← VPlane / VBasic VLink

Setting up VBASIC without a gyro as a pure RX translated

VBar › VPlane / VBasic VLink · Started by JMalberg on 15 March 2025 17:1515.03.2025 17:15
JMalberg 15 March 2025 17:1515.03.2025 17:15
Hey everyone,

I'm completely stuck and can't find it in either the forum or the instructions:

I would like to temporarily use my VBAR EVO as a pure RX without a gyro to control another FBL.

The VBC EVO is loaded
- VBAR Evo Basic Setup
- VBAR Evo Pro additional setup (cannot be deactivated)
- VBASIC (RX without receiver)

Pro Rescue is loaded in the VBAR EVO

When creating a new model, only helicopters are suggested to me, and the gyros are always active.
Even when I load VBAR Plane, I can only create new models of helicopters with gyroscopic capabilities.

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )



Edited once. Last edited on 15.03.2025 at 17:16 by JMalberg.
machine-translated from German · Show original
RV 15 March 2025 18:1115.03.2025 18:11
I can unlock VBasic for you - however, I hope you have fun without helicopter-specific features like pitch curves and flight phases...

Maybe start with the M2 setup and see if you can get it to work or bend it.

Since no serial number is given... we'll just go around again... JÜÜÜÜRGGEEEN

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 15.03.2025 18:11 von RV.
machine-translated from German · Show original
JMalberg 20 March 2025 10:0820.03.2025 10:08
Hi Rainer,

I don't need anything specific to helicopters, as far as I know, since it should only be used for controlling a third-party FBL (Bavarian Demon) via SUMD:
Only one fixed flight phase
Pitch - Direct
Roll - Direct
Nick - Direct
Rear - Direct
Constant speed
Gyro - Constant

That should also work with VBAR Express/Pro by "switching off" all gyros.

I'll take a look and report back.

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
machine-translated from German · Show original
ulrich 20 March 2025 10:5820.03.2025 10:58
SUMD outputs via the macrocells (starting at cell 11; E1Ch1), and there's the option to use the direct channels as input for the macrocells, i.e., "Roll," "Pitch," or "Tail." These are the transmitter signals directly and without stabilization. What the algorithm does next is then completely irrelevant. The switches can also be routed to any channel in this way.

So long... Uli
http://www.vstabi.de
machine-translated from German · Show original
Eddi E. aus G. 20 March 2025 11:0220.03.2025 11:02
Hi,

This always works if you build the macrocells E1 ff. directly with the sensor as input and as channel.
Direct (stick) control also means that maneuverability, expo, for example, no longer have any effect.

Or curve cells instead of channel cells, or something in between (a fail-safe position can be stored in channel cells).
Or H1 swashplate without sensitivity (0), then you practically have discrete channels, but with the normal adjustment options.

For speed, it's best to use FC ESC as the input (motor logic with fail-safe), external governor, percentage value (constant).

Discover the possibilities :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
RV 20 March 2025 15:3820.03.2025 15:38
That's exactly what the M2 does... it provides the 3 control functions, pitch curves and RPM settings plus an additional function as S.Bus on AUX1.

Therefore => load M2, test, if necessary switch to CH MC Rev if direction is wrong.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 20.03.2025 15:39 von RV.
machine-translated from German · Show original
JMalberg 21 March 2025 12:1221.03.2025 12:12
RV wrote:
-------------------------------------------------------
Therefore => load M2

Where can I find that? I can't see it in the predefined setups. Is it only in VBAR VBASIC?
I found what's described here: https://www.youtube.com/watch?v=urZS6istnvE

All gyro parameters are set to zero there. But in E1CH1 ff, "FC Roll" ff is set as an input; to my knowledge, that should then be "Roll" ff.
I need to draw all of this out...

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
machine-translated from German · Show original
Eddi E. aus G. 21 March 2025 13:4521.03.2025 13:45
Hi,

VBasic, yes.

FC Roll would include agility (like Dual Rate), Expo, sensitivity (0 when 0), etc.
Roll would only be the stick; everything else would have to be configured in the external system.

Just once :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
RV 21 March 2025 14:5421.03.2025 14:54
Jürgen, that would be VBar Basic with the M2 as a "pure" receiver for other FBL.

She can unlock it for you...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
JMalberg 27 March 2025 17:4827.03.2025 17:48
Hey everyone,

So I went through the VBAR Pro again to make it "dumb".

Set up
-H1 or H3 depending on the FBL, but usually H1

Changed or reset to zero
-Main rotor
--Sensitivity = 0
--Lightness=0
--Pitch Pump=0
--Pitch Balance = 10
--Optimizer OFF

-tail rotor
--Sensitivity = 0
--Pendulum suppression=0
--Pitch precomp=0
--Cycl. Precomp=0
--Optimizer OFF

Result
The servos barely react, but the tail servo travel is too short. If I increase the sensitivity again, the tail servo travel is fine.
It seems that the VBAR lobotomy to VBASIC won't work out that way.

@RV: Could you please release the VBASIC for serial number 20050837?
Can I switch back to VBar Professional Rescue later without bothering you again?
It's all just meant as a test setup and backup, right?


Now to the SBUS connection:
I used the OMPMP2 macro cells as a starting point, but deleted everything except for 2 cells.
For the SBUS output on AUX1, I used your description https://www.vstabi.info/de/node/2129 with only a few adjustments for helicopters:

Channel 4 = Pitch curve input "MC28"
Channel 5 = Speed input "FC ESC" (Motor and safety switches are taken into account, no macro cell is needed)
Channel 18 = Motor Off/AR/On Input "SW Motor" (only additional if the third-party FBL requires it)

Macrocell 27: Sensitivity = Value per bank 1/2/3 Input "SW Bank"
Macrocell 28: Pitch curve for all banks Input Pitch (Too bad there is no "FC Pitch" with all its curves.)

I see no further use for any other OMPMP2 macrocells.

It works so far, and some things can be adjusted via the normal flight parameters.


Attached are the setup and the macrocells.

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )



Edited once. Last edited on March 27, 2025 at 5:50 PM by JMalberg. File attachments:
Open | Download - 11003990_vbar_VBASIC.zip (614 bytes)
Open | Download - 11003990_macro_SBUS_Demon3SX.zip (420 bytes)
machine-translated from German · Show original
RV 27 March 2025 20:4527.03.2025 20:45
Vbasic is installed and will be included in the update.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless