← XL Power Support

Dolphin during high-speed flight in bank 2 translated

OEM models › XL Power Support · Started by MGU on 26 July 2026 16:4626.07.2026 16:46
MGU 26 July 2026 16:4626.07.2026 16:46
Hello,

I've been flying the little helicopter for a while now (about 50 flights) and am slowly pushing its limits, not the helicopter's limits, of course. Bank 1 works perfectly; the helicopter hovers and flies flawlessly. However, in Bank 2, I've noticed that after a quick turn, the helicopter starts to oscillate like a dolphin in straight flight. It flies straight ahead and then begins to oscillate via pitch. This isn't just a vibration, but a distinct dolphin oscillation with a constant amplitude. If I slow down (via pitch control) or intervene with the pitch control, it recovers. I know the helicopter isn't designed for high-speed flight, but I seem to recall there's a parameter for this, or am I mistaken?
Especially when flying fast turns at low altitude, it's quite a challenge. :-)



Edited 1 time(s). Last edit at 07/26/2026 04:48PM by MGU.
machine-translated from German · Show original
Eddi E. aus G. 27 July 2026 09:1527.07.2026 09:15
Good morning,

The cause is something mechanical, or rather, mechanical limits or excessively large angles of attack that no longer allow the VBar enough travel on the swashplate to counteract the pitching up.
Question, setup?
And in particular, what pitch angles are set? It's also possible that the servos are reaching their limits, kP.

Please save the current setup to the transmitter, to the cloud (say where), and provide some information, especially about the maximum pitch that is set.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
MGU 27 July 2026 10:1727.07.2026 10:17
Hello,

I've installed the standard setup for the Stratos 200 and haven't changed anything. So I don't know what the maximum pitch is set to.
I just saved the current setup and it's in my cloud.
machine-translated from German · Show original
MGU 27 July 2026 10:2227.07.2026 10:22
Oh, the sender ID is 11001848.
machine-translated from German · Show original
MGU 27 July 2026 10:2527.07.2026 10:25
Would lowering the gain on the main rotor help in this case?
machine-translated from German · Show original
Eddi E. aus G. 27 July 2026 12:2927.07.2026 12:29
Good morning,

Can't you measure pitch somehow, with a pitch gauge, or using geometry? :-)

Or ask the moderator here, he helped with the setup ^^ what the result should be.

Adjusting the gain won't help; trying pitch balance would be a shot in the dark, or conversely, turning the pitch down by half a degree or a full degree.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
MGU 27 July 2026 12:5027.07.2026 12:50
I'll see if my pitch gauge fits the small leaves.
The pitch balance seems a bit high to me at 65, I'll adjust it and see if it changes anything.
machine-translated from German · Show original
MGU 27 July 2026 17:0627.07.2026 17:06
So, I measured the pitch and got a positive and negative pitch of 9.2. That's actually relatively reasonable and should provide enough leeway, right?
machine-translated from German · Show original
Eddi E. aus G. 28 July 2026 09:3228.07.2026 09:32
Good morning,

Yes, that would be no problem.

I have no idea about the setup, and I've never actually flown a helicopter like this (only handled an unassembled kit once), but a pitch balance of 65 seems high to me. The standard is 35 (up to about the usual 12° angle of attack; for larger angles of attack, you'd decrease the value, and for smaller ones (as is the case here), increase it). It's quite possible that this value is actually suitable for the helicopter; things are often different with smaller models, and if you see unusual values, you might only have a small window where it works optimally.

It might still be a good idea to start here.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
MGU 28 July 2026 10:1528.07.2026 10:15
I set the pitch to 12 degrees and will then set the pitch balance to 35 and test it.
machine-translated from German · Show original
MGU 28 July 2026 10:2628.07.2026 10:26
One more question, because I've been looking into the pitch in more detail.

When I set positive and negative pitch in the model setup, these values are written to the pitch curves of all banks, which I can then adjust for each bank. Are these values used for anything else, or are they "only" an aid for the setup? For your information, the cyclic 8-degree value was also incorrect; I had it set to 6.8.
machine-translated from German · Show original
Eddi E. aus G. 28 July 2026 14:0128.07.2026 14:01
Good morning,

You have to experiment to find absolute pitch angles.

The LOGO 200, for example, also has a seemingly small pitch range, which is perfectly OK for the rotational speeds and blade geometry, and is additionally shifted depending on the flight condition and attitude by the parameter of lightness.

In the (basic) setup, you set – correctly – the minimum and maximum values, thereby simultaneously feeding (all) the pitch curves.

If you now change the pitch curves, they will behave individually and also per bank from then on.

If you now change or adjust something in the setup – poof – everything is the same again, straight, with the same endpoints.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
MGU 28 July 2026 17:3528.07.2026 17:35
My question was more along the lines of: do the minimum and maximum values I set only affect the pitch curve, or are they also used elsewhere in the control loop?
Regarding the maximum and minimum settings, all my "big" ones are set to +/-12 degrees pitch, but I'll take a look at the small one. There must be a reason why it's parameterized with less pitch by default. Just to be safe, I'll copy bank 1 to bank 2 and set the pitch curve there to +/- 72, just in case it gets too hectic. :-)
machine-translated from German · Show original
MGU 28 July 2026 20:4128.07.2026 20:41
Sooooo

I've just gone through eight battery packs and no matter what I change, it starts oscillating. I even managed to do it once on the lower battery bank. Different RPM, higher or lower pitch balance – it just oscillates. I also tried setting the swashplate algorithm to 8.2, but no change. I'm going to try different blades now.
machine-translated from German · Show original
Eddi E. aus G. 29 July 2026 09:0129.07.2026 09:01
Good morning,

Pitch ...

Rule 1, the maxima in the setup apply if nothing else is changed.
Rule 2, the settings in the pitch curves (override the values in the setup, bank-dependent)
Rule 3: If you adjust the setup again, all curves will be straightened between the maxima; pitch curves will be deleted.

With the LOGO 200, we also have a relatively low pitch as standard, but can easily add around 1-2-3° more.

Dolphin ...

Possibly (no, sure, aerodynamics and physics always win ^^) there are simply limits where the whole 'construction' of mechanics, servos, blades, setup starts to become unstable.
Remedy: fire a µ slower ^^ or possibly increase the pitch balance even further, or possibly 'lower' the overall pitch a little more (be nice!).
Ultimately, it's the point where the control loop can no longer provide enough pitch to suppress the pitching up; the helicopter raises its nose slightly, slows down a bit, grips better again, nose down, speeds up, ooomph, nose up, aaah, nose down... oaoa... up and down.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
MGU 29 July 2026 09:1429.07.2026 09:14
I'm starting to think I'm reaching the limits of what this little guy can do. Even though he feels like a big one, he's still just a small one and doesn't have that much mass. The other leaves should arrive today; let's see if they make a difference. Thanks for your feedback.
By the way, I managed to do four flights yesterday that didn't log anything and all had the same takeoff and landing times. They're available to view in the cloud.
machine-translated from German · Show original
MGU 30 July 2026 17:0830.07.2026 17:08
The problem seems to have been found; it was the main rotor blades. I replaced them with stiffer ones and there's no more Delofin noise, even at full pitch and flying straight ahead.
machine-translated from German · Show original
Eddi E. aus G. 31 July 2026 08:5431.07.2026 08:54
Good morning,

Great! How do the leaves differ, if at all, in length and geometry?
Curiosity :-) even though I don't have any myself.

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
MGU 31 July 2026 09:0331.07.2026 09:03
The length is the same, the geometry perhaps slightly different. The biggest difference is that the standard blades are made of reinforced PPA, while the new ones are carbon fiber blades, which are less flexible. My theory is that at high speeds, the helicopter oscillates due to the more flexible blades, and the control system can't compensate for this. (My theory :-)

What I do notice, however, is that there are increased vibrations when the motor is switched on and off with the carbon blades, but to be honest, I don't care about that because it's simply much more stable in flight.
machine-translated from German · Show original
Eddi E. aus G. 31 July 2026 10:3331.07.2026 10:33
Good morning,

The theory, or rather both together, is probably correct, thank you.

I wouldn't worry too much about increased vibration being logged; it probably only happens when there's a significant load anyway.

Have fun :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
MGU 31 July 2026 11:5831.07.2026 11:58
The vibration occurs once during the up and down spooling motion; I think the blades are the source, because it doesn't happen with the others. As I said, I don't care anymore, since it now flies straight and stable and isn't flipping anymore.
machine-translated from German · Show original
Eddi E. aus G. 31 July 2026 14:2531.07.2026 14:25
Oh, I see... well, that will result in different resonances, or the leaves are tighter (possibly too tight).

With the 200-size propeller, we also had to learn that just-loose (i.e., so that you can easily turn it in the blade holder but not yet tilt it up/down) is just tight enough, otherwise it would do something like that, or wobble in flight.

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless