← VBar Control Touch / EVO

Learning the Benedine sound module translated

VBar Control › VBar Control Touch / EVO · Started by UweW on 1 February 2026 14:5201.02.2026 14:52
UweW 1 February 2026 14:5201.02.2026 14:52
Hello, I've installed a Benedini sound module with the original sound in my Roban AS350 helicopter. Please, no discussion about the pros and cons of turbine sounds in electric scalers :-) .
According to the description for learning the sound, the TBS Mini V2 module from Thomas B. is programmed to the operating mode "direct sound selection".
The module is supposed to be connected via the throttle channel and then calibrated using the throttle stick. But since I'm flying with a linear throttle input, that doesn't work.
My idea is to send the pitch signal to the sound module, not the throttle, since the throttle doesn't change. I'm using an EVO as my VBar.
I've attached the programming description, perhaps for better understanding.
Can someone give me a hand or do you have another suggestion?

Regards, Uwe

machine-translated from German · Show original
RV 1 February 2026 15:1401.02.2026 15:14
Pitch to an output, e.g. AUX2:

Macrocell channel, input collective (pitch). Done.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
UweW 3 February 2026 17:4403.02.2026 17:44
Hello Rainer,

Thanks for the info! It's simple, you just have to know it!
But I have another question, don't laugh.
I want to activate the sound module using 3-way switch No. 2. I have programmed AUX3 macro cell channel, input Sw2.
Unfortunately, no matter which position the switch is in (-100, 0, +100), the sound module starts working immediately when powered on! If I unplug the cable from AUX3, nothing happens! What do I need to adjust to make the switch work for this option?

Thanks!
machine-translated from German · Show original
RV 3 February 2026 18:4803.02.2026 18:48
The MC input is not SW2 - but Option 2.

You need to check in the switch settings which option (1, 2, 3) is assigned to the physical SW2 - that will be the input.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless