Good morning,
I think it's because everything runs through free mixers (macro cells), directly from stick/switch (of the bound transmitter) -> (mixer) -> S.BUS output.
Functions other than the normal controls (sticks) are never taken over by the student, only the calculated stick inputs (original functions, FC pitch-roll-tail input), which, however, run into nothing in the configuration.
The trick would be to choose the calculated functions FC*** in the relevant macro cells instead of the raw stick inputs, pitch and roll***.
But then the problem arises that one could change the input signal via agility (such as dual rate) and expo, for example (or would have to adapt it to what the external flight control wants/needs).
However, this was not desired at the present (or then) time, or (strongly suspected) there is even an error in the preset – after all, the preliminary page in the model setup states that agility 65 Expo 0 should remain set, which in my opinion they are not, since the stick is set to full travel as an input, where agility and expo have no effect on the flight parameters (shouldn't/shouldn't?).
If I change this for MC11/E1CH1 Roll to FC Roll, ..CH2 Nick to FC Nick, ..CH4 Tail to FC Tail, I can switch the three functions with L/S.
Interestingly (see above), max. Nick then changes from +/- 100 to +/- 78 (65% maneuverability of the max. range of 120% including everything, the values mentioned on the introductory page, which also do not correspond to 65 if that is really desired).
While roll-pitch-tail a solvable equation would be, I wouldn't know where to get the native pitch function from, which doesn't exist with a pure receiver (without a hand-built swashplate mixer, which then also doesn't have the original function). There, the throttle stick has a single, unambiguous function: throttle.
Thinking further: 'One could' of course use FC ESC as the input for the pitch curves, thus essentially controlling the throttle function (which can be passed on to the receiver), but this means that the motor switch then has idle throttle as a fixed pitch position and motor off as full negative pitch.
That would be at least... unusual :-) and in my opinion not really practical or dangerous in practice.
Perhaps Rainer will think of something else that I'm overlooking.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
ich denke, es liegt daran, dass da alles durch freie Mischer (Makrozellen) läuft, direkt Stick/Schalter (des gebundenen Senders) -> (Mischer) -> S.BUS-Ausgang.
Funktionen abseits der normalen Steuerung (Knüppel) werden nie vom Schüler übernommen, nur die berechneten Stick-Inputs (Originalfunktionen, Eingang FC Nick-Roll-Heck), die laufen in der Konfiguration aber in's Leere.
Der Trick wäre, statt der rohen Knüppel, Eingang Nick-Roll*** die berechneten Funktionen FC*** in den betreffenden Makrozellen zu wählen.
Dann tut sich aber das Problem auf, dass man über Wendigkeit (wie Dual Rate) und Expo bspw. das Eingangssignal verändern könnte (bzw. an das anpassen müsste, was die fremde Flight-Control will/braucht).
Das ist aber zum jetzigen (oder damaligen) Zeitpunkt nicht gewünscht (gewesen), oder es liegt (starke Vermutung) sogar ein Fehler im Preset vor – immerhin wird ja in der Vorschaltseite im Modellsetup geschrieben, dass Wendigkeit 65 Expo 0 gesetzt bleiben sollen, was sie aber mMn nicht sind, da der Knüppel mit vollem Weg als Eingang gesetzt ist, wo sich Wendigkeit und Expo in den Flugparametern gar nicht auswirken (sollen-dürfen?).
Ändere ich das für MC11/E1CH1 Roll zu FC Roll, ..CH2 Nick zu FC Nick, ..CH4 Heck zu FC Heck, kann ich die drei Funktionen mit L/S umschalten.
Interessant (vgl. weiter oben), max. Nick verändert sich dann von +/– 100 auf +/– 78 (65 % Wendigkeit vom max. Weg von 120 % inkl. allem, den in der Vorschaltseite genannten Werten, die aber auch nicht 65 entsprechen, wenn das wirklich gewollt ist).
Während Roll-Nick-Heck also eine lösbare Gleichung wäre, wüsste ich nicht, woher ich die native Pitch-Funktion herholen sollte, die's ja bei reinem Empfänger (ohne handgedengelten TS-Mischer, der dann aber eben auch nicht die Originalfunktion hat) nicht gibt. Dort hat der Gasknüppel ja eine ein-eindeutige Funktion, Gas.
Weiter gedacht: 'Man könnte' jetzt natürlich FC ESC als Eingang für die Pitchkurven verwenden, damit quasi die Gasfunktion (die ist beim Empfänger ja übergebbar), bedeutet aber, dass der Motorschalter dann Leerlaufgas als feste Pitch-Stellung hat und Motor Aus als voll Negativ-Pitch.
Wäre jetzt mindestens ... ungewohnt :-) und mMn in der Praxis nicht wirklich praktikabel bzw. gefährlich.
Vllt. fällt dem Rainer noch was ein, was ich übersehe.
Grüßle
Eddi
Born to fly ...
forced to work.