maurice.krause
27 April 2025 18:2327.04.2025 18:23
Hello everyone,
Yes, yes, it's a never-ending story...
I've had my brand new Logo 600 (aluminum head) for about 2 months now and I've only had problems so far. First, the setup:
Motor: Scorpion HK-4035-450KV
ESC: Hobbywing 180A (Previously 6V, now 8.4V)
Previously: Savöx 1258TG+ and 1290MG+
Now: Savöx 2271SG+ and 2272MG+
Vstabi EVO aluminum housing.
Now, here's my problem: before the servo upgrade, I already had the issue of my tail oscillating/vibrating. Then I upgraded to HV servos, which was another expensive investment. Unfortunately, there's no difference; it still behaves exactly the same way. And that's where I find it puzzling: why do I have the exact same problem with better servos?
Which points have I already completed:
Incorrect servos
Strap too tight
Strap too loose
The rear linkage has resistance.
Different sensitivities
Pendulum suppression etc. etc.
Leaves weighed.
I'm absolutely certain, and it simply needs to be said clearly that it's no longer any fun at all.
I'm also experiencing strong vibrations; yes, I know the vibrations are more pronounced through the aluminum housing. I want to emphasize again that everything moves smoothly, the helicopter was assembled exactly according to the instructions, all trim values were mechanically adjusted so that no further trimming was necessary, and all endpoint and maximum values are nearly identical.
I have had the Vstabi since February 17, 2025; if it is offered to me, I would consider having it tested under warranty.
Greetings :-)
Maurice
Edited once. Last edited on 27.04.2025 at 18:25 by maurice.krause.
Hallo zusammen,
ja ja, es ist eine never ending story...
Ich habe seit ca. 2 monaten meinen nagelneuen Logo 600 (Alu Kopf) und ich habe bisher nur Probleme, zum Setup erstmal:
Motor: Scorpion HK-4035-450KV
Regler: Hobbywing 180A (Früher mit 6V, jetzt mit 8,4V)
Früher: Savöx 1258TG+ und 1290MG+
Jetzt: Savöx 2271SG+ und 2272MG+
Vstabi EVO Alu Gehäuse.
Nun mein Problem, ich hatte vor dem Servo Upgrade schon das Problem das mein Heck pendelte/zitterte, dann hatte ich auf die HV Servos geupgraded, was natürlich nochmal eine teure Investition war. Leider gibt es kein unterschied, immernoch genau das selbe Verhalten und da kommt der Punkt den ich fragwürdig finde, warum habe ich bei besseren Servo, genau das gleiche Problem.
Welche Punkte habe ich bereits abgearbeitet:
Falsche Servos
Riemen zu stramm
Riemen zu locker
Heckgestänge hat ein widerstand
Verschiedene Empfindlichkeiten
Pendelunterdrückung etc etc.
Blätter gewogen.
Ich bin echt fraglos und man muss einfach mal ganz klar sagen das es überhaupt kein spaß mehr macht.
Ich habe zudem auch starke Vibrationen, ja ich weiß durch das Alu Gehäuse gehen die Vibrationen mehr durch. Ich betone nochmal, alles ist leichtgängig, der Heli wurde genau nach Anleitung aufgebaut, alle Trim werte wurde mechanisch so angepasst das nicht getrimmt werden musste, alle Werte bzgl. Endpunkte bzw. Max. Werte sind nahezu identisch.
Das Vstabi habe ich seit dem 17.02.2025, wenn es mir angeboten wird, würde ich eine Prüfung innerhalb einer Garantie in Erwägung ziehen.
Grüße :-)
Maurice
1 mal bearbeitet. Zuletzt am 27.04.2025 18:25 von maurice.krause.
RV
27 April 2025 18:5727.04.2025 18:57
Hello Maurice,
What pulse length/frame rate have you set on the tail servos? Are they servos with a long or short center pulse?
Personal note:
The Savox servo on the tail has always been a bit "rough" in its control response. I prefer to install other servos, e.g., KST, and only use a short center pulse and a 1000Hz setting on the VBar EVO.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hallo Maurice,
welche Pulslänge/Framerate hast Du denn am Heck eingestellt? Sind das Servos mit langem oder kurzem Mittenpuls?
Persönliche Anmerkung:
Savox am Heck war schon immer was "rauh" in der Regelung vom Servo an sich aus. Ich baue gerne andere, z.B. KST ein und nur noch mit kurzem Mittenpuls und 1000Hz Einstellung an VStabi EVO.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
maurice.krause
27 April 2025 19:4827.04.2025 19:48
Hello Rainer,
In Vstabi I set the following: 333Hz 1500/1520µs.
Greetings
Maurice
Hallo Rainer,
im Vstabi hab ich folgendes eingestellt: 333hz 1500/1520?µs.
Grüße
Maurice
RV
27 April 2025 22:2827.04.2025 22:28
If you have a VBar EVO, my recommendation would be to set a servo with a short center pulse and 760us/1000Hz.
However, this requires a different servo - one that has this short center pulse (750/760us).
Otherwise – what's always important is smooth mechanical operation. The installation direction of the thrust bearings is also important. And then I've also had colleagues with poorly bonded control rods.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Wenn Du eine VStabi EVO hast - wäre meine Empfehlung ein Servo mit kurzem Mittenpuls und 760us/1000Hz einzustellen.
Das bedingt allerdings ein anderes Servo - welches diesen kurzen Mittenpuls (750/760us) hat.
Ansonsten - was immer wichtig ist wäre mechanische Leichtgängigkeit. Auch Verbaurichtung der Drucklager ist wichtig. Und dann hatte ich auch schon Kollegen mit schlechter Verklebung der Steuerstangen.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
maurice.krause
28 April 2025 07:2128.04.2025 07:21
Hello Rainer,
Thanks for the tips!
Which KST servo would you recommend for the Logo 600?
For example: A KST SV905-12?
Greetings
Maurice
Hallo Rainer,
danke für die Tipps!
Welches KST Servo könntest du mir denn für den Logo 600 empfehlen?
Bspw: Ein KST SV905-12?
Grüße
Maurice
RV
28 April 2025 08:1928.04.2025 08:19
I installed a 12V set in each of the 3 helicopters.
I need to take a look at what corresponds to that.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Ich habe in allen 3 Helis je ein 12V Set verbaut.
Muss mir das mal ansehen was dem entspricht.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV
28 April 2025 19:1828.04.2025 19:18
So, the proposed KST servo would be good, but it's a 12V servo. Therefore, the TS servos and the BEC also need to supply 12V.
Either stay at 8.4V or use a complete 12V system - mixing makes no sense.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Also - das vorgeschlagene KST wäre ja schon gut - ist aber ain 12V Servo. Insofern müssen dann die TS Servos und das BEC auch die 12V bringen.
Entweder bei 8,4V bleiben oder Kpl 12V - Mischen macht keinen Sinn.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
maurice.krause
28 April 2025 19:1928.04.2025 19:19
Hello Rainer,
I think I've identified the problem; the freewheel had extreme resistance, maybe that's related. Attached is a screenshot from the assembly instructions: This screw was way too tight.
Now I have a completely new problem: the rear end spins out uncontrollably, simply away.
I had a similar problem once, back with the Logo 700, still using my Spektrum DX9; it was simply reversed. Maybe Eddi remembers that.
But is there even an option for that in the Vbar Control? As far as I know, it's only via the model setup.
By the way: Luckily, nothing broke or snapped.
Here are two more links.
https://youtube.com/shorts/-ZhgYuE1y58?feature=share https://youtu.be/JTXqprMoxA4 Greetings
Maurice
Hallo Rainer,
ich glaube ich hab das Problem erkannt, der Freilauf hatte ein extremen Widerstand, vielleicht hängt das ja zusammen. Anbei Screenshot von Bauanleitung: Diese Schraube war viel zu fest.
jetzt habe ich ein ganz neues Problem, das Heck dreht unkontrolliert, einfach weg.
Ich hatte mal ein ähnliches Problem, damals beim Logo 700, noch mit meiner Spektrum DX9, da war es einfach reversed, vielleicht erinnert sich Eddi noch daran.
Aber gibt es bei der Vbar Control dafür überhaupt eine Option? Soweit ich weiß ja nur über das Model Setup.
BTW: Es ist zum Glück nichts kaputt gegangen oder abgebrochen.
Hier noch 2 Links.
https://youtube.com/shorts/-ZhgYuE1y58?feature=share
https://youtu.be/JTXqprMoxA4
Grüße
Maurice
maurice.krause
28 April 2025 19:2228.04.2025 19:22
Here's another message so you can see it; our messages just crossed.
Greetings
Maurice
Hier nochmal eine Nachricht, damit du es siehst, unsere Nachrichten haben sich gerade überschnitten.
Grüße
Maurice
maurice.krause
28 April 2025 23:2028.04.2025 23:20
maurice.krause wrote:
-------------------------------------------------------
Hello Rainer,
>
I think I've identified the problem, the
The freewheel had extreme resistance, perhaps
> That's all connected. Attached is a screenshot of
> Assembly instructions: This screw was much too tight.
>
Now I have a completely new problem, the rear end
> spins uncontrollably, simply away.
I had a similar problem once, back when...
> Logo 700, still with my Spektrum DX9, that's when it was
Simply reversed, maybe Eddi remembers.
> still on it.
>
But is there a Vbar Control option for that?
Is that even an option? As far as I know, only yes.
> about the model setup.
>
> By the way: Luckily nothing was broken or
> aborted.
Here are two more links.
>
>
https://youtube.com/shorts/-ZhgYuE1y58?feature=sha > re
>
https://youtu.be/JTXqprMoxA4 >
Greetings
> Maurice
The thought just came to me in bed: when I checked why the freewheel was causing resistance, I put the timing belt on backwards, 90° in the wrong direction, which should cause the tail rotor to turn in the wrong direction...
That's pretty stupid, but yeah, at least nothing happened.
Greetings
Maurice
maurice.krause schrieb:
-------------------------------------------------------
> Hallo Rainer,
>
> ich glaube ich hab das Problem erkannt, der
> Freilauf hatte ein extremen Widerstand, vielleicht
> hängt das ja zusammen. Anbei Screenshot von
> Bauanleitung: Diese Schraube war viel zu fest.
>
> jetzt habe ich ein ganz neues Problem, das Heck
> dreht unkontrolliert, einfach weg.
> Ich hatte mal ein ähnliches Problem, damals beim
> Logo 700, noch mit meiner Spektrum DX9, da war es
> einfach reversed, vielleicht erinnert sich Eddi
> noch daran.
>
> Aber gibt es bei der Vbar Control dafür
> überhaupt eine Option? Soweit ich weiß ja nur
> über das Model Setup.
>
> BTW: Es ist zum Glück nichts kaputt gegangen oder
> abgebrochen.
> Hier noch 2 Links.
>
>
https://youtube.com/shorts/-ZhgYuE1y58?feature=sha
> re
>
https://youtu.be/JTXqprMoxA4
>
> Grüße
> Maurice
Gerade im Bett kam der Gedankensblitz, ich hab bei der Kontrolle warum der Freilauf ein widerstand hat, den Zahnriemen, falsch rum drauf gemacht, also 90° in die falsche Richtung, dadurch müsste ja der Heckrotor falsch herum gedreht werden...
Das ist nun ziemlich dämlich, aber ja, immerhin ist nichts passiert.
Grüße
Maurice
RV
29 April 2025 05:5129.04.2025 05:51
So - when the helicopter starts spinning, the tail rotor must rotate "upwards to the rear" here.
You can also check this by hand on the workbench - but due to the freewheel, you turn the main rotor counterclockwise and the tail rotor must also go "top to front".
A question about the pendulum effect, since we're on the subject: Is the tail rotor assembled correctly, are the blades mounted correctly? Photo?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 29.04.2025 05:51 von RV.
Also - wenn der Heli andreht muss der Heckrotor hier "oben nach hinten" drehen.
Auf der Werkbank kann man das auch von Hand prüfen - aufgrund des Freilaufes dreht man da dann aber den Hauptrotor linksrum und der Heckrotor muss ebenso dann "oben nach vorne" gehen.
Frage zum Pendeln weil wir grad da dran sind: Heckrotor ist richtig aufgebaut, Blätter richtig montiert? Foto?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 29.04.2025 05:51 von RV.
maurice.krause
29 April 2025 07:5229.04.2025 07:52
Hi Rainer,
Yes... it's exactly the opposite of what you described, so I definitely put the belt on backwards.
Regarding the photo request, here are 3 photos; I hope you can see everything in them.
Greetings
Maurice
Moin Rainer,
ja... es ist genau andersrum als du es beschrieben hast, also habe ich definitiv den Riemen falsch rum drauf.
Wegen der Foto Anfrage, hier 3 Fotos, hoffe du kannst alles darauf erkennen.
Grüße
Maurice
maurice.krause
29 April 2025 10:1729.04.2025 10:17
Just one more small note: the helicopter is flying again; apparently the belt was on backwards. I've saved the information for next time so that this doesn't happen again.
Surprisingly, the tail is quite stable; I'm currently at about 70-80 sensitivity, very happy with the tail, but I still have the problem that the tail rotates when pitching. I tried the Pitch Pump option with values between 0-60, but it didn't really help. My controller is set to 30 sensitivity.
The rear limit is set to 70 on both the left and right sides in the setup; could this value be too low? Meaning that the rear end doesn't have enough travel to swing out?
Greetings
Maurice
Edited once. Last edited on 29.04.2025 at 10:22 by maurice.krause.
Nochmal eine kleine Anmerkung, Heli fliegt wieder, offensichtlich war der Riemen falsch rum, wurde für´s nächste mal gespeichert, damit sowas nicht nochmal passiert.
Heck ist erstaunlicherweise ziemlich ruhig, bin jetzt ca bei 70-80er Empfindlichkeit, sehr zufrieden mit dem Heck, nur hab ich nun noch immer das Problem das sich das Heck bei Pitch wegdreht, die Option Pitch Pump hab ich mal ausprobiert mit Werten zwischen 0-60, hat nicht wirklich was gebracht, Regler ist bei mir auf 30er Empfindlichkeit.
Heck Limit ist Links und Rechts im Setup auf 70, kann es sein das der Wert zu wenig ist? Im Sinne von, dass das Heck nicht genug Weg zum ausschlagen hat?
Grüße
Maurice
1 mal bearbeitet. Zuletzt am 29.04.2025 10:22 von maurice.krause.
Eddi E. aus G.
29 April 2025 12:2029.04.2025 12:20
Hi Maurice,
First of all: good :-)
Then... lots of trying, but not knowing what's what ^^ we can help with that.
Pitch pump amplifies and exaggerates rapid pitch movements. It is only indirectly related to tail rotation.
The controller sensitivity as well.
Paths... are set up so that you have roughly the same number in both directions (example: 85-95 OK, 60-120 not OK).
And in such a way that one has reasonable aerodynamic angles of attack (for example, 25-30° OK, 45° not OK), so that one can expect the maximum effect, but no flow separation.
The parameters you should look at are:
Rear/Expert/DMA Pitch: here, the rear end is controlled simultaneously with pitch to proactively anticipate the increasing torque.
DMA cyclic: the same applies to cyclic inputs.
Fly it out: from hovering flight to a rapid climb, adjust until the tail no longer turns away.
Rolls or flips from a hover, same principle. Or... set approximately 1/3 of the DMA pitch, that usually works quite well.
Grüßle
Eddi
Born to fly ...
forced to work.
Hi Maurice,
erst mal: gut :-)
Dann ... viel Probieren, aber nicht wissen was was ist ^^ dem können wir abhelfen.
Pitch-Pump verstärkt-überzeichnet schnelle Pitchbewegungen. Hat mit dem Wegdrehen des Hecks nur indirekt zu tun.
Die Regler-Empfindlichkeit ebenso.
Wege ... die stellt man so ein, dass man in beide Richtungen etwa gleich große Zahlen hat (Beispiel, 85-95 OK, 60-120 nicht OK).
Und dabei so, dass man vernünftige aerodynamische Anstellwinkel hat (Beispiel, 25-30° OK, 45° nicht OK), so dass man die maximale Wirkung erwarten kann, aber keinen Strömungsabriss.
Die Parameter, die Du Dir anschauen solltest:
Heck/Expert/DMA Pitch: hier wird bei Pitch gleichzeitig Heck gesteuert, um dem ansteigenden Drehmoment vorausschauend zuvor zu kommen.
DMA zyklisch: das selbe, bei zyklischen Inputs.
Erfliegen: aus dem Schwebeflug einen zügigen Steigflug, anpassen, bis das Heck nicht mehr wegdreht.
Aus dem Schwebeflug Rollen oder Überschläge, das selbe. Oder ... ungefähr 1/3 vom DMA Pitch einstellen, das passt i. d. R. ganz gut.
Grüßle
Eddi
Born to fly ...
forced to work.
maurice.krause
29 April 2025 14:1029.04.2025 14:10
Hi Eddi,
Thanks for the reply, but sorry, I can't find the DMA Pitch option in my Vbar Touch.
Greetings
Maurice
Hi Eddi,
danke für die Antwort, entschuldige aber, ich finde die Option DMA Pitch in meiner Vbar Touch nicht.
Grüße
Maurice
RV
29 April 2025 17:2429.04.2025 17:24
Flight parameters, tail rotor, scroll down ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Flugparameter, Heckrotor, runterscrollen ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
maurice.krause
1 May 2025 08:3901.05.2025 08:39
Hi everyone, first of all, I wish you a happy May 1st.
Here's a short video:
https://youtu.be/b1GySDHj2Bg I can't find the DMA Pitch option.
Or do I need to connect the Vstabi to a PC and configure it via the PC?
Greetings
Maurice
Edited once. Last edited on 01.05.2025 at 08:39 by maurice.krause.
Hi zusammen, erstmal wünsch ich euch einen schönen 1. Mai.
Hier ein kleines Video:
https://youtu.be/b1GySDHj2Bg
Ich finde die Option DMA Pitch nicht.
Oder muss ich das Vstabi an PC anschließen und es über den PC einstellen?
Grüße
Maurice
1 mal bearbeitet. Zuletzt am 01.05.2025 08:39 von maurice.krause.
RV
1 May 2025 10:1801.05.2025 10:18
That's pitch precompensation ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Pitch Prekompensation ist das ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
maurice.krause
1 May 2025 14:5801.05.2025 14:58
Thank you, Rainer!
Greetings
Maurice
Dankeschön Rainer!
Grüße
Maurice