thomas1130
6 May 2026 15:0306.05.2026 15:03
Hi :-)
Now that I've managed to get my hands on two of the new RX (1) only SBus receivers, I'd like to replace the existing (stripped) RX-7 only in my M2V3 with the new small RX...
Quick question for clarification:
If I back up the old model setup and transfer it to the new receiver, should that work?
Does that mean all macrocells are transferred along with their settings?
Or does it work differently than with Neo / Evo?
Thanks!
Best regards,
Thomas
Hi :-)
Nachdem ich jetzt 2 der neuen RX (1) only SBus Empfänger ergattern konnte, möchte ich in meinem M2V3 den bisherigen (gestrippten) RX-7 only durch den neuen kleinen RX ersetzen...
Kurze Verständnisfrage:
Wenn ich das alte ModellSetup sichere - und auf den neuen Empfänger übertrage sollte das funktionieren?
Dh alle Macrozellen werden übertragen samt Einstellungen werden damit übertragen?
Oder läuft das anders wie bei Neo / Evo?
THX!
LG,
Thomas
Eddi E. aus G.
6 May 2026 15:4106.05.2026 15:41
Good morning,
No, everything works the same way every time; the bus receiver is a VBasic like RX-Only or just VBasic.
. As is typical with VBar, perhaps create a new setup first so that everything is properly configured (remember, on a brand new NEO or EVO, the servo output is also locked until you...)
Then load the saved MC, and load the saved setup, and 'watch out', turn off the reeds/prop first in case something starts up.
Or from the very beginning,
. infect
bind
off-on
New setup, OMP or OFS3 depending on the helicopter
Pre-flight check
. go flying
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
neee, funktioniert alles und immer und gleich, der Bus-Empfänger ist ein VBasic wir RX-Only oder eben VBasic auch.
. VStabi-typisch, vielleicht erst mal ein neues Setup erzeugen, damit überhaupt alles grundbesamt wird (zur Erinnerung, bei einer schachtelneuen NEO oder EVO ist die Servo-Ausgabe ja auch gesperrt, bis man ...)
. dann gespeicherte MC laden, und gespeichertes Setup laden, und 'ufbasse', Blätter/Prop erst mal ab falls was anläuft.
Oder von ganzvonvorn,
. anstecken
. binden
. aus-an
. Neues Setup, OMP oder OFS3 je-nach Heli
. Vorflugkontrolle
. fliegen gehen
Grüßle
Eddi
Born to fly ...
forced to work.
thomas1130
6 May 2026 15:5506.05.2026 15:55
Thanks Eddi,
I wasn't entirely clear on the "basic insemination" thing - I thought that only applied to EVO / NEO - and not just RX-only...
I just have to wait until the storm here in Vienna subsides, otherwise the dwarfs won't happen ;-)
THX!!
Best regards,
Thomas
Edited once. Last edited on 06/05/2026 at 15:55 by thomas1130.
Danke Eddi,
das mit der "Grundbesamung" war mir nicht ganz klar - dachte das betrifft nur EVO / NEO - und nicht reine RX-only..
Muss nur warten, bis sich der Sturm hier in Wien wieder legt, sonst wird das nix mit den Zwergen ;-)
THX!!
LG,
Thomas
1 mal bearbeitet. Zuletzt am 06.05.2026 15:55 von thomas1130.
Eddi E. aus G.
7 May 2026 08:5607.05.2026 08:56
Good morning,
I'd have to test it again myself, I don't have a virgin one here right now.
But that's what the average person does anyway, a new setup.
Only the specialists want to take shortcuts :-) (and sometimes even make it worse by carrying over a setup that has been dragged along for years from the version before the one before the one before, or by loading a foreign setup instead of creating a new one, even improving something in the process, and being amazed...).
It's not that complicated for us either: keep an eye on the versions, scripts, conduct test flights, research the results, readjust, set up telemetry, ... :-)
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
ich müsste es auch nochmal testen, hab grad keinen jungfräulichen mehr hier.
Aber das ist ja das, was der Normalo sowieso macht, ein neues Setup.
Nur die Spezialos wollen abkürzen :-) (und machen's dabei sogar manchmal schlechter, indem sie ein schlimmstenfalls über Jahre mitgezogenes Setup der vor-vor-Vorversion mitnehmen, oder ein Fremdsetup laden, statt mal ein neues zu machen, dabei sogar noch was zu verbessern, und zu staunen ...).
Is bei uns ja auch nicht soo kompliziert, Versionen beachten, Skripte, Messflüge machen, Ergebnisse recherchieren, nachjustieren, Telemetrie einrichten, ... :-)
Grüßle
Eddi
Born to fly ...
forced to work.
thomas1130
7 May 2026 12:5707.05.2026 12:57
Hmm - I've tried it now - but I'm not entirely sure...
I know how it works with "normal helicopters" and EVO or NEO - no problem, I (almost) always do a new setup anyway.
But here - with SBus only plus macrocells I'm unsure:
When you back up/load the setup, are the macro cells also backed up or loaded?
Is/must the macrocell be backed up or reloaded "separately"?
Background - the "flight characteristics" and rotational speeds are hidden in (painstakingly determined) values in the macro cells - therefore, a "new setup" simply doesn't help me - I would then be back to square one..
Please clarify - THANK YOU!
Best regards,
Thomas
EDIT:
Additional "problem":
The radio went directly into setup after connecting the RXmini - no registration prompt.
Therefore, the recipient does not appear under "my devices" in the cloud!?
How can I restart this?
Edited once. Last edited on 07/05/2026 at 13:01 by thomas1130.
Hmm - habe es jetzt ausprobiert - aber so ganz sicher bin ich mir nicht..
Ich weiß wie das mit "normalen Helis" und EVO oder NEO geht - kein Problem da mach ich sowieso (fast) immer ein neues Setup..
Aber hier - bei SBus only plus Makrozellen bin ich unsicher:
Werden beim Setup sichern/laden AUCH die Makrozellen gesichert bzw geladen??
Kann/muss man die Makrozelle "extra" sichern bzw wieder laden??
Hintergrund - die "Flugeigenschaften" und Drehzahlen verstecken sich ja in (mühsam erflogenen) Werten in den Makrozellen - von daher nützt mir einfach ein "neues Setup" nicht - dann wäre ich ja wieder bei Stunde null..
Bitte um "Aufklärung" - DANKE!
LG,
Thomas
EDIT:
Zusätzliches "Problem":
Die Funke spran nach Anschluss des RXmini direkt in Setup - keine Abfrage der Registrierung..
Daher taucht der Empfänger auch nicht bei "meinen Geräten" in der Cloud auf!?
Wie kann ich denn das neu initiieren?
1 mal bearbeitet. Zuletzt am 07.05.2026 13:01 von thomas1130.
Dirtygeri
7 May 2026 13:0707.05.2026 13:07
Hi Thomas!
You can't see the forest for the trees, can you?
Connect/turn on the RX7 - Save the setup under name XY, then save the macro cell setup under name XZ and turn it off.
Then connect the RX S-Bus to power/switch it on - bind it to the transmitter - create a new setup... switch it off when finished.
Then connect/switch on the RX S-Bus - load the RX7 setup (names XY, macrocells) - load the RX7 setup (names XZ)... switch off when finished
Then install/connect the RX S-Bus to the new model, connect it to power (it's best to do this without blades to avoid any accidents) - switch it on and check all functions; if everything is OK, attach the blades and fly...
Just like always... 8-)
Best regards, Geri
Hi Thomas!
Du siehst den Wald vor lauter Bäumen nicht, oder?
RX7 mit Strom verbinden / einschalten - Setup unter NamenXY speichern, dann Makrozellen Setup unter Namen XZ speichern und ausschalten
Dann RX S-Bus mit Strom verbinden / einschalten - mit Sender binden - neues Setup anlegen ... wenn fertig ausschalten
Dann RX S-Bus mit Strom verbinden / einschalten - Setup vom RX7 laden = NamenXY, Makrozellen Setup vom RX7 laden = Namen XZ ... wenn fertig ausschalten
Dann RX S-Bus in das neue Modell einbauen / anstecken, mit Strom verbinden (ohne Blätter von Vorteil, damit nichts passiert) - einschalten und alle Funktionen überprüfen, wenn alles ok, Blätter drauf und fliegen ...
So wie immer halt ... 8-)
Beste Grüße, Geri
Eddi E. aus G.
7 May 2026 13:2007.05.2026 13:20
Hi,
Quote: me
Then load the saved MC and load the saved setup.
This implies that you have to save and load both :-)
The issue of 'laboriously acquired through flying' is another one of those: OMPHOBBY wants further settings to be made only in the helicopter.
Many roads lead to Rome, though.
Quote: thomas1130
The radio went directly into setup after connecting the RXmini - no registration prompt.
This always happens when a new device/one without a suitable setup is detected.
Normally, you would simply do it and finish, or finish and update via the VBar NEO/EVO Updater app and the QR code there.
However, it doesn't come up with the 'short' ones; either something else will come, or one cannot (and must not...) register them.
But this does not affect the functionality.
Grüßle
Eddi
Born to fly ...
forced to work.
Hi,
Quote:me
. dann gespeicherte MC laden, und gespeichertes Setup laden
Impliziert, dass man beides speichern und laden muss :-)
Das Thema mit 'mühsam erflogen' ist auch so eines: OMPHOBBY wünscht sich ja, dass man weitere Einstellungen nur noch im Heli macht.
Viele Wege nach Rom führen, trotzdem.
Quote:thomas1130
Die Funke spran nach Anschluss des RXmini direkt in Setup - keine Abfrage der Registrierung.
Das passiert immer, wenn ein neues Gerät/eins ohne geeignetes Setup erkannt wird.
Normal würde man einfach machen und beenden, oder beenden, und über die VStabi NEO/EVO Updater App und den QR-Code dort updaten.
Der kommt aber bei den 'kurzen' nicht hoch, entweder kommt da noch was, oder man kann (und muss ...) sie nicht registrieren.
Tut der Funktion aber keinen Abbruch.
Grüßle
Eddi
Born to fly ...
forced to work.
thomas1130
7 May 2026 13:2107.05.2026 13:21
Thanks Geri - that's exactly how I did it "intuitively" - first setup - then macro... - and it worked as expected... :-)
Eddi didn't explicitly "mention" it - or rather, I "overlooked" it - so I asked again here 8-)
The problem with registration remains:
I have the flights in the cloud - but the recipient does NOT appear under "my devices".
LG
Thomas
PS: He is "cute"... :-)
P.S.: This overlapped with Eddie's answer.
Edited 4 times. Last edited on 07/05/2026 at 13:36 by thomas1130.
Danke Geri - genau so habe ich es eh "aus dem Bauch" gemacht - zuerst Setup - dann Makro.. - hat auch wie erwartet funktioniert.. :-)
Bloß hat Eddi nicht so explizit "erwähnt" - bzw ich "überlesen" - daher habe ich hier nochmals nachgefragt 8-)
Bleibt das Problem mit der Registrierung:
Ich hab zwar die Flüge in der Cloud - aber der Empfänger taucht NICHT unter "meine Geräte" auf..
LG
Thomas
PS: "Süß" ist er schon... :-)
PPS: hat sich mit Eddis Antwort überschnitten
4 mal bearbeitet. Zuletzt am 07.05.2026 13:36 von thomas1130.
thomas1130
7 May 2026 13:4007.05.2026 13:40
Quote: Eddi
However, it doesn't come up with the 'short' ones; either something else will come, or one cannot (and must not...) register them.
But this does not affect the functionality.
Just checked - the old RX7 only doesn't appear in my device list either - I hadn't even noticed that before - seems to be "normal".
I do wonder why – and how one would create a service request in such a case – but as you rightly say – it doesn't affect the functionality :-)
Best regards,
Thomas
Quote:Eddi
Der kommt aber bei den 'kurzen' nicht hoch, entweder kommt da noch was, oder man kann (und muss ...) sie nicht registrieren.
Tut der Funktion aber keinen Abbruch.
Gerade nachgesehen - der alte RX7 only taucht auch nicht auf in meiner Geräteliste - ist mir bis jetzt noch gar nicht aufgefallen - scheint "normal" zu sein
Frage mich zwar warum - und wie man im Fall der Fälle einen Servicefall anlegen würde - aber wie du richtig sagst - tut der Funktion ja keinen Abbruch :-)
LG,
Thomas
Dirtygeri
7 May 2026 13:4707.05.2026 13:47
I do have the flights in the cloud - but the
The receiver does NOT appear under "my devices".
> on..
I don't have an RX SBus receiver (yet), but normally on the VBAR Updater (where you do the update on the Vbar Neos / Evos 8-) ) - QR code appears and then, as always, scan, etc., right?
Geri
> Ich hab zwar die Flüge in der Cloud - aber der
> Empfänger taucht NICHT unter "meine Geräte"
> auf..
Habe (noch) keinen RX SBus Empfänger, aber normalerweise auf VBAR Updater (dort wo man bei den Vbar Neos´s / Evo´s das Update macht 8-) ) - QR Code kommt und dann wie immer, scannen usw. oder?
Geri
Eddi E. aus G.
7 May 2026 13:5007.05.2026 13:50
Hi,
I just connected a NEO mini (based on RX-Only 7), and the updater appeared; I could register it.
It has a normal NEO serial number (200...).
Regarding the service case, I would first note down the serial number somewhere (totally 90s, yes :-) ), and then you can also create a ticket without a serial number under vstabi.info/rma with 'Other parts', or for NEO/EVO, if the system 'eats' the serial number.
These are just backend issues, but we'll take a look at them sometime.
Grüßle
Eddi
Born to fly ...
forced to work.
Hi,
ich hab grad mal eine NEO mini (Basis von RX-Only 7) verbunden, da taucht der Updater auf, die könnte ich registrieren.
Hat 'ne normale NEO-Serienmummer (200...).
Zum Servicefall, ich würde mir zum einen die Seriennummer ggfs. irgendwo notieren (total 90-er, ja :-) ), und dann kann man ja auch unter vstabi.info/rma mit 'Andere Teile' ein Ticket ohne Seriennummer anlegen, oder für NEO/EVO, wenn das System die Seriennummer 'frisst'.
Sind nur Backend-Geschichten, die wir uns aber auch mal noch ansehen.
Grüßle
Eddi
Born to fly ...
forced to work.
thomas1130
7 May 2026 16:4907.05.2026 16:49
The updater isn't showing up for me – which I'm wondering about, how am I supposed to update the firmware if there ever is an update!?
But it flies perfectly fine - so that's not the problem.
And to everyone who is silently reading along here:
Definitely remove the rotor blades – the rotors will start spinning during setup anyway...
Best regards,
Thomas
Edited once. Last edited on 07/05/2026 at 16:49 by thomas1130.
Bei mir taucht der Updater nicht auf - was mich auch wundert, wie ich denn die FW updaten sollte, so es eines Tages ein Update gibt!?
Aber fliegt tut er einwandfrei - also das ist nicht das Problem.
Und an alle die hier still mitlesen:
Rotorblätter UNBEDINGT abmachen - bei Setup laufen die Rotoren jedenfalls an...
LG,
Thomas
1 mal bearbeitet. Zuletzt am 07.05.2026 16:49 von thomas1130.
RV
7 May 2026 22:0307.05.2026 22:03
- The devices cannot be registered by the customer.
- If necessary, we will provide an app for a possible update.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
- Die Geräte sind nicht durch den Kunden registrierbar
- Für ein mögliches Update wird von uns dann bei Bedarf eine App dazu bereitgestellt
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.