Epro500
25 August 2026 15:0325.08.2026 15:03
Hello,
I have a question about the limits:
When I program an e-glider via the setup menu, I set limits for the ailerons, for example, up and down. For instance, +/- 10 mm. If I then program a butterfly mixer, do I need an additional 10 mm of upward deflection and would I have to increase the aileron limit by 10 mm? Or is there another way?
Question 2: Is it generally possible to activate a mixer from multiple or two different switches?
LG
Erich
Hallo,
hätte eine Frage zu den Limits:
Wenn ich über setup einen eSegler programmiere stelle ich ja zB bei den Querrudern nach oben und nach unten Limits ein. ZB +/- 10 mm. Wenn ich jetzt zusätzlich einen Butterfly Mischer programmiere so benötige ich dann zusätzlich 10 mm nach oben und müsste das limit für die Querruder um 10 mm nach oben höher stellen. Oder gibt es eine andere Möglichkeit?
2.Frage: kann man einen Mischer grunsätzlich auch von mehreren bzw 2 verschiedenen Schaltern aus aktivieren?
LG
Erich
Eddi E. aus G.
25 August 2026 16:2925.08.2026 16:29
Hi Erich,
Correct. Output min/max specifies the maximum allowed value.
The maneuverability then determines the difference per bank (almost practically in percent).
The stabilization adds a little extra, as it works around the position of the control surface.
Mix proportions accordingly, up to min/max. That's it.
Just try figuring it out, you can see it directly on the model.
Regarding the second question, please describe in more detail what you are planning, and... why :-) ?
—Eddi
Born to fly ...
forced to work.
Moin Erich,
richtig. Ausgabe min/max. gibt das vor, was maximal 'ausgeschlagen' werden darf.
Die Wendigkeit bestimmt dann den Ausschlag je Bank (quasi-praktisch in Prozent).
Die Stabilisierung nimmt sich noch etwas dazu, arbeitet ja um die Stellung der Steuerfläche herum.
Mix-Anteile entsprechend, bis zu min/max. eben.
Einfach mal austüfteln, man sieht's ja direkt am Modell.
Zur 2. Frage, beschreibe bitte genauer, was Du vorhast, und ... warum :-) ?
—Eddi
Born to fly ...
forced to work.
Epro500
24 September 2026 18:5024.09.2026 18:50
Hi Eddi,
Sorry for the late reply.
Over the last few weeks I've flown a lot with the e-glider (F5K and 2.1m DjangoS) and worked out various values.
Considering I come from helicopters and am a beginner in gliding, the gliders with VBar fly incredibly well :-) the little F5K flies like it's on rails even at higher speeds :-) space-wise it's challenging, but worth every effort.
I think the usual different limitations on the upward/downward deflections are no longer so important in principle with VPlane.
For the macros, I was thinking more along the lines of the butterfly position on the throttle stick (adjustable) with the engine off.
You do have general instructions, but to be honest, I don't understand enough about the exact implementation…
Is there perhaps a tutorial with screenshots for this? :-) I would be very grateful if I wanted to implement it.
LG
Erich
Hallo Eddi,
Sorry für die späte Rückmeldung.
Bin in den letzten Wochen viel mit dem eSegler (F5K und 2,1m DjangoS) geflogen und verschiedene Werte ausgetüftelt.
Für das, dass ich von den Helis komme und beim Segelfliegen Anfänger bin fliegen die Geräte mit VStabi doch wahnsinnig gut :-) der kleine F5K fliegt wie auf Schienen selbst bei höheren Geschwindigkeiten :-) platztechn zwar heruasfordernd, aber jede Aufwand wert.
Denke die üblichen unterschiedlichen Limitierungen der Ausschläge nach oben/unten sind bei VPlane prinzipiell nicht mehr so wichtig.
Bei den Makros habe ich eher an sowas gedacht wie die Butterflystellung am Gasknüppel (verstellbar) mit Motor aus.
Ihr habt zwar eine allgem Anleitung dazu aber ehrlichgesagt für die genaue Umsetzung blicke ich zu wenig durch…
Gibt es hier vielleicht eine Anleitung mit den Screenshots dafür. :-) wäre sehr dankbar dafür falls ich es umsetzten möchte.
LG
Erich
Eddi E. aus G.
25 September 2026 09:3625.09.2026 09:36
Hi Erich,
I'm already looking forward to it!
Regarding BF, I could just look at Rainer's explanations in Start-Stop-Start and try to replicate them, but I don't have anything ready to show it more clearly than with servos on the table.
I am quite sure (even as a complete non-computer user) that it works just as well with the Touch/EVO, the logic and menus are the same as with the Classic, and you can even name the cells, which greatly simplifies finding them later.
Simply put, without any unnecessary details: the outputs for the respective control surfaces are multiplexed. When the engine is idling and running, these multiplexers have the original function as their input (e.g., CH2 to CH2, CH3 to CH3, etc.). When the engine is off, a mixer is used between the original function and a cam module, which in turn has the throttle stick as its input. The cam module then allows you to adjust the direction of rotation and the mixing ratio to match the stick position.
For control surfaces that have the same signs, you can possibly use the same strand as the input; for those that don't, you would have to crochet one separately for each.
If desired, the switching between throttle and foot-first could also be controlled by a trigger cell that differentiates between throttle (0-100) and foot-first (0-100) from the switching point (trigger greater than or equal to one does this, less than or equal to another) at the stick's midpoint. This would again require multiplexers (the trigger being the input) and curves (direction/mixing ratio/stick position).
Simply save your current state (setup and macro cells) so you can always return to it, and then grab a control surface to practice with... have fun and good luck!
—Eddi
Born to fly ...
forced to work.
Hi Erich,
freut mich schon mal!
Zu BF könnte ich jetzt auch nur Rainers Ausführungen in Start-Stop-Start anschauen und nachstellen, hab aber auch grad nix fertig da stehen, um es anschaulicher als mit Servos auf dem Tisch zu zeigen.
Dabei bin ich mir (auch als absoluter nicht-Flächi) ziemlich sicher, dass das mit der Touch/EVO genauso gut geht, die Logik und die Menüs sind ja die selben wie bei der Classic, und man kann sogar die Zellen noch benennen, was das spätere Wiederfinden super vereinfacht.
Ganz stumpf und ohne zu spickeln: auf die Ausgänge für die jeweiligen Steuerflächen Multiplexer, die bei Motor Leerlauf und An die Originalfunktion als Eingang haben (bspw. CH2 auf CH2, CH3 auf CH3 etc.), und bei Motor Aus einen Mischer zwischen der Originalfunktion und einer Kurvenzelle, die wiederum den Gasknüppel als Eingang hat. Mit der Kurvenzelle kann man dann die Laufrichtung und den Mischanteil passend zur Knüppel-Position hinbiegen.
Für Steuerflächen, für die die selben Vorzeichen gelten, kann man u. U. den selben Strang als Eingang nehmen, für-die-wo-nicht müsste man halt jeweils separat einen häkeln.
Wenn man wollte, könnte man die Umschaltung zwischen Gas und BF auch noch über eine Trigger-Zelle laufen lassen, die ab Schaltpunkt (Trigger größer gleich macht dies, kleiner gleich macht jenes) Knüppelmitte zwischen Gas (0...100) und BF (0...–100) unterscheidet. Dazu braucht's dann auch wieder Multiplexer (Eingang ist der Trigger) und Kurven (Richtung/Mischanteil/Knüppel-Position).
Speichere einfach mal den jetzigen Stand (Setup und Makrozellen), so dass Du immer wieder dorthin zurück kannst, und dann schnapp Dir einfach mal eine Steuerfläche zum Üben ... viel Spaß und gutes Gelingen!
—Eddi
Born to fly ...
forced to work.
Epro500
4 October 2026 19:2404.10.2026 19:24
Thanks for your support, Eddi!
I haven't needed flaps so far anyway. I'll set up some servos for testing over the winter…
LG
Erich
Danke für Deinen Support Eddi!
Bis jetzt benötigte ich ohnehin keine Klappen. Werd mal im Winter Servos zum testen entsprechend aufbauen…
LG
Erich
Eddi E. aus G.
5 October 2026 10:4205.10.2026 10:42
Good morning,
gladly!
I would try it directly on the model, that way you can clearly see what happens. Remove the propeller, or use a servo as a pointer instead of the speed controller.
As I said, save the setup and macrocell setup beforehand so that you can always go back to it.
Gutes Gelingen!
Eddi
Born to fly ...
forced to work.
Moin,
gern!
Ich würde es ja direkt am Modell probieren, da sieht man schön, was passiert. Prop ab, oder statt Regler ein Servo an ESC als Zeiger.
Wie gesagt, halt vorher Setup und Makrozellen Setup speichern, so dass man da immer wieder zurück kann.
Gutes Gelingen!
Eddi
Born to fly ...
forced to work.