← XL Power Support

Stratos 200 - Headspeed translated

OEM models › XL Power Support · Started by thomas1130 on 25 June 2026 16:5725.06.2026 16:57
thomas1130 25 June 2026 16:5725.06.2026 16:57
Hi everyone,

I have a small "headspeed problem" with my Stratos:

The settings in the VBC EVO+ would be approximately 3800 / 4500 / 5200.

However, it feels quite (too?) "tame" for a 4s battery - and the log also shows headspeeds significantly below my values - in bank 3, for example, only 4390!?

Everything up to date - hardware controller update done - EVO also updated - and a new setup done again with the Stratos-200 preset?

Where is the mistake?

Thanks!

Best regards,
Thomas



Edited 2 time(s). Last edit at 06/25/2026 05:01PM by thomas1130.

machine-translated from German · Show original
RV 25 June 2026 17:3925.06.2026 17:39
RPM range in VGov incorrectly set (max 4800) - check the transmission...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




Edited 1 time(s). Last edit at 06/25/2026 05:40PM by RV.
machine-translated from German · Show original
thomas1130 25 June 2026 17:5125.06.2026 17:51
Thanks Rainer - I just applied the preset... - I'll check the value right away!

LG
machine-translated from German · Show original
RV 25 June 2026 17:5325.06.2026 17:53
And don't forget to readjust the RPMs afterwards.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
thomas1130 25 June 2026 18:0325.06.2026 18:03
RPMs? :-)

RPM -> :-)

RPMS -> ?



Edited 1 time(s). Last edit at 06/25/2026 06:22PM by thomas1130.
machine-translated from German · Show original
RV 25 June 2026 18:2225.06.2026 18:22
Quote: 3800 / 4500 / 5200


regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
thomas1130 25 June 2026 18:2325.06.2026 18:23
:-)

Thanks :-)

Greetings from hot Vienna :-)
machine-translated from German · Show original
thomas1130 25 June 2026 20:2025.06.2026 20:20
RV Wrote:
-------------------------------------------------------
> RPM range in VGov incorrectly set (max 4800) -
> Check the gearbox...


Hmm... but if I set the maximum to 4800, then the maximum selectable speed is also 4800!?

Shouldn't such a small engine be able to turn 5200 rpm?

14400 is probably too much - what about 9600??

And one more thing - 12 pole pairs - is that correct?

LG
Thomas



Edited 1 time(s). Last edit at 06/25/2026 08:20PM by thomas1130.
machine-translated from German · Show original
RV 25 June 2026 20:2925.06.2026 20:29
Yep - that's what I meant. Set it to 9600 and then you need to adjust the 3 RPM. Leave the rest as is.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Eddi E. aus G. 26 June 2026 09:4526.06.2026 09:45
Good morning,

I don't have one, but where is the (thinking) error?

The preset contains 14,400, and also 3,780-4,500-5,220, which should work according to my understanding, not be clipped?

Otherwise ... :-)

Acronym Definition
RPMS Rapid Prototyping Mission Simulator
RPMS Raymore Peculiar Middle School
RPMS Regional Pest Management Strategy
RPMS Remote Power Management System
RPMS Rep Profit Management System
RPMS Resource and Patient Management System
RPMS Rosa Parks Middle School
RPMS Rarely Purchased Management System

Rock-Paper-(M?)-Scissors ^^

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
thomas1130 26 June 2026 09:5826.06.2026 09:58
Eddi E. from G. wrote:
-------------------------------------------------------
> Hi,
>
> I don't have one, but where is the (thinking) error?
>
The preset contains 14,400, and that's it.
> 3,780-4,500-5,220, according to my understanding
> But they still work, not cut off?
>

Yes, exactly - that's how it is in the preset on the VBC - unfortunately, in reality, the thing spins noticeably less - across all banks...
This is also evident from the extremely low PWM openings of 49% and so on – that it "could do more" – especially on 4s..

Tried it today with 9600 -> exactly the same result - the set RPM and the log RPM (which seems correct based on gut feeling) don't match...

I could of course just set it to 7000 if I want 5000 - but that's not exactly "nice" :-)

Let's see - maybe another idea will come up :-)

Best regards,
Thomas
machine-translated from German · Show original
Eddi E. aus G. 26 June 2026 10:3426.06.2026 10:34
Good morning,

Price questions...

What happens, what do you see, when you unplug the RPM cable (please also check the controller telemetry menu)?
Does the rotational speed change, and how – when you change the base gas?
If you switch the controller to position mode and/or enable pitch control in the setup, can you then fully control it?

Which firmware version is on the controller (this information isn't very helpful since I'm not familiar with it, but...), perhaps one thing was fixed in the last update (telemetry bug), and another was made worse? Would it work properly (or better) with a different/older version (if possible)?

So far you seem to be the only one experiencing this phenomenon, congratulations :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
RV 26 June 2026 17:1626.06.2026 17:16
I'll contact XL support... there he is already!

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




Edited 1 time(s). Last edit at 06/26/2026 10:26PM by RV.
machine-translated from German · Show original
Carl-Henning Siebert 26 June 2026 20:1726.06.2026 20:17
Hello Thomas,

Which Hobbywing software do you have installed on the controller?

greeting
Carl
machine-translated from German · Show original
thomas1130 26 June 2026 20:2026.06.2026 20:20
Hello Carl,

The new PL-04.1.07 has recently been released.

But I don't think that has anything to do with it - I had the same "problem" with the factory-delivered version...

But at least the rear end is noticeably better now - I'm quite happy with that... now I just need some serious revs 8-)

LG
Thomas
machine-translated from German · Show original
thomas1130 28 June 2026 07:5928.06.2026 07:59
Tried it again today with a specific goal in mind - and got some very "strange" results:

It does n't matter what headspeed I set - it always spins at the same RPM for each bank!?

Bank1 - approx. 3300 - Bank2 approx. 3700 - Bank3 approx. 4400

First I tried it with the values from the screenshot - result above..

Then, for the test, bank 3 was set to 7500 - but it still spins at 4400!??

That's really strange - as if the RPM were stored in the controller, and I was only specifying the banks from the transmitter??
Would that be possible?

LG
Thomas



Edited 1 time(s). Last edit at 06/28/2026 08:00AM by thomas1130.

machine-translated from German · Show original
RV 28 June 2026 09:5428.06.2026 09:54
Have you already checked if the RPM signal is arriving at the RPM pin of the stabilizer?

Try unplugging the TELEphone, letting it run, and checking if the RPM is displayed - and if it's correct.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




Edited 1 time(s). Last edit at 06/28/2026 09:54AM by RV.
machine-translated from German · Show original
thomas1130 28 June 2026 11:1028.06.2026 11:10
That was exactly it - Rainer, you're a genius - THX :-)

The mini-pin connector for the rpm signal was loose – and I didn't notice it because "RPMs were being displayed anyway" – but these were obviously only coming from the telemetry... :-)

rpm plug properly attached - and now the little guy is turning as he should :-)

Then I increased the BEC voltage from the preset 6.0V even further – to a cautious 7.4V – this was recommended to me elsewhere as an "improvement".

Thanks to everyone here.. :-)

Greetings from super-hot Vienna,
Thomas

PS: Additional question: What is the difference between 9600 and 14400 maximum RPM?
Does the stabilization system calculate more precisely internally – i.e., with higher digital resolution or something like that?



Edited 1 time(s). Last edit at 06/28/2026 12:28PM by thomas1130.
machine-translated from German · Show original
ulrich 29 June 2026 23:4029.06.2026 23:40
This is an internal prescaler. With the lower setting, it's slightly more accurate. However, this shouldn't make any real difference, apart from the larger maximum value.

So long... Uli
http://www.vstabi.de
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless