maurice.krause
25 April 2025 13:3625.04.2025 13:36
Hello everyone,
I switched from my Savöx 1258TG servos to Savöx 2271 servos because of the high voltage (HV) feature. Now my problem is that I can't tighten these servos properly anymore, obviously because the sheet metal screws have already screwed into the plastic. Is there any way to tighten them properly again? Loctite?
Greetings
Maurice
Hallo zusammen,
ich bin von meinen Savöx 1258TGs auf Savöx 2271er umgestiegen wegen HV, nun ist mein Problem, dass ich diese Servos nicht mehr richtig festdrehen kann, klar, weil ja auch die Blechschrauben sich schon einmal in das Plastik reingedreht haben, gibt es eine möglichkeit das wieder richtig fest zubekommen? Loctite?
Grüße
Maurice
RV
26 April 2025 07:4326.04.2025 07:43
What kind of screws do you have? Hex socket or Phillips head?
In my experience, I can reuse the holes several times.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Welche Schrauben hast Du denn? Mit Innensechskant oder Kreuzschlitz?
Erfahrungsgemäß kann ich die Löcher gut mehrfach verwenden.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
maurice.krause
26 April 2025 09:0926.04.2025 09:09
I have the Phillips head screws supplied by Savöx; I couldn't find the Allen screws from the kit.
Greetings
Maurice
Ich hab die von Savöx mitgelieferten Kreuzschlitz Schrauben, die innensechskant Schrauben von dem Baukasten konnte ich nicht finden.
Grüße
Maurice
RV
26 April 2025 19:0826.04.2025 19:08
Hmm... are those the slightly tapered ones? Could you measure the inner diameter just before the shaft, and the outer diameter as well?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hmmm ... sind das die leicht konischen? kannst mal den Innendurchmesser kurz vorm Schaft messen und den Außendurchmesser auch?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
maurice.krause
27 April 2025 08:5627.04.2025 08:56
Hi Rainer,
Approx. 2.9 mm shaft diameter
approx. 5.5–6 mm head diameter
The problem has been solved, though; we had some thicker screws from our model crane project, so now the servo is really secure and we can start testing today :-)
Greetings
Maurice
Moin Rainer,
ca. 2,9 mm Schaftdurchmesser
ca. 5,5–6 mm Kopfdurchmesser
das Problem hat sich aber erledigt, wir hatten durch unser Modellbaukran Projekt noch etwas dickere Schrauben, jetzt sitzt das Servo richtig fest und es kann heute an´s testen gehen :-)
Grüße
Maurice