← Logo 700 and 800

The rear end twitches translated

Mikado Model Helicopters › Logo 700 and 800 · Started by maurice.krause on 10 March 2025 18:0810.03.2025 18:08
maurice.krause 10 March 2025 18:0810.03.2025 18:08
Hello everyone,

Since switching from a Vstabi NoVlink NEO to an EVO, I've had a problem with the tail. The settings have remained the same; here are my helicopter's specs:
This tail twitching only occurs during certain flight maneuvers.

I also have dangerous vibrations logged, but I haven't been able to determine their cause yet. Perhaps it's because I have the hard damping completely installed on the rotor head?

Logo 700 AZ700 Pro & AZ 105 Pro.
Engine Scorpion HK 4525-520 ULTIMATE
Hobbywing 200A with 8V BEC
Savöx SB-2290SG 3x swashplate
Savöx SB-2291SG tail servo
Vstabi EVO latest version 7.

Here's an unlisted link to YouTube:
https://youtu.be/NcTkDqAuAG8

Rear settings in the Vbar Control:
Expo: 28
Yaw Rate: 136
Gain: 77
Proportional: 88
Integral: 60
Coll. Precomp 60, 37, 45
Cycl. Precomp: 7
Optimizer ON

Thank you for your help in advance.

Greetings
Maurice
machine-translated from German · Show original
RV 10 March 2025 18:1210.03.2025 18:12
And when, where, and how am I supposed to see what in the video snippet?


Twitching at the rear in general... were the bearings of the pulleys electrically connected?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 10.03.2025 18:12 von RV.
machine-translated from German · Show original
maurice.krause 10 March 2025 18:2110.03.2025 18:21
RV wrote:
-------------------------------------------------------
And when, where, and how should I be in the video?
> What snippet should I see?
>
>
> Twitching at the rear end in general... were the bearings checked?
> Are the pulleys electrically connected?


Hi Rainer, in the video, I know you might not see it very well, it's only 3 seconds long, but you can hear it.

I don't quite follow your question about electrically conductive connections; if you mean the anti-static set, yes, I have installed that.

Greetings Maurice
machine-translated from German · Show original
Eddi E. aus G. 11 March 2025 09:1511.03.2025 09:15
Good morning,

Difficult to answer, 'it could be anything' :-)

. Antistatic (installed, OK)
Servo
Cable/plug
Motor/controller (cable/insulation/short circuit to ground; a twitching can also be seen at the rear)
other electrical effects (peaks)

I tried to find logs, but... nothing in the cloud.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
florian_neuner 11 March 2025 10:5011.03.2025 10:50
Hello Maurice,

With what frequency (Hz) are you controlling the tail servo?

If this is a silly question, have you ever tried simply turning down the gain on the rear gain?

Are you flying Vgov or the external Hobbywing Gov?

The Coll. Precomp seems quite high to me, how did you set it?

LG Flo



Edited once. Last edited on 11.03.2025 at 10:51 by florian_neuner.
machine-translated from German · Show original
maurice.krause 11 March 2025 17:5111.03.2025 17:51
Hello everyone,

Thanks for the replies so far. To answer @Eddi's question, how could I manually upload the data to the cloud?

@Florian I'm controlling the servos with 1520µs / 333Hz, I've already turned the gain down to 70, which got rid of the twitching, but then the servo wasn't reacting quickly enough.

I'm flying with Vgov.

I'm flying Mirko Cesena's setup, which I really liked with the Vstabi NEO, and well, the helicopter itself flies really great, I can't really complain, except for the tail twitching.

Thank you very much in advance for your help.

Greetings
Maurice
machine-translated from German · Show original
florian_neuner 11 March 2025 18:3511.03.2025 18:35
333Hz is the maximum for the Savöx servo, right?

What sensitivity setting do you have for vgov?

Unfortunately, you can't directly transfer the setup or values from a Neo to an EVO. It's possible, but since the EVO has much faster hardware, this results in different values, especially regarding sensitivities.

What exactly do you mean by the servo reacting too slowly?
machine-translated from German · Show original
maurice.krause 11 March 2025 18:4611.03.2025 18:46
Hi Florian,

I'm flying the Vgov with a sensitivity of 0.

By "counter-steering" I mean how long it takes until it locks into place; it's not an unimaginably long time, but because of this over-rotation, as I'll call it, the helicopter feels very uncomfortable.

Greetings
Maurice
machine-translated from German · Show original
florian_neuner 11 March 2025 18:5811.03.2025 18:58
Hi Maurice,

Interesting, may I ask why you're using vgov if you're flying with 0 gain? Then you're essentially flying without direct RPM control, but only with the cyclic and pitch adjustments.

Because if you say that it's gone at 70, that actually suggests that the gain is simply too high.
Did the "shaking" only disappear at 70 or did it also go away with higher gain?

Best regards

Flo
machine-translated from German · Show original
maurice.krause 11 March 2025 19:1111.03.2025 19:11
Hi Florian,

I fly the governor with 0 gain because, at higher sensitivity, I felt that the RPM was being regulated too much, meaning that more RPM was being given. This made the helicopter seem a bit unpredictable to me. I couldn't find anything really good about it, so I switched it to 0 and simply flew with the cyclic and pitch adjustments. I liked that so far with the 700 and 600 models, so I've kept it that way.

Regarding the tail sensitivity, it's difficult to explain; during some flight maneuvers, like in the short video or Tic Toc's, it starts to twitch, at 70 it's gone, at 77 it twitches.

However, I'm still wondering, couldn't I just set the gain to 70 and let the optimizer run? That should improve things, I think, because of the locking mechanism, right?

Greetings
Maurice
machine-translated from German · Show original
maurice.krause 11 March 2025 19:5911.03.2025 19:59
Eddi E. from G. wrote:
-------------------------------------------------------
> Hi,
>
> Difficult to answer, 'it could be anything' :-)
>
> . Antistatic (installed, OK)
> . Servo
> . Cable/plug
> . Motor/controller (cable/insulation/short circuit to ground, one
(You can also see the twitching at the rear)
> . other electrical effects (peaks)
>
I tried to find logs, but... nothing.
> the cloud.
>
> Greetings
>
> Eddie

Hi Eddi,

It would also be good if I activated the cloud service; I've left Vbar Control on for a few minutes now, I hope you find something useful.

Greetings
Maurice Krause
machine-translated from German · Show original
florian_neuner 11 March 2025 20:0711.03.2025 20:07
How did you configure the governor? Or did you just fly with the default settings?
Because if you don't have proper engine speed control, the rear end won't handle perfectly during load changes.

That's why I would perhaps start there.

The optimizer doesn't directly affect the detent behavior; you could try experimenting with the stop gains. You could also try leaving the gain as is and lowering the P value slightly to see if that makes a difference.

Best regards

Flo
machine-translated from German · Show original
maurice.krause 11 March 2025 20:3511.03.2025 20:35
Hi Florian,

I'll test it out in the next few days and get back to you.

Thanks for the help.

Greetings
Maurice
machine-translated from German · Show original
Eddi E. aus G. 12 March 2025 09:0512.03.2025 09:05
Good morning,

What is noticeable is that the controller is regularly fully open (100% PWM).
The rotational speed drops significantly.
This isn't regulation anymore, this is American-style chaos: full throttle, and let the battery handle it...

I would try loading the standard 700 setup, only re-entering the basic settings (e.g., trims), using the electric governor without changing anything, doing a trim flight, an optimizer flight, and then looking at/comparing the results.

Pilots' setups are often optimized for their needs/flying styles with their specific components, which doesn't always work well.
I've had some really extreme customer requests, everything's crap, setup by so-and-so, I can't fly like that... basic setup, OH! ... tweaked it a bit more, happy.

Then you can still see what the Pro Pilot may have adjusted, and try/compare individual settings in one or two banks.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
maurice.krause 13 March 2025 07:1813.03.2025 07:18
Hi Eddi,

I'll give that a try; I directly transferred the NEO setup to the EVO, so to speak. I now understand that it doesn't make much sense. If the weather permits, I'll try it out today.

Regards, Maurice
machine-translated from German · Show original
maurice.krause 13 March 2025 12:5213.03.2025 12:52
Hello everyone,

Yes, look at that, new setup, trim values adopted, trim flight performed, optimizer maxed out, tweaked the sensitivities and maneuverability a bit, and bam, everything's great, or almost...

I still have the problem that it easily takes 5-6 seconds before the motor starts to turn, so I flip the switch, put the pitch stick fully positive, wait 5-6 seconds and then it starts turning.

I selected Vgov again, telemetry to the Hobbywing 200A is working.
I still have dangerous vibrations, but the helicopter isn't causing any problems in that regard.

But otherwise I have to thank you, the 700 is now flying really well in principle.

Greetings
Maurice
machine-translated from German · Show original
Eddi E. aus G. 13 March 2025 13:2013.03.2025 13:20
Hi,

glad to hear.

Pitch stick fully positive, why? The ramp-up has nothing to do with it, please always ramp up at approximately 0°.

I'm not that familiar with WobbyHing, but perhaps the motor-off point in the setup can be used to better align the two points where the VBar starts its ramp-up and where the controller kicks in.

_Actually_, this should happen in a coordinated manner if you adjust the controller via telemetry...?

Perhaps Rainer has another idea?

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
RV 13 March 2025 14:3113.03.2025 14:31
If the hardware is programmed using our telemetry, there is no delay.

Try this:

Scroll down in Model Setup, then select the Gov Art, the HW menu will appear - and click.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
maurice.krause 13 March 2025 14:3613.03.2025 14:36
Hi,

Thanks for the reply, I'll test/check it tomorrow, it's pouring rain here.

Greetings
Maurice
machine-translated from German · Show original
maurice.krause 28 March 2025 15:5328.03.2025 15:53
RV wrote:
-------------------------------------------------------
> If the hardware is programmed using our telemetry
There will be no delay.
>
Try this:
>
> Scroll down in Model Setup, then select Gov Art
> select, the HW menu will appear - and click.


Hi Rainer,

I haven't had a chance to test it properly lately. In Gov Art, I selected HW (hardware). I can also configure the HW settings; it's configured exactly the same as my Logo 600, which turns on immediately. Do you have any other ideas what the problem could be?

Greetings
Maurice
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless