k.h.o.heli
30 August 2025 20:0530.08.2025 20:05
Hello Mikado team,
I need your support; I'm programming a surface model for the first time.
Model type: Hotliner
Features:
CH1 - HR
CH2 - QR links
CH3 - QR right
I assigned the throttle function to the pitch stick: Cell type - Curve / Input - MC10/ESC
1. Special function: QR should act as a brake via switch 3 (option 3), HR mixed in.
2. Special function: When motor switch 5 is in the OFF position (Pos.A), the throttle function should be deactivated (for safety).
Sender: VBCT evo
Software: VPlane
I've already spent several hours on this, read information and watched videos, but I couldn't find a solution.
Thank you for your help
Regards, Kurt
Hallo Mikado-Team,
brauche Eure Unterstützung, Programmiere zum ersten Mal ein Flächenmodell.
Modelltyp: Hotliner
Funktionen:
CH1 - HR
CH2 - QR links
CH3 - QR rechts
Die Gas-Funktion habe ich auf dem Pitch-Knüppel gelegt: Zellentyp - Kurve / Eingang - MC10/ESC
1.Sonderfunktion: QR sollen per Schalter 3 (Option 3) als Bremse wirken, HR beigemischt.
2.Sonderfunktion: Wenn Motor-Schalter 5 auf AUS steht (Pos.A) soll die Gas-Funktion deaktiviert sein (zur Sicherheit)
Sender: VBCT evo
Software: VPlane
Habe mich schon einige Stunden damit beschäftigt, Infos gelesen und Videos geschaut, konnte aber keine Lösung finden.
Danke für Eure Hilfe
Gruß Kurt
Dirtygeri
31 August 2025 10:0231.08.2025 10:02
Hello Kurt!
2. Special function - you don't need to program anything, it's already set up that way... Engine switch in OFF - "throttle" is OFF, regardless of the throttle stick position... If you're that worried, there's also the safety switch... As Rainer always says, belt and suspenders... :-)
1. Special function - this is like if you want to mix in the ailerons as flaps, only in the opposite direction (up instead of down), there are also great videos by Rainer about this...
Look... you'll find what you're looking for :-)
Best regards, Geri
Hallo Kurt!
2. Sonderfunktion - da brauchst du nix programmieren, das ist sowieso so .... Motorschalter auf AUS - "Gas" ist AUS, egal wo der (Gas-) Knüppel steht ... Wenn du so ängstlich bist, da gäbe es auch noch zusätzlich den Sicherheitsschalter ... Wie sagt Rainer immer dazu, Hosenträger und Gürtel ... :-)
1. Sonderfunktion - das ist so wie wenn du die Querruder als Klappen dazumischen willst, nur in die andere Richtung (rauf statt runter), da gibt es auch tolle Videos von Rainer ...
Schau mal .... du wirst fündig :-)
LG Geri
rutra
31 August 2025 10:2131.08.2025 10:21
k.h.o.heli
31 August 2025 18:4831.08.2025 18:48
Hello Geri,
I also thought that when the motor switch 5 is in the OFF position, the throttle stick is deactivated, but that is not the case.
Regardless of the position of the engine switch 5, the throttle is always active; I have also checked the safety switch 4.
It is activated (OFF) and yet the engine still runs ON.
Hallo Geri,
war auch der Meinung wenn der Motor - Schalter 5 auf AUS steht ist der Gas-Knüppel deaktiviert, dem ist nicht so.
Egal in welcher Stellung der Motor - Schalter 5 steht das Gas ist immer aktiv, auch den Sicherheits - Schalter 4 habe ich
aktiviert (AUS) und trotzdem läuft der Motor AN.
Fingolf
31 August 2025 19:5631.08.2025 19:56
Gas should be on ESC and not manually on a macro cell.
Change that, sb.
Stephan
Gas sollte auf ESC sein und nicht manuell auf einer Makro Zelle.
Änder das mal sb.
Stephan
Dirtygeri
1 September 2025 10:4301.09.2025 10:43
Hello Kurt!
Please connect the channels as intended -> ESC = Motor, Tail = Rudder, CH1 = Elevator, CH2 and CH3 = Ailerons, if I'm not mistaken...
I found an old, homemade guide for the additive that might help you...
LG Geri File attachments:
Open |
Download - VBAR-Ailerons-as-Flaps.zip (350.6 KB)
Hallo Kurt!
Bitte die Kanäle so anschließen wie vorgesehen -> ESC = Motor, Tail = Seitenruder, CH1 = Höhe, CH2 und CH3 = Quer, wenn ich mich jetzt nicht irre ...
Für die Beimischung habe ich noch eine alte, selbst gebastelte Anleitung gefunden, die dir helfen kann ...
LG Geri
Dateianhänge:
öffnen |
Download -
VBAR-Querruder-als-Landeklappen.zip
(350.6 KB)
k.h.o.heli
2 September 2025 01:4402.09.2025 01:44
Hello Geri,
I followed your instructions, and after a few tries it worked.
First, I removed the gas function from the macrocell, as Stephan advised.
The engine off function and the safety function are now correctly set.
Programming a surface model with the Mikado system is a
A real challenge; I couldn't have done it alone. Thank you so much for your help.
Many thanks to everyone else for the quick support.
Regards, Kurt
Hallo Geri,
bin nach Deiner Anleitung vorgegangen, nach einigen Versuchen hat es funktioniert.
Hab zuerst die Gas-Funktion aus der Macrozelle entfernt, wie von Stephan geraten.
Die Motor - AUS Funktion und die Sicherheit - Funktion sind jetzt richtig eingestellt.
Die Programierung eines Flächenmodells mit dem Mikado-System ist eine
echte Herausforderung, alleine hätte ich das nicht geschafft. Vielen Dank für die Hilfe,
auch allen Anderen vielen Dank für die schnelle Unterstützung.
Gruß Kurt
Eddi E. aus G.
2 September 2025 09:0602.09.2025 09:06
Hi Kurt,
Well, I think it's (perhaps too...) easy :-)
Model setup
. configure everything there, for the respective connections, control surface type, mixing ratios, drive
. go flying
It has everything you need for a 4-flap model with a motor; I don't even need to know the word "macrocell"...
Motor switches and safety switches are always active on the connection for the drive, regardless of whether it's a helicopter, fixed-wing aircraft, or something else.
You wouldn't start any transmitter by programming a model from scratch with free mixers...
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Kurt,
also ich finde ja, es ist (vielleicht zu ...) einfach :-)
. Modellsetup
. alles dort einstellen, für die jeweiligen Anschlüsse, Steuerflächentyp, Mischanteile, Antrieb
. fliegen gehen
Da ist alles drin für ein 4-Klappen-Modell mit Antrieb, da brauche ich noch nicht mal das Wort Makrozelle zu kennen ...
Motorschalter und Sicherheitsschalter sind immer auf dem Anschluss für den Antrieb aktiv, egal ob Heli oder Fläche oder-oder.
Man würde bei jedwedem Sender ja auch nicht damit anfangen, ein Modell von Grund auf mit freien Mischern zu programmieren ...
Grüßle
Eddi
Born to fly ...
forced to work.
k.h.o.heli
17 September 2025 20:1917.09.2025 20:19
Hi Eddi,
I still need help!
Initial situation:
Sender: VBCT evo
Software: VPlane
Electric gliders: 2QR / 1HR
I have made the following settings:
Surface Mixer Setup
Flap type: Transverse
Output slot CH2
Output min / max -35 / 50
Cross Mix 100
Flap Mix 50
Flap type: Transverse
Output slot CH3
Output min / max -50 / 35
Cross Mix 100
Flap Mix 50
Macrocells:
MC09 / Flap
Cell type: Channel
Input Signal: MC11 / E1CH1
Limit min / max: -120 / 120
Distance min / max: -120 / 120
Rate of change: 3
MC11 / E1CH1
Cell type: 3-level
Entrance: Sw Op 3
Exit down: 0
Starting average: 60
Output up: 120
With these settings (function and rudder deflection), the setup is OK.
Now my problem: I use the QR code as a brake, when activating it
Switch 3 (Sw Op 3) moves the QR upwards and the HR slightly
downwards. However, the aileron deflection is too small for me when I use the flap mix.
Changing the value to 50 does nothing.
How do I solve this problem?
Many thanks for your support
Regards, Kurt
Hallo Eddi,
brauche noch Hilfe!
Ausgangslage:
Sender: VBCT evo
Software: VPlane
E-Segler: 2QR / 1HR
Folgende Einstellungen habe ich vorgenommen:
Flächenmischer Set Up
Klappentyp: Quer
Ausgabe Steckplatz CH2
Ausgabe min / max -35 / 50
Quer Mix 100
Klappen Mix 50
Klappentyp: Quer
Ausgabe Steckplatz CH3
Ausgabe min / max -50 / 35
Quer Mix 100
Klappen Mix 50
Makrozellen:
MC09 / Flap
Zellentyp: Kanal
Eingang Signal: MC11 / E1CH1
Limit min / max: -120 / 120
Weg min / max: -120 / 120
Änderungsrate: 3
MC11 / E1CH1
Zellentyp: 3-Level
Eingang: Sw Op 3
Ausgang nieder: 0
Ausgang mittel: 60
Ausgang hoch: 120
Mit diesen Eingaben (Funktion und Ruderausschlag) ist das Set Up O.K.
Nun mein Problem: die QR verwende ich als Bremse, beim betätigen
des Schalters 3 (Sw Op 3) fahren die QR nach Oben und das HR etwas
nach Unten. Der Ruderausschlag der QR ist mir aber zu wenig, wenn ich den Klappen Mix
Wert 50 verändere passiert nichts.
Wie löse ich das Problem?
Vielen Dank für Deine Unterstützung
Gruß Kurt
Eddi E. aus G.
18 September 2025 09:5918.09.2025 09:59
Good morning,
What does the MC11 have to do with this...?
Which model setup did you use as a basis?
Even if there are only 2 QR codes, if I want to use the flap function on them, I would use the standard + flaps as a basis. Then I can use the flap function MC09 and MC27 (long click on CH2) in the setup, for example, and don't have to reprogram anything manually – even if no flaps are physically installed or connected.
Just tried it, it works, it has both the QR deflection and the programmed flap deflection.
No MC11...
Grüßle
Eddi
Born to fly ...
forced to work.
2 mal bearbeitet. Zuletzt am 18.09.2025 11:14 von Eddi E. aus G..
Moin,
was hat die MC11 da zu tun ..?
Welches Modellsetup hast Du als Grundlage genommen?
Auch wenn nur 2 QR, aber wenn ich die Klappenfunktion darauf nutzen möchte, würde ich Stand. + Klappen als Basis nehmen, dann kann ich im Setup die Klappen-Funktion MC09 und MC27 (Langklick auf CH2) bspw. nutzen, und muss nix händisch nachprogrammieren – auch wenn physisch keine Klappen eingebaut, angeschlossen sind.
Eben probiert, tut, hat sowohl den QR-Ausschlag als auch den programmierten Klappen-Ausschlag.
Keine MC11 ...
Grüßle
Eddi
Born to fly ...
forced to work.
2 mal bearbeitet. Zuletzt am 18.09.2025 11:14 von Eddi E. aus G..
k.h.o.heli
18 September 2025 11:0218.09.2025 11:02
Hi Eddi,
Thanks for the quick information, I'll look into it this weekend.
Regards, Kurt
Hallo Eddi,
Danke für die schnelle Information, werde mich am Wochenende damit beschäftigen.
Gruß Kurt
k.h.o.heli
24 September 2025 11:4724.09.2025 11:47
Hello everyone,
I still haven't managed to program my model.
The more I adjust, the less it fits. First, make a few.
Take a few days off. I'll be in touch again.
Regards, Kurt
Hallo zusammen,
hab es immer noch nicht geschafft mein Modell zu programmieren.
je mehr ich einstelle desto weniger passt es. Mache erst mal ein paar
Tage Pause. Melde mich wieder.
Gruß Kurt
Eddi E. aus G.
24 September 2025 13:2924.09.2025 13:29
Good morning,
When you have the mental space again: where is the problem?
Height, side, lateral, drive already?
Or only at the flaps?
Of course, if you've messed things up and want to start over, the following is important:
Delete macro cells
New setup
If necessary, we can also do supervised hiring over the phone; we would just need to arrange something.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
wenn Du wieder den Kopf dafür frei hast: wo klemmt es denn?
Höhe, Seite, Quer, Antrieb bereits?
Oder erst bei den Klappen?
Wichtig, wenn man sich erst einmal verdaddelt hat und neu anfangen möchte, ist natürlich:
. Makrozellen löschen
. Neues Setup
Wir können im Zweifel auch Betreutes Einstellen am Telefon machen, müssten nur was ausmachen.
Grüßle
Eddi
Born to fly ...
forced to work.
k.h.o.heli
29 September 2025 19:3929.09.2025 19:39
Hi Eddi,
Thank you for the offer and for your patience.
Here's another attempt.
Basis: Model setup - Standard + Flaps
Surface Mixer Setup
Valve type: Flaperon
Output slot CH2
Output min / max -38 / 42
Cross Mix 100
Flap Mix 120
Valve type: Flaperon
Output slot CH3
Output min / max -42 / 38
Cross Mix 100
Flap Mix 120
MC09 / Flap
Cell type: Channel
Input Signal: MC27
Limit min / max: -120 / 120
Distance min / max: -120 / 120
Rate of change: 3
MC27
Cell type: 3-level
Entrance: Sw Op 3
Exit down: 0
Starting average: 60
Output up: 120
With these settings, QR and HR readings are correct.
The problem: I use the QR code as a brake; when activating it...
The QR does not move far enough upwards when switch 3 (SW OP 3) is activated.
How can I make the rash bigger?
Many thanks for your support
Regards, Kurt
Hallo Eddi,
Danke für das Angebot und für die Geduld.
Hier nochmal ein Versuch
Grundlage: Modellsetup - Standart + Klappen
Flächenmischer Set Up
Klappentyp: Flaperon
Ausgabe Steckplatz CH2
Ausgabe min / max -38 / 42
Quer Mix 100
Klappen Mix 120
Klappentyp: Flaperon
Ausgabe Steckplatz CH3
Ausgabe min / max -42 / 38
Quer Mix 100
Klappen Mix 120
MC09 / Flap
Zellentyp: Kanal
Eingang Signal: MC27
Limit min / max: -120 / 120
Weg min / max: -120 / 120
Änderungsrate: 3
MC27
Zellentyp: 3-Level
Eingang: Sw Op 3
Ausgang nieder: 0
Ausgang mittel: 60
Ausgang hoch: 120
Mit diesen Einstellungen passen QR und HR Ausschlag.
Das Problem: die QR verwende ich als Bremse, beim betätigen
des Schalters 3 (SW OP 3) fahren die QR nicht weit genug nach Oben.
Wie kann ich den Ausschlag vergrößern?
Vielen Dank für Deine Unterstützung
Gruß Kurt
Eddi E. aus G.
30 September 2025 09:2030.09.2025 09:20
Good morning,
Looking at the aileron min/max settings, I think you need to adjust them so that you achieve the desired deflection (min/middle/max) with the flap function (without ailerons, mix initially set to 0), possibly also adjusting mechanically (servo arm center, perhaps even one hole further out, or one hole further in on the rudder, whichever is easier or even possible).
Then adjust the cross-mixer (only) as high as you need it (around 40% if you could transfer it to the current min/max values), but also make sure that nothing mechanically engages, balance if necessary.
At the moment, you need to limit the aileron servo travel so that not much is left for the flaps (in layman's terms, 120% of 40% would be 48%; depending on where the center is, the total travel may be shifted a little further, but not by much).
The approach (thought about it the other way around) is then a flap with aileron mixing, but the result (movement) is the same.
Ah, helicopters are so simple ^^
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
wenn ich Quer min/max so sehe, glaube ich, Du musst da so nacharbeiten, dass Du mit der Klappenfunktion (ohne Quer, Mix erst mal 0) den gewünschten Ausschlag erreichst (min/Mitte/max), ggfs. auch mechanisch anpassen (Servoarm Mitte, ein Loch weiter außen vielleicht sogar, oder am Ruder eins weiter innen, was einfacher ist bzw. überhaupt geht, falls).
Dann den Quer-Mixer (nur) so hoch einstellen, wie Du es brauchst (rund 40 % wenn man es auf die jetzige min/max Werte übertragen könnte), aber auch drauf achten, dass mechanisch nix angeht, ggfs. austarieren.
Im Moment musst Du den Servoweg Quer mMn so begrenzt, dass für die Klappen anteilig nicht viel übrig bleibt (laienhaft, 120 % von 40 % wären 48 %, je-nachdem wo die Mitte ist ist der Gesamtweg evtl. noch etwas weiter verschoben aber eben auch nicht viel).
Der Ansatz (anders rum gedacht) ist dann eine Klappe mit Querruder-Beimischung, das Ergebnis (Bewegung) ist aber das selbe.
Hach, Hubschrauber sind so einfach ^^
Grüßle
Eddi
Born to fly ...
forced to work.
k.h.o.heli
1 October 2025 10:2001.10.2025 10:20
Hi Eddi,
You're right, helicopters are so simple. I've built three helicopters with the Mikado system in the last two years.
It was programmed and configured, and there were absolutely no problems; I was and still am thrilled.
I will be making mechanical modifications to my electric glider.
Thanks again for your support!
Regards, Kurt
Hallo Eddi,
Du hast Recht, Hubschrauber sind so einfach. Habe in den letzten 2 Jahren 3 Helis mit dem Mikado-System
programmiert und eingestellt, und es gab überhaupt keine Probleme, ich war und bin begeistert.
Bei meinem E-Segler werde ich mechanische Änderungen vornehmen.
Nochmals Danke für Deine Unterstützung!
Gruß Kurt