 30, 50, 70 maneuverability yesterday and 100 expo.
Our retired Dreamliner was happy with it yesterday, even in strong crosswinds.
The plane remained perfectly still with stabilization support and flew super straight even inverted.
He didn't notice anything.
I hadn't enabled macros, so it worked after all :-)
Thank you so much for your help.
Greetings from sunny Thailand
Volker
Klingt gut. Hatte 30, 50, 70 Wendigkeit gestern und 100 Expo.
Unser Dreamliner Rentner war damit gestern zufrieden und das bei starkem Seitenwind.
Der Flieger stand mit Stabi unterstützung ganz ruhig und flog super geradeaus auch bei invers.
Er hat nichts davon gemerkt.
Hatte die Makros nicht zugeschaltet, ging also doch :-)
Vielen Dank für die gute Hilfe.
Gruesse aus dem sonnigem Thailand
Volker
Eddi E. aus G.
27 March 2025 09:1327.03.2025 09:13
:-)
...following the motto, "can't be done" doesn't exist; either it's more difficult, or (in this case) done differently :-)
The beauty of our stabilization is that you don't feel like you have to work against it, but can always freely control the model.
Otherwise, torn figures, causing a flow separation in figures or 3D would hardly be possible.
—Eddi
Born to fly ...
forced to work.
:-)
... frei nach dem Motto, geht nicht, gibt's nicht, entweder geht es schwerer, oder (in dem Fall) anders :-)
Das schöne an unserer Stabilisierung ist ja, dass man eben nicht das Gefühl hat, dagegen arbeiten zu müssen, sondern das Modell stets frei steuern kann.
Sonst wären gerissene Figuren, herbeiführen eines Strömungsabrisses in Figuren oder 3D auch kaum möglich.
—Eddi
Born to fly ...
forced to work.