← VBar NEO/EVO VLink

Which 15mm Midi servos are compatible with VBar EVO? translated

VBar › VBar NEO/EVO VLink · Started by PMDirk on 10 October 2026 17:1310.10.2026 17:13
PMDirk 10 October 2026 17:1310.10.2026 17:13
I have a question for you.
I'm using a LOGO 480 mechanics system with VBar NEO and Savox SV 1261 MG HV servos on the swashplate in a scale helicopter with a head speed of 1500 rpm. The helicopter flies superbly without any bouncing or other issues.
I have now built another LOGO 480 mechanism, but this time with a modern VBar EVO.
Based on the aforementioned positive experience with the VBar NEO and Savox SV 1261 MG HV servos on the TS, I'm using the same Savox servos on my VBar EVO. The helicopter is (still) being used as a trainer with 500mm main rotor blades. Unfortunately, I can't eliminate the pitch oscillation after short pitch inputs, neither with V7 nor V8 servos and 1500 rpm at the rotor head.
I think the problem lies with the TS servos; I'd like to test a different set of TS servos. Which current HV midi servos would you recommend for the VBar EVO?

Thank you very much and best regards
Dirk
machine-translated from German · Show original
Max8200 10 October 2026 18:4110.10.2026 18:41
The KST X15-1809 servos work perfectly; if not, you can be sure it's not the servos' fault :-)

Best regards,
Lars
machine-translated from German · Show original
sme 11 October 2026 09:2111.10.2026 09:21
Hi Dirk,

Unfortunately, the Evo is difficult to adjust with older servos and away from high RPMs.
I've had this problem with several helicopters as well.
But it doesn't always have to be a servo replacement.


Depending on the model, the following helped me.
TDF: Sensitivity significantly increased to 230, then reduced back to 200 as recommended by Uli to remain within a safe range. Fine-tuning with stop support.

Kraken700: Direct drive percentage significantly reduced, followed by fine-tuning of steering behavior and stop support.

So it's possible without replacing the servo, but it involves a lot of adjustments and testing.

Best regards
Stefan
machine-translated from German · Show original
PMDirk 11 October 2026 14:4711.10.2026 14:47
Hello Lars and Stefan,
Thank you so much for your information.

@Stefan
I have already tried and tested many settings with the VBar EVO, but unfortunately I cannot get close to my "VBar NEO reference" described in the opening post.
Therefore, I would like to try other TS servos.

Regards, Dirk
machine-translated from German · Show original
Eddi E. aus G. 12 October 2026 09:2212.10.2026 09:22
Hi Dirk,

How do you approach it?

LOGO 480 Setup from the 'New Setup' card file?
Did you change anything else after that?

In my experience with support, I get the impression that the standard setups still work well.

However, if you then choose the [...] basic settings in V8, for example, things can go wrong because they may be too sensitive for 'more normal' servos (or simply not suitable for micro-helicopters like the 200 or Stratos, because the optimal value range is very narrow there...).

And at the TS, 144 Hz / 1,520 µs should be 'achieved', which is the same as with the NEO, which has 'always' been a good mathematical match for our speeds up to around 2,000 rpm.

If in doubt, please try the (standard setup) again, and then just experiment with maneuverability, steering behavior and sensitivity :-)

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
PMDirk 12 October 2026 20:2212.10.2026 20:22
Hi Eddi,
Thank you for your reply. That's certainly another approach, with a completely new standard setup under the V8. I'll test it again this weekend or soon.
Do you have any other recommendations/tips for current TS-Midi servos for the VBar EVO?

Regards, Dirk
machine-translated from German · Show original
Eddi E. aus G. 13 October 2026 09:1713.10.2026 09:17
Hi Dirk,

Not really, because... a standard setup with minor adjustments to sensitivity/control behavior has always worked for me.

And I don't understand it the other way around either... I recently got my hands on a cheap Chinese drone about 200 size, with the built-in flight control and bus receiver 'adequate' and with some adjustment of maneuverability and expo 'satisfactory'.
Then I screwed on the ESC from our 200-size helicopter and an EVO micro ESC, leaving the 200-size setup as it was, only adjusting the trim and pitch, setting it to 8° by eye, and... it flies like a 200-size, 'good'. With some adjustments to sensitivity and control behavior, it even gets a 'good to very good' rating for what it is.

I think there are a lot of self-inflicted problems circulating :-) minus the courage to try something, or the idea, hey, if it doesn't work like this, I'll start all over again and approach it from the bottom up.

There will always be exceptions, and optimization is always possible, but in my experience, the rule is that it simply works as it is.

I'm curious to see your results!

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless