← Logo 700 and 800

Setup for new Logo 700 translated

Mikado Model Helicopters › Logo 700 and 800 · Started by maurice.krause on 9 May 2025 16:4309.05.2025 16:43
maurice.krause 9 May 2025 16:4309.05.2025 16:43
Hi everyone,

Since I now regret one or two things in the configuration of my first Logo 700...

My question is whether this is a competition-ready setup?
Answers from team pilots are also welcome.

New Logo 700
Hobbywing 260A Platinium Pro SBEC 12V
Scorpion HK5-5024-535kv
HLS Combo 12V KST Servo
Vstabi EVO Express 8.x
Vstabi EVO Pro Version
Power Backup Vstabi

Greetings
Maurice

machine-translated from German · Show original
florian_neuner 29 May 2025 10:1329.05.2025 10:13
Hi Maurice,

That sounds good!
I can't personally say anything about the engine, but to my knowledge Marik and Mariano also fly it.
I fly the 4525 xNova, which is significantly lighter.
I use this controller myself in my competition setup and I'm completely satisfied.
I have the 12V HLS from KST in my test helicopter, and they work perfectly. As far as I know, Carl also uses them in his competition setups.
So I don't think there's anything wrong with that :-)

LG Flo



Edited once. Last edited on 29.05.2025 at 10:21 by florian_neuner.
machine-translated from German · Show original
maurice.krause 29 May 2025 12:1029.05.2025 12:10
Hi Flo,

Thanks for the reply, yes, some time has passed, I'm currently flying my 700 with the Xnova 4525-560KV, absolutely awesome piece of kit, at the moment I'm just missing a 14-tooth pinion gear.

Greetings
Maurice
machine-translated from German · Show original
florian_neuner 29 May 2025 13:2529.05.2025 13:25
Hi Maurice,

With the 560kv motor, a 14-tooth pinion would be a bit overkill. I use the 14-tooth pinion on my 530kv motor, which works perfectly for me so the whole drivetrain runs efficiently (it does drop off a bit with older batteries, but I'm happy to accept that to reduce the peak currents).
What RPM are you flying at?

LG Flo
machine-translated from German · Show original
maurice.krause 29 May 2025 13:4929.05.2025 13:49
Hi Flo,

I usually fly at around 2060-2100 RPM, depending on the batteries I'm using. My "best" batteries are 5100mAh 55C. Could these be the bottleneck? I often experience dips in power at 2100 RPM.

Greetings
Maurice
machine-translated from German · Show original
HeliALEX 29 May 2025 23:4629.05.2025 23:46
Hello Maurice,

What exactly is shown in the flight summary at the end?
Is the controller often/permanently set to 100%?

Regarding the first post: we also fly the HK5 5024-535 with a 14-tooth pinion, 2200 RPM and without any dips in performance. Did you perhaps have the 13-tooth pinion installed on that motor?
A 4525 motor generally has significantly less torque compared to the HK5-5024; if you put the 14-inch propeller on a 560KV motor (quite high in the 700 series), the temperature and your current peaks will increase significantly.
machine-translated from German · Show original
maurice.krause 30 May 2025 08:3730.05.2025 08:37
Hi HeliALEX,

Thanks for the reply, I then continued writing with Flo on Instagram, the solution was actually quite simple, readjusted the base throttle, adjusted the throttle distance from the controller and lo and behold, no more RPM drops.

Greetings
Maurice
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless