← VPlane / VBasic VLink

Macrocell support for skydivers translated

VBar › VPlane / VBasic VLink · Started by Dirtygeri on 7 November 2025 13:1207.11.2025 13:12
Dirtygeri 7 November 2025 13:1207.11.2025 13:12
Hello Rainer!

I need your help with my RC Skydiver, as I obviously can't see it... ???

Basically, each servo controls one arm of the jumper, requiring the entire servo travel in each case.

Resting position - no control input, right and left arm/servo in 90 degree position
Roll right or left input, right or left arm moves up to approximately 45 degrees downwards (flying a turn) = Half servo travel
Pulling the pitch stick (from center to bottom), both arms move to approximately 0 degrees at full deflection (pitch fully pulled) = full servo travel

See the manufacturer's video at minute 14:15... Video Link

My approach to programming

CH3 = Re Arm = Mixer of cell 14 (Roll Re Curve / Re Arm Half) and cell 18 (Pitch Pull / Re Arm Full)
Cell 14 = Curve with the points for ROLL input RE (servo travel half)
Cell 18 = Curve with the points for NICK input Drag (Servo travel full)

I'll spare us the left arm here, since we'll implement it right away...

Result:
Everything basically works, but I only get full servo travel when the stick is in the bottom right corner. With full pull on the pitch stick, I lose (some) servo travel...

Where is my mistake? It seems to be the mixing ratio... I'm completely baffled...

Attached are images, and the VPlane Basic and Macrocells files are also included in the ZIP file...

Many thanks for your support!
Geri



Edited twice. Last edited on 07/11/2025 at 16:15 by Dirtygeri.

File attachments:
Open | Download - SKYDIVER.zip (199.6 KB)
machine-translated from German · Show original
Dirtygeri 7 November 2025 13:1307.11.2025 13:13
Addendum with the remaining macrocell images...

machine-translated from German · Show original
RV 7 November 2025 23:5107.11.2025 23:51
The problem is (see bars in MC overview) that the value at rest is -80. Therefore, not enough percentages are achieved in the end.

But... there's a solution!

Simply connect the same input twice to the output mixer - the percentages will then add up...

Regards (EN) / Greetings (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Please use a PC and a proper keyboard for posts and replies, and answer all questions completely. Take your time and answer follow-up questions thoroughly and completely.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
For individual communication, please use email exclusively ! - Private messages, messenger, chat, etc. will not be processed.
For single user communication please send an email only ! PM, Messenger, Chat etc. won't be read.


machine-translated from German · Show original
Dirtygeri 8 November 2025 07:4408.11.2025 07:44
Good morning Rainer!

Thank you so much for your night shift :-) Brilliantly simple, simply brilliant 8-) !!!

I have one last small request: Could you add the words " Springer " and " Schutz " to the talking switches Pro? Sure, "Modell" works too, but it would be nicer that way... If not, because there aren't enough users, that's no problem either!

Anyway, thank you very much & have a nice, well-deserved weekend!!!
Best regards, Geri
machine-translated from German · Show original
RV 8 November 2025 07:4508.11.2025 07:45
One more tip:

It's best to connect a channel macro cell to the socket where the output is located and turn the paths and limits all the way up.
This is "operated" by the aforementioned output mixer.

Advantage: Each servo can be trimmed and its endpoints set separately. Failsafe definition is also possible (otherwise it's held).

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Dirtygeri 8 November 2025 07:5508.11.2025 07:55
Oh yes, thank you, I'll incorporate that. It works well because I'm also adding a safety feature so that pitch/roll only work when the switch is in the "motor on" position... It would be bad if the paratrooper was already waving his arms while still attached to the plane/helicopter...

Anyway, thank you so much! Geri
machine-translated from German · Show original
RV 9 November 2025 21:5709.11.2025 21:57
And about the language... update it!

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless