nurmalso
12 November 2019 18:1112.11.2019 18:11
Please hold on tight. I was finally able to read out the last reason for the shutdown, thanks to a tip from Turbinesolutions.
"low RPM - 29000"
Since the turbine was certainly not below 30,000 RPM during operation, which would be a reason for shutdown, but was actually running at full speed due to full pitch input, I wiggled the sensor cable and one flight later it did not shut down.
I'll replace the sensor cable and observe it for a while...
I could... I could... the thing has 19 hours on the clock and well... the previous owner had secured everything so extremely with cable ties that nothing could move, and even fixed the connector to the ECU with hot glue... and ultimately, the movement that's inherent in a model has to go somewhere...
Edith says: I had already reduced all the cable ties to a minimum when I overhauled the power supply, but I didn't expect that a cable would already be damaged. I hope that's all it is. If it shuts off again – with a new cable – I'll send it in for service. Then it'll just need a new RPM sensor.
Edited once. Last edited on 12/11/2019 at 18:22 by nurmalso.
Festhalten bitte. Ich konnte endlich den letzten Abstellgrund auslesen, nach einem Tip von Turbinesolutions.
"low RPM - 29000"
Da die Turbine im laufenden Betrieb sicher nicht unter 30.000 UPM war, was ein Abstellgrund wäre, sondern gerade am Hochtouren wegen Vollpitcheingabe war, hab ich mal am Sensorkabel gewackelt und einen Flug später stellte sie nicht ab.
Ich tausche das Sensorkabel und beobachte das eine Weile...
Ich könnte .... könnte ich... das Teil hat 19 Stunden auf der Uhr und naja... der Vorbesitzer hatte da mit Kabelbindern alles so extrem fixiert, dass sich auch ja nix bewegen konnte, dazu noch den Stecker mit Heisskleber an der ECU fixiert... und letztlich muss die Bewegung, die es in einem Modell nunmal gibt, irgendwo hin...
Edith sagt: Die ganzen Kabelbinder hatte ich beim Überarbeiten der Stromversorgung bereits auf ein Minimum reduziert aber dass da schon ein Kabel einen Knacks hat, hatte ich nicht erwartet. Ich hoffe, das wars auch. Wenn sie nochmal - mit neuem Kabel - abstellt, schick ich sie zum Service. Dann muss da eben ein neuer RPM Sensor rein.
1 mal bearbeitet. Zuletzt am 12.11.2019 18:22 von nurmalso.
RV
12 November 2019 23:2012.11.2019 23:20
Oha! - da wäre ich aber froh wenn das die Ursache ist. Ich bin dann gespannt wie es weitergeht, denn abstimmen kann man ja erst wenn man sich auf die Turbine verlassen kann.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nurmalso
18 November 2019 11:3818.11.2019 11:38
Hi Rainer,
I have a tip from the ECU manufacturer, who says that the rotor downwash can, under certain circumstances, blow out the turbine or "suck out" the flame, thus causing it to shut down.
After a pitch input, there is a release of pressure, consequently the controller reduces the throttle.
I am supposed to set the minimum throttle so that "hover gas" represents the lower limit in flight.
Now my question is, can I assign the corresponding value, base gas, to a potentiometer in order to adjust it during flight?
Thanks and regards
Markus
Moin Rainer,
ich hab 'n Tip vom Hersteller der ECU, der meint, der Rotorabwind kann unter Umständen die Turbine ausblasen bzw. die Flamme "heraus saugen" und so zum Abstellen führen.
Nach einer Pitcheingabe folgt ja eine Entlastung, folglich nimmt der Regler Gas raus.
Ich soll das minimale Gas so einstellen, dass "Hovergas" die untere Grenze im Flug darstellt.
Nun meine Frage, kann ich den entsprechenden Wert, Basisgas, auf ein Poti legen, um das im Flug an zu passen?
Danke und Grüße
Markus
RV
18 November 2019 20:5018.11.2019 20:50
Basisgas ist NICHt die untere Regelgrenze - das Gasminimum (Min Limit) ist die untere Regelgrenze.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nurmalso
19 November 2019 17:1219.11.2019 17:12
Good morning,
So, the gas minimum at hover speed is now 57%, previously 39%.
Unfortunately, it got dark and I was only able to test it for one flight. No way to turn it off.
Feel free to check my cloud, for regulatory reasons. I'll still experiment with the sensitivity, but it's working quite well as it is.
Now I need a few flights without any delays, for confidence... and better weather. I don't want to wait until March either. :-)
Edited once. Last edited on 19/11/2019 at 17:12 by nurmalso.
Moin,
so, Gasminimum ist nun bei Schwebedrehzahl auf 57%, vorher 39%,
leider wurde es dunkel und ich konnte das nur einen Flug lang testen. Kein Absteller damit.
Kannst gern in meine Cloud schauen, der Regelung wegen. Ich werd' noch mit der Empfindlichkeit experimentieren aber ansich läuft das so schon ganz gut.
Nun brauch ich n paar Flüge ohne Absteller, fürs Vertrauen... und besseres Wetter. Warten bis März will ich auch nicht. :-)
1 mal bearbeitet. Zuletzt am 19.11.2019 17:12 von nurmalso.
nurmalso
1 December 2019 13:2101.12.2019 13:21
So, here's some feedback. After trial and error, I continued searching for the reasons for the persistent engine shutdowns. Turbinesolutions was no help; the crucial tip came from Gaspar Espielle, who distributes the ECU. I also provided him with a log file, and he said it all looked like the shutdowns were due to fuel starvation, and asked if there was air in the fuel system.
No, of course not. But I then ordered and installed a new cable set and a new pump... the problem hasn't reappeared so far.
The cables appear to be fine, and the pump runs without problems on the workbench, not even overheating for hours. However, it seems to struggle with certain flight maneuvers or performance demands and briefly shuts down.
How could anyone come up with something like that... well.
I'll test how far I can reduce the minimum throttle setting to get rid of the "gov is at the lower limit" message when the weather is good. First, I finally need to get to the Vstabi setup.
Thanks so far!
So, mal ein feedback. Nach try and error weiter nach Gründen für immernoch vorhandene Absteller gesucht. Turbinesolutions war keine Hilfe, der entscheidende Tip kam von Gaspar Espielle, der die ECU vertreibt... ihm habe ich ebenfalls ein Log zur Verfügung gestellt und er sagte, das alles sieht nach Absteller wegen Spritmangel aus, ob ich Luft im Tanksystem hätte...
Nein, natürlich nicht. Aber ich habe dann einen neuen Kabelsatz und eine neue Pumpe bestellt und eingebaut... Problem taucht bisher nicht wieder auf.
Augenscheinlich sind die Kabel OK, die Pumpe läuft ebenfalls problemlos auf der Werkbank.. wird auch über Stunden nicht heiss. Dennoch scheint sie bei bestimmten Flugmanövern oder Leistungsanforderungen nicht klar zu kommen und stellt kurz mal den Betrieb ein.
Wie soll man auf sowas kommen.... nunja.
Inwieweit ich mit dem Mindestgas wieder runter kann, um von der Meldung "gov ist an der unteren Regelgrenze" weg zu kommen, werd ich bei gutem Wetter ausprobieren. Erstmal muss ich nun endlich ans Setup der Vstabi.
Danke soweit!
RV
2 December 2019 20:1202.12.2019 20:12
Okeee ... übrigens hat sich der Kollege aus UK noch nicht bei mir gemeldet, mal sehen ob und wann sich was tut.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nurmalso
5 January 2020 17:0405.01.2020 17:04
We are practically not taking a winter break this year, so there are now a few flights without any layovers.
I haven't done any fine-tuning yet, cold fingers are annoying, but you're welcome to take a look at the settings in my cloud.
The NEO occasionally complains about "lower limit" in the log, but I'll leave it as is for now. I'll definitely test what happens if I lower the limit a bit in the summer, but for the moment I need to build more confidence in the helicopter. :-)
Regarding the other thread about the switches (LS/rescue), I'll need to find some quiet time to work that out. Whenever I get the helicopter off the shelf at home, my 2 1/2-year-old is immediately there, fiddling with everything with his little screwdrivers... so I can't do that :-)
Conclusion to date - no shutdowns. The pump was the culprit. However, the old pump continues to run on a brushed controller and will serve as a smoke pump.
Wir machen dieses Jahr praktisch keine Winterpause und somit gibt es nun ein paar Flüge ohne Absteller.
Ich hab zwar noch kein Feintuning gemacht, kalte Finger nerven, aber Du kannst gern mal in meiner Cloud die Regelung ansehen.
Die NEO meckert zwar im Log gelegentlich "untere Regelgrenze" aber das soll vorerst mal so bleiben. Ich werd' sicher zum Sommer auch mal testen, was passiert, wenn ich Luft nach unten lasse aber für den Moment muss ich erst mehr Vertrauen in den Heli aufbauen. :-)
Was den anderen Thread mit den Schaltern (LS/Rettung) angeht, auch dazu muss ich mal 'ne ruhige Stunde haben, um das auseinander zu klamüsern. Wenn ich zu Hause den Heli vom Regal hole, ist sofort mein 2 1/2 jähriger dabei und muss überall mit seinen kleinen Schraubenziehern dran... da geht sowas nicht :-)
Fazit bis heute - keine Absteller. Die Pumpe war schuld. Allerdings läuft die alte Pumpe an einem brushed Regler weiter und wird als Smokepumpe dienen.