Andreas84
18 April 2025 11:2118.04.2025 11:21
Hello
How can I make the transition from Idle 1 to Idle 2 to Bailout a bit smoother? It's too abrupt when I flip the switch.
In Idle 1 I now have a speed of 1600 and in Idle 2 a speed of 2200, in Idle 3 is Bailout.
The transition from 1600 to 2200 should be much smoother.
How and where could I change or adjust that?
Set up:
IL Goblin Raw 700
VBar Neo Pro
YGE Opto 255
VBar regulation
Spektrum DX18
Thanks
Edited once. Last edited on 18.04.2025 at 11:52 by Andreas84.
Hallo
Wie kann ich denn Übergang von Idle 1 auf Idle 2 auf Bailout etwas smoother machen. Der hackt mir zu rasant rein wenn ich denn Schalter betätige.
Auf Idle 1 hab ich jetzt eine Drehzahl von 1600 und auf Idle 2 eine von 2200, auf Idle 3 ist Bailout.
Die übergang von 1600 auf 2200 sollte viel sanfter sein.
Wie und wo könnte ich das ändern bzw einstellen
Setup:
IL Goblin Raw 700
V-Stabi Neo Pro
YGE Opto 255
V-Stabi Regelung
Spektrum DX18
Danke
1 mal bearbeitet. Zuletzt am 18.04.2025 11:52 von Andreas84.
RV
18 April 2025 12:4118.04.2025 12:41
Basically, we switch between banks and the motor switch to 3 positions: Motor Off, AR, On, Bank 1, Bank 2, Bank 3 ;-)
Please describe it to us exactly as shown - what "Idle etc." means on your system is irrelevant here.
So, if you switch the motor switch (here: motor channel for external transmitter) from Off (-100) to On (+100), after the controller starts up, the ramp-up will continue as defined by the limiter (usually 3). Setting 2 would be even slower.
When the switch goes from On to AR (center, 0), it's essentially bailout standby. If you then switch back to On, the above limit multiplied by 10 always applies for the startup time. Therefore, if that's the case, set it to 2 and live with the compromise. Both processes will then be somewhat slower.
The art of an AR abort lies in not waiting until the blade stop to do it – but in making the decision in such a way that there's still enough time, perhaps a pirouette due to tail overload, nothing more. Everything else you just have to "carry through" to the ground.
The transitions within the RPMs during flying could possibly be masked with slightly less I - nothing more.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Grundsätzlich schalten wir Bänke um und den Motorschalter in 3 Stellungen. Motor Aus, AR, Ein, Bank1, Bank2, Bank3 ;-)
Bitte gib uns das so wieder - was dazu an Deiner Anlage "Idle usw." heißt ist hier egal.
Also - wenn Du den Motorschalter (hier: Kanal Motor für Fremdsender) von Aus (-100) nach Ein (+100) machst gehts nach dem ANlauf des Regler mit dem HOCHlauf definiert durch den Limiter (meist 3) weiter. Einstellung 2 wäre noch langsamer.
Wenn der von Ein nach AR (Mitte, 0) geht ist Bailout Standby quasi. Schaltet man dann nach Ein gilt immer obiges Limit mal 10 für den HOCHlauf. Insofern - wenn es das ist auf 2 stellen und mit dem Kompromiss leben. Wird dann eben beides was langsamer.
Die Kunst eines AR Abbruches besteht auch darin das nicht erst am Bladestop zu tun - sondern die Entscheidung so zu fällen dass es noch reicht, vielleicht eine Pirouette wegen Hecküberlastung, mehr nicht. Alles Andere muss man halt bis zum Boden "durchziehen".
Die Übergänge innerhalb der RPM's beim Fliegen könnte man ggf. mit etwas weniger I kaschieren - mehr nicht.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Andreas84
28 April 2025 09:3028.04.2025 09:30
Okay, I understand.
Actually, I wanted it to be like my old VBar.
Engine On/Off Bank 1 e.g. 1600, Bank 2 e.g. 2200 and Bank 3 Bailout
Is that no longer possible with the Neo?
Regards
Ok verstehe.
Eigendlich wollte ich das wieder so haben wie bei meinem alten v-stabi.
Motor Ein/Aus Bank 1 z.b 1600, Bank 2 z.B. 2200 und Bank 3 Bailout
Ist das beim Neo nicht mehr möglich?
Lg
Eddi E. aus G.
28 April 2025 10:0628.04.2025 10:06
Good morning,
The logic in NEO/EVO is standardized.
Engine Off
Engine idle (AR/Idle/Bailout) or, if programmed with VBar Control, Bank 4
. Engine On
Bank 1
... Bank2
.. Bank3
Slightly different (more consistent) than in 5.3 ...
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
die Logik bei NEO/EVO ist vereinheitlicht
. Motor Aus
. Motor Leerlauf (AR/Idle/Bailout) bzw. wenn mit VBar Control so programmiert Bank4
. Motor Ein
.. Bank1
.. Bank2
.. Bank3
Büschn anders (konsequenter) als bei 5.3 ...
Grüßle
Eddi
Born to fly ...
forced to work.