← Logo 400 ... 690

Logo 600 maximum rotor blade length translated

Mikado Model Helicopters › Logo 400 ... 690 · Started by maurice.krause on 24 May 2025 17:1224.05.2025 17:12
maurice.krause 24 May 2025 17:1224.05.2025 17:12
Hello everyone,

Unfortunately, I couldn't find any precise information regarding the maximum length of the tail rotor blades for the Logo 600. I still have the problem that my tail spins out when I adjust the pitch, no matter what I set; nothing really changes. Furthermore, in certain maneuvers with pitch/yaw combinations, the tail sometimes seems to stand still.

My suspicion is that the 95mm Azure Blades on the tail rotor aren't generating enough power; could I, for example, simply try 105mm blades?

Greetings
Maurice
machine-translated from German · Show original
Bernhard Kerscher 26 May 2025 08:3826.05.2025 08:38
Hello Maurice,
Please check the following: hold the rotor head firmly and try to turn the tail rotor head.
I hope nothing rotates here and slips under load.
This can happen if, for example, the pin in the rear belt pulley is missing or has slipped.
Or the pulley at the front is broken and the drive pin is spinning freely.
If it's a genuine L600 with an aluminum pulley, that's rather unlikely.
But please take a close look at the belt drive.
Also the clamping screw from the rear hub.
Greetings Bernhard
machine-translated from German · Show original
maurice.krause 26 May 2025 18:1626.05.2025 18:16
Hi Bernhard,

First of all, thank you for the answer.

I just checked it, everything's fine, the helicopter has maybe been flown 5 times, the kit is about 1 year old, it's the Logo 600 (aluminum head), I don't know if you thought it was the Logo 600 3D.

Greetings
Maurice
machine-translated from German · Show original
Bernhard Kerscher 27 May 2025 08:5927.05.2025 08:59
Good morning,
No, I just wanted to know if it's the L600 with an aluminum head and therefore an aluminum pulley, or the 600 SX with a plastic pulley.
But you've already answered that.
Greetings Bernhard



Edited once. Last edited on 27.05.2025 at 08:59 by Bernhard Kerscher.
machine-translated from German · Show original
maurice.krause 29 May 2025 07:2929.05.2025 07:29
Hello again everyone,

What's the maximum length now? I still have the Rotortech propellers from my 700 lying around here; they're 105mm. Can I just screw them onto the 600?

Happy holiday to you all!

Greetings
Maurice
machine-translated from German · Show original
ikarus991 29 May 2025 12:0529.05.2025 12:05
You can't really say for sure, it also depends on the main rotor blades.
- the leaves should not be able to touch each other
- Rear blades must not touch the ground

I have 105 on my 550....

wolfgang
machine-translated from German · Show original
maurice.krause 29 May 2025 13:5029.05.2025 13:50
Hi everyone,

The solution was indeed the 105mm blades; the 600mm blade remains almost still and no longer spins away.

Greetings
Maurice Krause
machine-translated from German · Show original
maurice.krause 23 June 2025 09:4623.06.2025 09:46
Hi everyone,

Never-ending story... I can't get the Logo 600 adjusted. The tail doesn't sway much anymore, but it's still there, and it's very annoying in some maneuvers.

I fly with the tail against the torque, that's how I learned it, but in many maneuvers with pitch and tail movements, it seems as if it doesn't have enough power. I have the Savöx 2292+ installed, so it should have enough power.

Is there any way I could have you take a look at it? I'm from the Odenwald region; I think @Rainer Vetter is from nearby, right?

I really don't have the energy anymore to mess around with the 600.

Yesterday I was at MFG Elsava, you should know Ingmar Grote, unfortunately he's also at his wit's end.
If the opportunity arises, I would also be willing to travel to you.

Perhaps something can be done about it.

Greetings
Maurice

============================================================
Logo 700 - Logo 600 - Vbar EVO/Touch
https://www.youtube.com/@mauricekrause
machine-translated from German · Show original
Eddi E. aus G. 23 June 2025 09:5323.06.2025 09:53
Hi Maurice,

Unfortunately not for the next few weeks, due to vacation, a private move, ...

A few things to keep you busy in the meantime: I would try a different (completely different, it doesn't really matter which one) tail servo, ideally one with at least a narrow pulse (760 µs) and a 333 Hz frequency. The rest of the technical specifications aren't important to me for this test, as long as it's not a sail winch...

And, if someone nearby has a suitable LOGO, try swapping the entire tail rotor (hub with blade holders, blades and everything).

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
maurice.krause 23 June 2025 09:5623.06.2025 09:56
Hi Eddi,

Thanks for the reply, I wanted to buy something from KST anyway, also because of the new Logo 700, so I'll order a fast x20 for the rear with 760 µs.

Greetings
Maurice

============================================================
Logo 700 - Logo 600 - Vbar EVO/Touch
https://www.youtube.com/@mauricekrause
machine-translated from German · Show original
Eddi E. aus G. 23 June 2025 10:2723.06.2025 10:27
Good morning,

And regarding the tail fins, the NHP 105 mm were simply weapons. If you can still get your hands on some... I think they're no longer manufactured, but check eBay or somewhere similar (of course, there's still some risk involved).

I personally got along just fine with EDGE in the past and Rotortech currently, but maybe your heli is just a diva :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
maurice.krause 23 June 2025 10:3123.06.2025 10:31
Hi,

Yeah, that heli's definitely a diva xD. I was thinking of just taking my Savöx Monster from the 700 and installing it in there. If that doesn't work, the 600 will just have to wait until the new 700 comes out. Because my current 700 flies really smoothly. I need to correct myself, though; I have the Savöx 2272+ in the Logo 600, and the 700 has the 2292.

Let's wait and see what the future holds.

Greetings
Maurice

============================================================
Logo 700 - Logo 600 - Vbar EVO/Touch
https://www.youtube.com/@mauricekrause
machine-translated from German · Show original
maurice.krause 30 June 2025 16:5630.06.2025 16:56
Hi everyone,

Yes, unfortunately no success. So, to first address Eddi's advice, unfortunately I don't know anyone who still has a Logo 600 from which I could take the rear end.

But I tried the 2292 from the 700 series and unfortunately it behaved exactly the same way. My suspicion would be the belt; I heard somewhere that you're supposed to hold the entire ready-to-fly helicopter by the tail and then tighten the screws at the tail. Could the belt be too tight that way?

Greetings
Maurice

============================================================
Logo 700 - Logo 600 - Vbar EVO/Touch
https://www.youtube.com/@mauricekrause
machine-translated from German · Show original
Eddi E. aus G. 1 July 2025 08:5001.07.2025 08:50
Hi Maurice,

The measurement for hanging the belt (with the battery in) is a good guideline. If you were flying very hard and the belt was likely to skip, then increase the measurement accordingly.

I once had an overtightened belt, either because I'd done it myself, or because I'd painted the helicopter... so it wasn't engaging the pulleys properly anymore. It was noisier, and the tail was also unstable. Replaced the belt, and the problem was solved. You'd never guess that.

There have also been some voodoo situations where a different tail section worked wonders, and (for simplicity's sake) the 'suspected' one then worked perfectly on the other helicopter as well. It's also possible that the other helicopter had a different servo; it's been too long.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
maurice.krause 20 July 2025 08:4420.07.2025 08:44
Hi everyone,

@Eddi, I've tried all your points, unfortunately nothing helped, now only the servo is still open...


Is the BLS-905X sufficient?
https://www.kst-servo-shop.de/KST-BLS-905X-V2.0-8kg.cmat8.4V-760us/KST-0912

Or does it have to be the X20-1035?
https://www.kst-servo-shop.de/X20-1035-V3.0-HLS-1.2N.mat8.4-Volt-760us/KST-0432

============================================================
Logo 700 - Logo 600 - Vbar EVO/Touch
https://www.youtube.com/@mauricekrause
machine-translated from German · Show original
Eddi E. aus G. 21 July 2025 08:5121.07.2025 08:51
Good morning,

Phew, I'm afraid I can't say anything about that... who flies these servos and can contribute something?

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
florian_neuner 22 July 2025 10:3622.07.2025 10:36
I just need to chime in briefly:

Regarding the KST servos: I unfortunately don't have a 600, but Valentin flies the 905X.

But I'm not sure if it's actually the servo, since you've already tested your tail servo from the 700 in the 600, right?

Your problem now is that the tail spins out during a pitch climb? Is that correct?

