← XL Power Support

Stratos 200 3 blade controller problems translated

OEM models › XL Power Support · Started by Sky on 30 September 2026 18:4230.09.2026 18:42
Sky 30 September 2026 18:4230.09.2026 18:42
Nice evening,

I have a new Stratos 3 blade with a VBar EVO Pro Rescue.

Setup for the three-blade propeller installed and two flights were flown yesterday without any problems.

I was really looking forward to flying it again today and starting with the fine-tuning.

The helicopter suddenly vibrates strongly, and the speed controller suddenly stops working properly. It pumps intermittently, and the RPM fluctuates.
Then everything runs smoothly again. And after a few seconds, everything is very bad again with the regulation.

Here's a lock from earlier. The helicopter is practically unflyable if you constantly have to adjust all the controls.

09/30/2026 5:58:51 p.m.;VBar Start -- STRATOS 200 -- 0027002514 -- V 8.2 -- pl 40
30.09.2026 17:58:51 Good; Cold start
30.09.2026 17:58:52 Good; Reset Reason: Power On
09/30/2026 5:58:52 p.m. Good; HW controller detected
30.09.2026 17:58:53 Good; Bank 1 loaded
30.09.2026 17:58:53 Warning; Initialization is being repeated...
30.09.2026 17:58:54 Warning; Initialization is being repeated...
30.09.2026 17:58:54 Warning; Initialization is being repeated...
30.09.2026 17:58:55 Warning; Initialization is being repeated...
30.09.2026 17:59:01 Good; Calibration complete
30.09.2026 17:59:22 Good; Top 5 battery choice: GensAce 750
30.09.2026 18:00:13 Info; Speed controller switched ON
30.09.2026 18:00:14 Good; Motor switch Motor On
30.09.2026 18:00:17 Warning; Rev controller at full throttle
30.09.2026 18:00:17 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:17 Warning; Rev controller at full throttle
30.09.2026 18:00:18 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:18 Warning; Rev controller at full throttle
30.09.2026 18:00:18 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:19 Warning; Rev controller at full throttle
30.09.2026 18:00:19 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:19 Warning; Rev controller at full throttle
30.09.2026 18:00:20 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:20 Good; Bank 2 loaded
30.09.2026 18:00:21 Warning; Rev controller at full throttle
30.09.2026 18:00:21 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:21 Good; Bank 1 loaded
09/30/2026 6:00:22 p.m. Info;Increased vibration level
30.09.2026 18:00:22 Warning; Rev controller at full throttle
30.09.2026 18:00:22 Warning; Rev controller at full throttle
30.09.2026 18:00:23 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:23 Warning; Rev controller at full throttle
30.09.2026 18:00:23 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:23 Warning; Rev controller at full throttle
30.09.2026 18:00:24 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:24 Warning; Rev controller at full throttle
30.09.2026 18:00:24 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:24 Warning; Rev controller at full throttle
30.09.2026 18:00:25 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:25 Warning; Rev controller at full throttle
30.09.2026 18:00:25 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:25 Warning; Rev controller at full throttle
30.09.2026 18:00:26 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:26 Warning; Rev controller at full throttle
30.09.2026 18:00:26 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:26 Warning; Rev controller at full throttle
30.09.2026 18:00:27 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:27 Warning; rev controller at full throttle
30.09.2026 18:00:27 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:27 Warning; rev controller at full throttle
30.09.2026 18:00:28 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:28 Warning; Rev controller at full throttle
30.09.2026 18:00:28 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:28 Warning; Rev controller at full throttle
30.09.2026 18:00:29 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:29 Warning; rev controller at full throttle
30.09.2026 18:00:29 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:29 Warning; rev controller at full throttle
30.09.2026 18:00:30 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:30 Warning; Rev controller at full throttle
30.09.2026 18:00:30 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:30 Warning; Rev controller at full throttle
30.09.2026 18:00:31 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:31 Warning; Rev controller at full throttle
30.09.2026 18:00:32 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:32 Warning; Rev controller at full throttle
30.09.2026 18:00:32 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:32 Warning; Rev controller at full throttle
30.09.2026 18:00:33 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:33 Warning; Rev controller at full throttle
30.09.2026 18:00:33 Warning; Rev controller at full throttle
30.09.2026 18:00:33 Warning; Rev controller at full throttle
30.09.2026 18:00:34 Warning; Rev controller at full throttle
30.09.2026 18:00:34 Warning; Rev controller at full throttle
30.09.2026 18:00:34 Warning; Rev controller at full throttle
30.09.2026 18:00:34 Warning; Rev controller at full throttle
30.09.2026 18:00:35 Good; Bank 2 loaded
30.09.2026 18:00:35 Warning; Rev controller at full throttle
30.09.2026 18:00:35 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:35 Warning; Rev controller at full throttle
30.09.2026 18:00:36 Warning; Rev controller at full throttle
30.09.2026 18:00:36 Warning; Strong vibration
30.09.2026 18:00:36 Warning; Rev controller at full throttle
30.09.2026 18:00:36 Warning; Rev controller at full throttle
30.09.2026 18:00:37 Warning; Rev controller at full throttle
30.09.2026 18:00:37 Warning; Rev controller at full throttle
30.09.2026 18:00:37 Warning; Rev controller at full throttle
30.09.2026 18:00:37 Warning; Rev controller at full throttle
30.09.2026 18:00:38 Warning; Rev controller at full throttle
30.09.2026 18:00:38 Warning; rev controller at full throttle
30.09.2026 18:00:38 Warning; Rev controller at full throttle
30.09.2026 18:00:38 Warning; Rev controller at full throttle
30.09.2026 18:00:39 Warning; rev controller at full throttle
30.09.2026 18:00:39 Warning; rev controller at full throttle
30.09.2026 18:00:39 Warning; rev controller at full throttle
30.09.2026 18:00:39 Warning; rev controller at full throttle
30.09.2026 18:00:40 Warning; Rev controller at full throttle
30.09.2026 18:00:40 Warning; Rev controller at full throttle
30.09.2026 18:00:40 Warning; Rev controller at full throttle
30.09.2026 18:00:40 Warning; Rev controller at full throttle
30.09.2026 18:00:41 Warning; Rev controller at full throttle
30.09.2026 18:00:41 Warning; Rev controller at full throttle
30.09.2026 18:00:41 Warning; Rev controller at full throttle
30.09.2026 18:00:41 Warning; Rev controller at full throttle
30.09.2026 18:00:42 Warning; Rev controller at full throttle
30.09.2026 18:00:42 Warning; Rev controller at full throttle
30.09.2026 18:00:42 Warning; Rev controller at full throttle
30.09.2026 18:00:42 Warning; Rev controller at full throttle
30.09.2026 18:00:43 Warning; Rev controller at full throttle
30.09.2026 18:00:43 Warning; Rev controller at full throttle
30.09.2026 18:00:43 Warning; Rev controller at full throttle
30.09.2026 18:00:43 Warning; Rev controller at full throttle
09/30/2026 6:00:44 p.m. Info;Increased vibration level
30.09.2026 18:00:44 Warning; Rev controller at full throttle
30.09.2026 18:00:44 Warning; Rev controller at full throttle
30.09.2026 18:00:44 Warning; Rev controller at full throttle
30.09.2026 18:00:45 Warning; Rev controller at full throttle
30.09.2026 18:00:45 Warning; Rev controller at full throttle
30.09.2026 18:00:45 Warning; Rev controller at full throttle
30.09.2026 18:00:45 Warning; Rev controller at full throttle
30.09.2026 18:00:46 Warning; Rev controller at full throttle
30.09.2026 18:00:46 Warning; Rev controller at full throttle
30.09.2026 18:00:46 Warning; Rev controller at full throttle
30.09.2026 18:00:47 Warning; Rev controller at full throttle
30.09.2026 18:00:47 Good; Bank 1 loaded
30.09.2026 18:00:47 Warning; Rev controller at full throttle
30.09.2026 18:00:48 Warning; Rev controller at full throttle
30.09.2026 18:00:49 Warning; Rev controller at full throttle
30.09.2026 18:00:49 Warning; Rev controller at full throttle
30.09.2026 18:00:49 Warning; Rev controller at full throttle
30.09.2026 18:00:50 Warning; Rev controller at full throttle
30.09.2026 18:00:50 Warning; Rev controller at full throttle
30.09.2026 18:00:50 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:51 Warning; Rev controller at full throttle
30.09.2026 18:00:51 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:51 Warning; Rev controller at full throttle
30.09.2026 18:00:51 Info; RPM controller is at the lower throttle limit
30.09.2026 18:00:52 Warning; Rev controller at full throttle
30.09.2026 18:00:52 Warning; Rev controller at full throttle
30.09.2026 18:00:52 Warning; Rev controller at full throttle
30.09.2026 18:00:52 Warning; Rev controller at full throttle
09/30/2026 6:00:52 p.m. Info;Increased vibration level
30.09.2026 18:00:53 Warning; Rev controller at full throttle
30.09.2026 18:00:53 Warning; Rev controller at full throttle
30.09.2026 18:00:53 Warning; Rev controller at full throttle
30.09.2026 18:00:53 Warning; Rev controller at full throttle
30.09.2026 18:00:54 Warning; Rev controller at full throttle
30.09.2026 18:00:54 Warning; Rev controller at full throttle
30.09.2026 18:00:54 Warning; Rev controller at full throttle
30.09.2026 18:00:55 Warning; Rev controller at full throttle
30.09.2026 18:00:55 Warning; Rev controller at full throttle
30.09.2026 18:00:55 Warning; Rev controller at full throttle
30.09.2026 18:00:56 Warning; Rev controller at full throttle
30.09.2026 18:00:56 Warning; Rev controller at full throttle
30.09.2026 18:00:56 Warning; Rev controller at full throttle
30.09.2026 18:00:57 Warning; Rev controller at full throttle
30.09.2026 18:00:57 Warning; Rev controller at full throttle
30.09.2026 18:00:57 Warning; Rev controller at full throttle
30.09.2026 18:00:58 Warning; Rev controller at full throttle
30.09.2026 18:00:58 Warning; Rev controller at full throttle
30.09.2026 18:00:58 Warning; Rev controller at full throttle
30.09.2026 18:00:59 Warning; Rev controller at full throttle
30.09.2026 18:00:59 Warning; Rev controller at full throttle
30.09.2026 18:00:59 Warning; Rev controller at full throttle
30.09.2026 18:01:00 Warning; Rev controller at full throttle
30.09.2026 18:01:00 Warning; Rev controller at full throttle
30.09.2026 18:01:00 Warning; Rev controller at full throttle
30.09.2026 18:01:01 Warning; Rev controller at full throttle
30.09.2026 18:01:01 Warning; Rev controller at full throttle
30.09.2026 18:01:01 Warning; Rev controller at full throttle
30.09.2026 18:01:01 Warning; Rev controller at full throttle
30.09.2026 18:01:02 Warning; Rev controller at full throttle
30.09.2026 18:01:02 Warning; Rev controller at full throttle
30.09.2026 18:01:03 Warning; Rev controller at full throttle
09/30/2026 6:01:03 PM Info;Increased vibration level
30.09.2026 18:01:03 Warning; Rev controller at full throttle
30.09.2026 18:01:03 Warning; Rev controller at full throttle
30.09.2026 18:01:04 Warning; Rev controller at full throttle
30.09.2026 18:01:04 Warning; Rev controller at full throttle
30.09.2026 18:01:04 Warning; Rev controller at full throttle
30.09.2026 18:01:04 Warning; Rev controller at full throttle
30.09.2026 18:01:05 Warning; Rev controller at full throttle
30.09.2026 18:01:05 Warning; Rev controller at full throttle
30.09.2026 18:01:05 Warning; Rev controller at full throttle
30.09.2026 18:01:06 Warning; Rev controller at full throttle
30.09.2026 18:01:06 Warning; Rev controller at full throttle
30.09.2026 18:01:06 Warning; Rev controller at full throttle
30.09.2026 18:01:07 Warning; Rev controller at full throttle
30.09.2026 18:01:07 Warning; Rev controller at full throttle
30.09.2026 18:01:07 Warning; Rev controller at full throttle
30.09.2026 18:01:08 Warning; Rev controller at full throttle
30.09.2026 18:01:08 Warning; Rev controller at full throttle
30.09.2026 18:01:08 Warning; Rev controller at full throttle
30.09.2026 18:01:09 Warning; rev controller at full throttle
30.09.2026 18:01:09 Warning; rev controller at full throttle
30.09.2026 18:01:09 Warning; rev controller at full throttle
30.09.2026 18:01:10 Warning; Rev controller at full throttle
30.09.2026 18:01:10 Warning; Rev controller at full throttle
30.09.2026 18:01:10 Warning; Rev controller at full throttle
30.09.2026 18:01:11 Warning; Rev controller at full throttle
30.09.2026 18:01:11 Info; Speed controller switched to OFF
30.09.2026 18:01:11 Info; Speed controller switched to idle
30.09.2026 18:01:11 Info; Off - Regulator - Umin: 11.2V Imax: 10.6A Temp: 44?
30.09.2026 18:01:12 Warning; Rev controller at full throttle
30.09.2026 18:01:12 Good; Motor switch Motor Off
30.09.2026 18:01:12 Good; Engine switch Idle Start
09/30/2026 6:01:13 PM Info;Increased vibration level
09/30/2026 6:02:04 PM;VBar Logfile End -- 9/30/2026 -- 6:02:04 PM
30.09.2026 18:02:04 Good;HW Controller Separated
machine-translated from German · Show original
Sky 30 September 2026 19:0830.09.2026 19:08
I found the solution in this thread: https://www.vstabi.info/forum/read.php?68,211528

It really is due to the rear-end sensitivity!

I wanted to optimize this one today, just like my Logo 200 V8 version (which flies great).

I've now set the tail sensitivity on all three banks of my new Stratos 200 3-blade helicopter to 22. That's the maximum setting; anything higher makes the helicopter unflyable.

I hope a solution is already being worked on.
machine-translated from German · Show original
Sky 30 September 2026 19:0930.09.2026 19:09
Here with rear sensitivity 22.

09/30/2026 6:54:56 p.m.;VBar Start -- STRATOS 200 -- 0027002514 -- V 8.2 -- pl 40
30.09.2026 18:54:56 Good; Cold start
30.09.2026 18:54:58 Good; Reset Reason: Power On
09/30/2026 6:54:58 p.m. Good; HW controller detected
30.09.2026 18:54:58 Good; Bank 1 loaded
30.09.2026 18:55:05 Good; Calibration complete
30.09.2026 18:55:07 Good; Top 5 battery choice: GensAce 750
30.09.2026 18:55:15 Good; Bank 2 loaded
30.09.2026 18:55:22 Good; Bank 3 loaded
30.09.2026 18:55:27 Good; Bank 1 loaded
30.09.2026 18:55:45 Info; Speed controller switched ON
30.09.2026 18:55:45 Good; Motor switch Motor On
09/30/2026 6:55:55 p.m. Info;Increased vibration level
30.09.2026 18:55:57 Warning; Rev controller at full throttle
09/30/2026 6:56:05 p.m. Info;Increased vibration level
30.09.2026 18:56:06 Good; Bank 2 loaded
09/30/2026 6:56:15 p.m. Info;Increased vibration level
30.09.2026 18:56:16 Good; Bank 3 loaded
30.09.2026 18:56:23 Warning; Rev controller at full throttle
30.09.2026 18:56:23 Warning; Rev controller at full throttle
30.09.2026 18:56:24 Warning; Rev controller at full throttle
09/30/2026 6:56:25 p.m. Info;Increased vibration level
30.09.2026 18:56:26 Good; Bank 2 loaded
30.09.2026 18:56:26 Good; Bank 1 loaded
09/30/2026 6:56:35 p.m. Info;Increased vibration level
30.09.2026 18:56:38 Warning; Rev controller at full throttle
09/30/2026 6:56:46 p.m. Info;Increased vibration level
30.09.2026 18:56:50 Warning; Rev controller at full throttle
09/30/2026 6:56:55 p.m. Info;Increased vibration level
09/30/2026 6:57:06 p.m. Info;Increased vibration level
30.09.2026 18:57:41 Info; Speed controller switched to OFF
09/30/2026 6:57:41 p.m. Info;Off - Controller - Umin:11.1V Imax:15.4A Temp:34?
30.09.2026 18:57:41 Good; Motor switch Motor Off
30.09.2026 18:57:43 Good; Bank 2 loaded
30.09.2026 18:57:47 Good; Bank 3 loaded
30.09.2026 18:57:50 Good; Bank 1 loaded
30.09.2026 18:57:50 Good; Bank 2 loaded
30.09.2026 18:57:51 Info; Speed controller switched ON
30.09.2026 18:57:51 Good; Motor switch Motor On
30.09.2026 18:57:59 Warning; rev controller at full throttle
30.09.2026 18:58:01 Good; Bank 2 loaded
30.09.2026 18:58:02 Warning; Rev controller at full throttle
30.09.2026 18:58:03 Warning; Rev controller at full throttle
09/30/2026 6:58:06 p.m. Info;Increased vibration level
30.09.2026 18:58:08 Good; Bank 1 loaded
30.09.2026 18:58:11 Info; Speed controller switched to idle
30.09.2026 18:58:12 Good; Engine switch Idle Start
09/30/2026 6:58:14 p.m. Info;Off - Controller - Umin:11.0V Imax:16.4A Temp:37?
30.09.2026 18:58:14 Info; Speed controller switched to OFF
30.09.2026 18:58:14 Good; Motor switch Motor Off
09/30/2026 6:58:17 p.m. Info;Increased vibration level
30.09.2026 18:59:47 Good; Bank 2 loaded
30.09.2026 18:59:48 Good; Bank 3 loaded
30.09.2026 18:59:50 Good; Bank 1 loaded
09/30/2026 7:00:31 PM;VBar Logfile End -- 9/30/2026 -- 7:00:31 PM
30.09.2026 19:00:32 Good;HW Controller Separated
machine-translated from German · Show original
Eddi E. aus G. 1 October 2026 10:1101.10.2026 10:11
Good morning,

I don't know if there's any other way to solve this than what's already known (link above).

Tail sensitivity and TTE influence this; high sensitivity and high TTE result in strong main engine control (torque extension to prevent the tail propeller from being relieved so much that the tail spins out), which eventually leads to the

30.09.2026 18:00:23 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:23 Warning; Rev controller at full throttle
30.09.2026 18:00:23 Info; Rev controller is at the lower throttle limit
30.09.2026 18:00:23 Warning; Rev controller at full throttle

back and forth.


Like pitch pumping on gas.

The load conditions are clearly different for the 3-blade system compared to the 2-blade system, and vary with different blades, which is understandable to some extent.
Then possibly another 4 seconds, a huge power surplus.
I think it's understandable that this causes (extreme) unrest.

The current solution is, for example, to lower the sensitivity so that a higher TTE can be used, or possibly to lower the TTE so that a higher sensitivity can be used.
But in my opinion, the TTE is what makes it special if you want to fly (very) performance-oriented and perhaps don't yet have, or want to have, a firm grasp of load management.

So... sensitivity 22 or somewhere around there (or try it out), and then adjust the TTE accordingly (try it out).

There probably won't be 'the' preset, because... too many variables, battery, blades, heads, a controller update at some point, etc. pp.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Sky 1 October 2026 10:2201.10.2026 10:22
Hi Eddi,

I have now done two flights with tail sensitivity set to 22.
The helicopter is new and powered by a 3s 750 GensAce battery.

It flies very well now.

The setting for tail rotor torque extension (I think this refers to TTE) is preset to 55 - 45 -45.

My next step will be to try and go a little higher.



Edited 2 time(s). Last edit at 10/01/2026 10:23AM by Sky.
machine-translated from German · Show original
Eddi E. aus G. 1 October 2026 10:3001.10.2026 10:30
Good morning,

TTE = Tail Torque Extension = Tail (rotor) torque extension, correct :-)

The default settings are 'always' what we (in this case) received from team drivers, at some point in the past of course, and possibly toned down a bit.
And then changes occur, and it may no longer fit properly, precisely because the working windows (in the sense of value ranges where parameters work well or optimally) are comparatively small in microcontrollers.

Yes, just try it :-) It's fun and quick and easy.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Sky 1 October 2026 12:0001.10.2026 12:00
Hi Eddi,

I tested something.

But the 55-45-45 configuration is best for the 3s 750mAh GensAce batteries.

During a recent flight with a slightly faster flying style, I suddenly had very little power and the controller kept beeping three times.

During another flight with a fresh battery, after about 1 minute of flight time, TicToc's motor suddenly stopped and the helicopter crashed into the tall grass.
The controller beeps three times again.

What's going on now?
machine-translated from German · Show original
Eddi E. aus G. 1 October 2026 13:1401.10.2026 13:14
Ola,

Um... check the logs?

:-)

I can take a look, but I'd need a serial number or two.

Regulators do what regulators do (e.g., throttling).
What does 3 beeps mean in HobbyWing?

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Sky 1 October 2026 13:5801.10.2026 13:58
Hi Eddi,

Nothing can be seen in the logos.

0027002514
Last flight went smoothly. Connectors were secured with hot glue.
Second to last, with regulator failure and crash in tall grass.
The second-to-last control is for a gentle reduction in engine speed and can no longer be changed. However, landing is still possible.

For both regulator problems, I increased the TTE: Bank 1 / 60, Bank 2 / 55, Bank 3 / 50.

Last flight went smoothly, everything was as it was when delivered, without any problems.

I will no longer change anything that could affect the controller's operation.
machine-translated from German · Show original
Eddi E. aus G. 2 October 2026 09:0502.10.2026 09:05
Good morning,

Yes, there's nothing particularly noticeable in it, I just quickly looked at the last 10 flight and controller logs.

The TTE values probably simply represent the limit for this helicopter given your flying style.

It would actually be interesting to know what the 3 blinks mean, whether one can learn anything from them.
Gentle throttling sounds more like a control function.
I suppose the controller itself doesn't log anything?

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Sky 2 October 2026 09:3002.10.2026 09:30
Good morning Eddi,

Possibly something to do with signal loss. I did a Google search.

But now everything is running smoothly.

It seems that as soon as something is changed that affects the motor control, the controller reacts very sensitively.

But I will no longer adjust the 55-45-45 setting on the TTE and will leave the rear sensitivity at 22.
Because as soon as a higher value is used for TTE, or for the rear sensitivity, the errors begin.

I was just so used to being able to adjust/modify the various parameters without risking a crash, like with the Logo 200 V8.

However, the software probably won't work well with the HobbyWing controller on the Stratos 200 three-blade motor. The adjustment range will be very narrow.


The Stratos now flies superbly with the VBar EVO.



Edited 1 time(s). Last edit at 10/02/2026 10:04AM by Sky.
machine-translated from German · Show original
Eddi E. aus G. 2 October 2026 12:2302.10.2026 12:23
Glad to hear it, sounds great :-)

It would be nice if Carl Henning S., who as far as I know wears the XL Power cap, would also have his say (*waves* with the picket fence ...).

:-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless