← VBar NEO/EVO VLink

Vbar Evo with OMP Hobby M4 Max and the 85A controller - Help translated

VBar › VBar NEO/EVO VLink · Started by Tgilf on 12 June 2026 17:2412.06.2026 17:24
Tgilf 12 June 2026 17:2412.06.2026 17:24
Hi everyone. I removed the MSH Brain and set everything up with the Vbar Evo at my leisure. So far, so good.
When I connect the motor cables and insert the battery, the motor beeps continuously and I get an error message: "Controller error code set, check log." The log shows: "OMP ESC power-on test / throttle zero test." What am I doing wrong? So far, I've been using the OMP ESC's internal governor...
I set the gas to 40 for bank 1, 50 for bank 2, and 60 for bank 3...

Thank you for your help!

Tom
machine-translated from German · Show original
RV 12 June 2026 17:5012.06.2026 17:50
Hi Tom,

The controller should normally automatically detect and adjust itself using Mikado telemetry.

How was it put into operation?
After the controller was connected via Tele, was the corresponding HW Mode selected and sent over in the model setup?
Is the controller also connected to the ESC?
Do you perhaps have the motor switch on a push-button switch instead of a 3-way switch?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Tgilf 12 June 2026 18:0212.06.2026 18:02
Thanks Rainer,

In the model setup, I selected the external ESC governor. The ESC is connected to the Vbar Evo's ESC connector (black wire at the bottom, white wire at the top). I've connected the telemetry cable to the front connector on the side. It's transmitting the values, but it's beeping constantly. Should I try switching from StorGovernor to the Vstabi governor using the OMP Bluetooth module?
I've set the motor switch to switch 5 and the safety switch to switch 6. I've also activated bank 4, which is then autorotation in the middle position of switch 5...

Many thanks!!
machine-translated from German · Show original
RV 12 June 2026 19:1512.06.2026 19:15
Okay - that looks good.

Was an output frequency also set for the controller in the setup? If so, which one?

Could you connect a servo to the ESC (then connect the controller to, for example, AUX3) and see if it moves when the motor switch is turned on?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Tgilf 12 June 2026 21:0412.06.2026 21:04
I had selected 72Hz / 1500 / 1520µs and then increased it to 333 Hz...


I've made progress. If I change the endpoint setting in the menu controller output setting from 100 to 115 for the "Off" endpoint, then everything initializes and I can start the motor.

With my previous transmitter (Spektrum NX 10), I had to start at 100% throttle to calibrate the endpoints with a linear throttle curve in order to calibrate the controller to the throttle range. Do I have to repeat this process? If so, how do I do it with Vbar?

At 40 throttle, it's running at almost 1800 rpm, if the reading is correct – with my Spektrum and the Brain, it was around 1400-1500 rpm... I think something's still wrong here...
machine-translated from German · Show original
RV 12 June 2026 23:4612.06.2026 23:46
So:

As already mentioned, the HW ESC MUST automatically set OUR throttle paths when it detects the Mikado Tele. Therefore, this fiddling around is unnecessary.

If it doesn't, it could be because it either doesn't recognize Mikado (but then there would be no telemetry) or hasn't had its mode reset.

Now we're going to do the following: we're switching to VGov. Please ONLY do this:

- Leaves down (all)
- Ensure that the RPM connection of the controller is also connected to the RPM input of the stabilizer.
- Gas passages restored to original
- Safety switch in the "On" position - don't let it spit in us.
- Motor switch in "Off"
- In VBar Setup - Change Setup - Scroll all the way down the display
- Reset controller mode to VBar speed control (Is the button with the HW icon there then?)
- Check gear ratio and number of poles (should match)
- Unplug the model, plug it in 10 seconds later
- In the flight panel (2nd page of the main screen, scroll down), set a sensible RPM as the target for each bank.
- Start the engine and see if it works now (It's possible that the lowest target RPM could now be slightly exceeded due to the lack of load)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Tgilf 13 June 2026 10:3513.06.2026 10:35
Good morning
I followed those instructions exactly. It's an OMP controller, by the way, and the symbol is correct.

After switching to Vbar governor, the engine started immediately at approximately 400 RPM, despite the engine being off and safety being activated... after restarting, the same error message appeared again with "ESC start throttle 0 test"...
machine-translated from German · Show original
RV 13 June 2026 10:4113.06.2026 10:41
Aha... strange. Looks like OMP must have been asleep when they read our specs. But somehow I'm not too surprised ;-(

But then, just adjust the gas lines as an exception.

What happens when you set an RPM and turn it on – does it still reach that speed?
Since we are unloaded and have no leaves, please use a high RPM, otherwise it might not regulate itself.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 13.06.2026 10:42 von RV.
machine-translated from German · Show original
Tgilf 13 June 2026 11:0413.06.2026 11:04
I disconnected the engine again and restarted it. Now it worked with the Vbar Governor. A few questions about that, Rainer:

1. It slowly ramps up to 1400 rpm, and then when I apply full or negative pitch, the speed increases to 1700 rpm? (without blades on the table) Is that normal?

2. When I assign AR to bank 4 in the bank management settings, it sets the throttle to 17%, which corresponds to approximately 600 rpm – why? I thought there shouldn't be any throttle applied during AR? Regardless of the fact that I haven't mastered the maneuver :-)

3. Do you think I can fly it like this? Or should I switch back to the OMP ESC Gov Store?

Thank you so much for the always prompt help!! Really great!
machine-translated from German · Show original
RV 13 June 2026 17:1713.06.2026 17:17
1 - normal, that's the gas curve in the background. More info about our Gov:

https://www.vstabi.info/de/node/2033

2 - equally okay, revs up faster if the controller is still in commutation

Everything fits!

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Tgilf 13 June 2026 18:2013.06.2026 18:20
Thank you!!!
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless