← VBar NEO/EVO VLink

Large scale helicopters

VBar › VBar NEO/EVO VLink · Started by GlenDavis1971 on 7 October 2026 11:5307.10.2026 11:53
GlenDavis1971 7 October 2026 11:5307.10.2026 11:53
Hi

I am planning on building a large scale helicopter and want to use the EVO.

Can the EVO cope with a model nearly 3m long and weighing possibly 35kg?

Is there a way to get 2 EVO's to work as a pair for redundancy should one fail?

Also any other suggestions you may have for a very big model 1/8 scale CH53

Many Thanks

Glen
RV 7 October 2026 12:1307.10.2026 12:13
Hi Glen,

my Huey has 2.4m and 22kg.

I would start with a VBar EVO as Master and a second one as Slave (Slave gives you 2 more antennas and more servo sockets).

Feed the RC power directly, probably through 4 simple diodes in parallel, use 12V servos and no switch. Also use 2 100F Buffers. Just like i did on the Huey. Keep it simple.

If you were looking for redundancy - you have to answer the question ... if one sensor might point a wrong value - how do you decide which is the right one? - So a true redundancy comes with 3 units and a voting system on top - like manned aircraft do.

Consider - it is just a hobby - and the cost of a system described above would be way too expensive. And at least - the voting system is also a single point of failure ;-(

Just go for this scheme:

https://www.vstabi.info/forum/read.php?10,172594,page=8



regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




2 mal bearbeitet. Zuletzt am 07.10.2026 12:35 von RV.
Eddi E. aus G. 7 October 2026 12:1807.10.2026 12:18
Hi Glen,

no worries about the size and weight. Check this out, Gerhard Pahl has been using VBar Control and VBar NEO and now EVO for years, and he even builds giant turbine helis turn-key bind-and-fly for customers, a bit like a bind and fly LOGO 200 (but not quite ^^).

Almost all ideas can be found here ... it's 'just' a 2.5 m 25 kg, but everything from building through outfitting to setting up as well as maintenance and upgrading is covered.

Long read, but definitely worth it!

Best,

Eddi

Born to fly ...
forced to work.
Max8200 7 October 2026 14:4807.10.2026 14:48
Just a bit more than half of your size but maybe I might jump in for a small cross question with the same outcome?

If you use two EVOs, is one always the Master (expected the one with the ESC input, swashplate- and tail servos) and the other one always the slave or are at least the sensors/antennas swapping after each use (like in real aviation)?

If not:
Do both EVOs requiring the same software in relation to Pro/Rescue or is only the master required to have the "full option" and the slave can be a "normal" EVO express?

Brgds
Lars

Viele Grüße,
Lars
RV 7 October 2026 14:5307.10.2026 14:53
The slave will get a special "Servo Extender" firmware. A EVO with VBasic is ok as an entry point.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Eddi E. aus G. 8 October 2026 09:2208.10.2026 09:22
Hi,

additionally, yes, the Master (Pro-/+Rescue VBar EVO) will always be that, use it's sensors and software, while the Slave EVO (Extender firmware) adds it's receiver/antennas and additional servo ports.

Then, it's part of both: while the receivers work with full redundancy (system always uses the best pair of any one of two antennas in the transmitter and any of the four or six antennas on the model, depending on orientation and other factors), there's still a possible single point of failure if you want to call it that, the Slave EVO can not take over flight control/swap those duties every other flight, or in an emergency.

Intellectual game, if you wanted that, it would also make sense to lay out everything else redundantly, and with the possibility to switch between the flight controls and their electrical connections totally, in case of a hard failure of one of the subsystems or in their respective power supplies. Maybe even have redundant actuators for all flight controls (no manual control backup, obviously ...), and have an independent and also redundant instance managing that, and with redundant and independent or backup power supply for all, managed, too.
And even then, every so often there's probably that one situation you didn't think of ahead ... or good old human error.

—Eddi

Born to fly ...
forced to work.
VStabi VStabi Pioneer of Flybarless