← VBar NEO/EVO VLink

Touch screen with VBar control receiver on the old black stabilizer translated

VBar › VBar NEO/EVO VLink · Started by TimoH. on 7 October 2026 16:1307.10.2026 16:13
TimoH. 7 October 2026 16:1307.10.2026 16:13
I got myself a Touch with an Evo. It's a great piece of kit.
I have an old helicopter where converting it isn't worth the effort. So I bought this VBar RX Sat. I updated my old black VBar from software version 5.3.4 to 6.0.7.
RX connected and bound. So far, so good. The Touch also displays the stabilizer menu, the serial number, and the firmware version. But none of my servos are moving. When I turn it on, the Touch says the calibration is complete, but with an exclamation mark! There's no movement on the swashplate either. I've gone through the menu and adjusted all the parameters, but without success.

When I connect the black version of the Stabili (with satellite receiver) to the PC via USB and try to open it with the Neo PC version 6.4, I can't access it. Is this version even compatible?

It would be great if someone could help me get my old stabilizer working again.

Regards, Timo

The swashplate has a BLS 451 servo, and the tail has a BLS 254 servo. The BLS 254 servo on the tail exhibits a twitching behavior when the helicopter is in program mode.
50% of the set values for main rotor, tail rotor, etc. are also incorrect.

For example, Bank 1 is -50, Bank 2 is 30, and Bank 3 is again -50.



Edited 5 times. Last edited on 07/10/2026 at 17:24 by TimoH.
machine-translated from German · Show original
RV 7 October 2026 19:2407.10.2026 19:24
You need to create a new setup with the VBC.

PC no longer works with Altstabi and V6.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
TimoH. 7 October 2026 19:3707.10.2026 19:37
Thank you, that was the problem.

Timo
machine-translated from German · Show original
TimoH. 7 October 2026 19:5007.10.2026 19:50
Now I have the problem that after starting and initializing, the swashplate servos no longer move. The touchscreen says calibration is complete.
That's not normal, is it?

Timo.
machine-translated from German · Show original
RV 7 October 2026 20:3807.10.2026 20:38
Timo,

Support for the older Stabiliser models has actually expired.

If the corrections work, that should be okay. Pitch sugar may depend on the servos used and the initial position of the pitch lever, but I can't check it anymore since I don't have the equipment.

If it's in the VBC, then it should be good.

Generally speaking about old Stabis:


************************************************************
All these older devices are no longer supported. Therefore, please use the self-service option on our website (archive section) and the videos provided there.

https://www.vstabi.info/de/node/2504

As a final piece of support from us, here are a few more tips; no further support will be provided.

So, if you want to use an older VBar (plastic sensor or VBar Mini, NOT an aluminum sensor or NEO) with non-VBC radios, follow these steps if you haven't already:

First: Add the device to your account:
- if not already done - obtain a Mikado ID (EU shop for login at vstabi.info)
- Download and install the PC software version 5.3. Ensure a connection to VBar is established.
- if not registered - register VBar (upload a screenshot, read the registration instructions completely)
- You will probably have to wait until it is transferred to your account (manual transfer takes a few days)

Second: Perform an update/upgrade if necessary.
- If the PC software reports that there is no suitable version when switching on.
- Perform an online update (see the procedure for sending the license key).
- If only V5 Express is activated, purchase V5 Pro and repeat the online update.
- Double-check the entire setup

No connection to VBar
- Check the driver installation as shown in the PC software setup video.
- Use the recovery procedure
- Then register and check the options to be loaded again.

Note: The recovery version is a non-flyable version. Afterwards, a V5 Express or Pro version for third-party transmitters must always be loaded. See the videos for instructions.

Generally
- Do not download any software from sources other than vstabi.info
- Consider these elements as unsupported.
- If you have a detailed and specific question about the setup, etc., please contact us in the forum (separate account).

Downloads and manuals
https://www.vstabi.info/de/node/1714

Video collection
https://uroehr.de/vtube/cat/old-v5-vbars-archive -
*****************************************************

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
TimoH. 7 October 2026 21:0707.10.2026 21:07
Thanks for the info.
It was still twitching yesterday with the old version. Since the message appears on the transmitter, it should be fine. Like you said. Everything else is working fine. Since I haven't changed anything hardware-wise, I'm not suspecting the servos.
Oh well

Timo
machine-translated from German · Show original
Dirtygeri 8 October 2026 11:5408.10.2026 11:54
Hi Timon!
Please don't be offended, this is just my honest opinion, since someone always wants to dust off their "old" stuff... including a very good friend of mine... Even if it's an "old" helicopter, why not buy a new one, or at least a used Neo... or better yet, an Evo... it's safer, better, faster, works flawlessly, has full telemetry, etc., etc., etc., and above all, it flies worlds better... You'll save yourself a lot of trouble...
Best regards, Geri
machine-translated from German · Show original
TimoH. 8 October 2026 14:5208.10.2026 14:52
Hello Geri.

That has nothing to do with dusting. I'm still using the old stabilizer in six helicopters and it does what it's supposed to. And yes, I now know the difference to the Evo, since I already own two.

Timo



Edited once. Last edited on 08/10/2026 at 14:53 by TimoH.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless