← VBar NEO/EVO VLink

Rear end oscillation at high rpm translated

VBar › VBar NEO/EVO VLink · Started by Tgilf on 22 June 2026 06:5022.06.2026 06:50
Tgilf 22 June 2026 06:5022.06.2026 06:50
Hello everyone - I'd like to ask for some advice again.

Yesterday, when I increased the engine speed to 2600rpm (Bank 3) on my OMP M4 Max with the Vbar Evo, the following happened:
After full pitch and leveling, the tail started to oscillate rapidly and frighteningly. I reduced the engine speed and frantically pressed the emergency brake. Then it was stable again. Safe landing.
Is this a mechanical issue or a setting? I've never experienced this behavior at lower RPMs.

Thank you all and best regards

Tom
machine-translated from German · Show original
RV 22 June 2026 07:2022.06.2026 07:20
Hmmm... if someone used a rescue service, it must have been more than just "shuttle-shuttle", right?

Which tail servo is installed, and what are its control frequencies and sensitivities?
Could the tail servo have overheated?
And which version is installed on the stabilizer? Vx.y?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Tgilf 22 June 2026 08:5822.06.2026 08:58
Yes. It was more than just commuting; it looked pretty wild...
The tail servo is the OMP DS3515T with 560Hz, I think I selected it as 500Hz in the configuration because 560Hz wasn't available....

I find that the rear servo always gets very warm.

The version on the stabilization software is from before the last update, I think it's 8.2 - but I'll double-check later if that helps you.

Thank you!!
machine-translated from German · Show original
Tgilf 22 June 2026 16:5022.06.2026 16:50
I checked again. I've set it to 500Hz and 760µs.
The tail servo gets warm even when stationary. The swashplate servos don't…
V8.2 is installed.

Can you deduce anything from that, Rainer?
One more thing


I'm using the Vstabi governor. I read that with direct drive, you should set the sensitivity of the speed controller to 10. Is that correct?



Edited once. Last edited on 22.06.2026 at 17:06 by Tgilf.
machine-translated from German · Show original
RV 22 June 2026 17:4322.06.2026 17:43
Yeah - 10 Gain is okay for now.

Regarding the servo – servos tend to become slightly less powerful (protective mechanism) when they get hot. This overheating is sometimes exacerbated by the fact that even the smallest vibrations are picked up by the tail sensor and then transmitted to the servo at high speed.

Try 333 Hz for comparison, maybe that will be enough.

If that is sufficient - and the vibration analysis is "clean" - the above would be correct.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Tgilf 22 June 2026 17:5422.06.2026 17:54
Thanks! I'll test it.
machine-translated from German · Show original
Max8200 22 June 2026 17:5522.06.2026 17:55
Unfortunately, I can't help you directly with that, but my M4 had terrible problems with the rear end (there's a thread about troubleshooting here and "next door").
After I replaced the tail servo twice, the helicopter was set up by Daniel Wiedenmann, and then everything was fine for a while. Since then, I've flown about 50 battery packs, and the tail oscillation in hover flight is back, even though NOTHING has been changed.
The rear end also no longer locks into place as cleanly as after the adjustment.
My tail servo doesn't get hot at all. Not even warm. However, the T/S servos get quite warm after running through three batteries at once.


I'll tackle that next week, and if I make any progress, I'll let you know here :-)

Best regards,
Lars
machine-translated from German · Show original
Tgilf 22 June 2026 21:0622.06.2026 21:06
Thank you!!
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless