Mario Frascoia
10 January 2026 13:4710.01.2026 13:47
Hello everyone,
I just can't seem to program my ailerons upwards for landing (as brakes), I've already tried for 3 hours.
I use a VBar Neo and a VBar Control Touch Evo.
My model setup is: Standard + Flaps.
Does he provide instructions for this?
Regards, Mario
Hallo zusammen,
ich schaffe es einfach nicht meine Querruder für die Landung ( als Bremse ) nach oben zu programmieren, habe schon 3 Stunden probiert.
Ich verwende ein V Stabi Neo und eine V Bar Control Touch Evo.
Als Modell Setup habe ich: Standard + Klappen.
Gibt er hierfür eine Anleitung ?
Gruß Mario
RV
10 January 2026 22:4010.01.2026 22:40
Hi Mario,
Please no thread hijacking - I've split it off.
If you want to position the QR code facing upwards, you must enter the input as follows:
MC09 is the "input cell" for the wing mixer for the ailerons. It normally contains a channel with a delay. As far as I know, this is controlled by MC20 (or MC27?) as a 3-level switch (LK switch).
Now do the following:
- MC 09 becomes a mixer, input 1 e.g. MC21, input 2 MC22
- MC 21 includes the channel as above on 09 with the LK Delay.
MC 22 is now the input for your specific case. You can then configure it as you see fit (3 levels, switches, delay, joysticks - whatever is needed).
Should you also want to set the QR in parallel - here you place an MC with a mix on itself at the QR outputs (QR goes through), 2. crochet the mix input as above.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hallo Mario,
bitte kein Threadnapping - ich habs abgespalten.
Wenn Du die QR nach oben anstellen möchtest dann musst Du den Input dazu wie folgend machen:
MC09 ist die "Eingabezelle" für den Wingmixer zum QR. Da ist normalerweise ein Channel mit Delay drin. Dieser wird AFAIK von MC 20 (oder 27?) als 3-Level (Schalter LK) bedient.
Nun mach folgendes:
- MC 09 wird zu einem Mischer, Eingang 1 z.B. MC21, Eingang 2 MC22
- MC 21 beinhaltet den Channel wie oben zuvor auf 09 mit dem LK Delay.
- MC 22 ist nun der Eingang für Deinen Sonderfall. Hier dann nach eigenem Ermessen (3-Level, Schalter, Delay, Knüppel - was da auch immer da nötig ist) reinlaufen lassen.
Solltest Du parallel die QR dann auch stellen wollen - Hier dann an die QR Ausgänge eine MC mit Mix auf sich selbst setzen (QR geht durch), 2. Mixeingang wie oben verhäkeln.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Mario Frascoia
11 January 2026 19:3511.01.2026 19:35
Hello Mr. Vetter,
I'll try it, thank you very much.
Regards, Mario
Hallo Herr Vetter,
ich probiere es, vielen Dank
Gruß Mario