I would start troubleshooting from a different angle.

LG Flo
machine-translated from German · Show original
maurice.krause 22 July 2025 15:4122.07.2025 15:41
Hi Flo,

The rear end no longer swings out; sorry, the update was missing here.

Yes, exactly, I had the servo from my 700 in there, it was a little better, but still...

I also tested the entire rear end of a colleague's car, same behavior.


Problem:

The rear end is oscillating; I've already tested various oscillation suppression values and sensitivities, unfortunately always without success.

Setup reset to a preset has already been performed.

It starts to oscillate extremely during faster maneuvers, such as funnels; the tail recently became uncontrollable, and I haven't flown since, as it was simply too close for comfort.

That's why I asked about the servo; it cost almost 100 euros. Maybe it's the solution, better than trying things out and losing an expensive model.

So what's left then? The servo should arrive in the next few days, I'll test it and give feedback here, but if it's still happening after that, it can only be the VBar, right?

Thank you for your help!

Greetings
Maurice

============================================================
Logo 700 - Logo 600 - Vbar EVO/Touch
https://www.youtube.com/@mauricekrause
machine-translated from German · Show original
Eddi E. aus G. 23 July 2025 09:0523.07.2025 09:05
Hi Maurice,

Maybe a silly question, but then again not so silly :-) ... because I've already seen it: does the tail rotor rotate the right way, or are the tail blades mounted the right way so that they don't run backwards?

Less silly: how stiff is the tail rotor when it's turning? You can test it (very, very carefully!): disconnect the linkage at the tail servo, move it a bit (how easily does it move?), then let the mechanism run, then move the linkage by hand, ... and now?

Another test: Remove the rear hub, pull it axially apart at both blade holders while rotating the hub: is it significantly harder to turn than without pulling?

And, because I've seen it before: does the pushrod hold 100% under tension? There was a pilot once whose ball joints were glued in with a rubbery consistency (wrong mixture of resin and hardener). We spent ages on the phone and writing back and forth, nothing helped, until he brought the helicopter over, I pressed on it a bit, and said, "Look at that... oh!"

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
florian_neuner 23 July 2025 09:5423.07.2025 09:54
If it's actually oscillating and not just shaking, it's often due to stiffness in the mechanism or it could also be the thrust bearings (I had that once on my 700... the thrust bearings were broken and I replaced and tried everything possible, but nothing helped until I replaced the thrust bearings. Back then, it manifested as oscillation that got worse with higher RPMs). Eddi has already given you some great starting points you can check.

But that's precisely the difference: pendulum swing - slow, trembling - fast

Does it also "oscillate" while floating?

If the funnel "oscillates" and "vibrates," that's another sign of electronics. Of course, this also interacts with the mechanics; if something is wrong with the mechanics, the electronics try to compensate. If this doesn't work because the mechanics are jammed or something similar, then suddenly it works, but the control loop has already become so overloaded that it overshoots, and so it goes back and forth.

Which servo did you order?

Do you perhaps have a video of the 600 series so one can get a better idea of what it's like?

LG Flo
machine-translated from German · Show original
maurice.krause 23 July 2025 13:5923.07.2025 13:59
Hi everyone,

Thanks for your replies, I've now ordered the KST BLS905X, I'm going to the airfield later because I wanted to train for the weekend anyway, I'll take the 600 with me, keep your fingers crossed that it's gone now.

Unfortunately, I don't have a video right now, but I'll remember it if I need one later.

@Edi I think if the tail still isn't working, we'll have to talk again about me possibly bringing the helicopter to you or something.

Greetings
Maurice

============================================================
Logo 700 - Logo 600 - Vbar EVO/Touch
https://www.youtube.com/@mauricekrause
machine-translated from German · Show original
maurice.krause 24 July 2025 05:2424.07.2025 05:24
Hi everyone,

The servo was the solution; I didn't have to adjust much yesterday, except for 500Hz/760us, it worked perfectly right away.

Thank you for your help!

Greetings
Maurice Krause

============================================================
Logo 700 - Logo 600 - Vbar EVO/Touch
https://www.youtube.com/@mauricekrause
machine-translated from German · Show original
Eddi E. aus G. 24 July 2025 08:4524.07.2025 08:45
:-) !!!

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless