HP
20 May 2025 19:0720.05.2025 19:07
Hello folks!
I have a few questions about the Logo 480 and its spare parts availability. Most parts are still in stock in the shop, but the blade bearing shaft, for example, is not. Will there be any more parts coming soon?
I'd like to keep flying my 480 for a while longer.
What's the general status of the 480? Will it also be revised, or is it now obsolete?
Hallo Leute!
Habe ein paar Fragen zum Logo 480 wie es da mit der Ersatzteilversorgung aussieht. Das Meiste ist noch im Shop vorhanden, Blattlagerwelle z. B. nicht. Kommt da noch was nach?
Würde meinen 480er schon gerne noch eine Weile fliegen.
Wie sieht es beim 480er generell aus? Wird der auch noch mal überarbeitet oder ist der jetzt Geschichte?
Eddi E. aus G.
21 May 2025 08:5921.05.2025 08:59
Good morning,
It's currently up in the air (hehe :-) )
I've heard that he might come back or stay.
I can ask around about BLW.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
der ist gerade in der Schwebe (hihi :-) )
Ich habe gehört, dass er wieder kommen bzw. bleiben könnte.
Wegen BLW kann ich mich ja mal umhören.
Grüßle
Eddi
Born to fly ...
forced to work.
HP
21 May 2025 19:0821.05.2025 19:08
Hello Eddi!
That sounds good. It would be a real shame to abandon it now, as there's certainly a lot of development work and expense involved.
I'd like to briefly jump in here with a different topic: the wobble effect on the swashplate.
You mentioned in another thread that you can achieve this by increasing the style and decreasing the integral.
I tried it and it actually helped, but it's not perfect yet. Unfortunately, I couldn't test it further due to the weather.
I'm currently using Style at 110 and Integral at 55. How far can I push it before reaching any critical values? Or could it be related to the servos? Savöx 1250. Neo Pro Rescue with the latest update.
Edited once. Last edited on 21.05.2025 at 19:45 by HP.
Hallo Eddi!
Das hört sich erst mal gut an. Wäre echt schade den jetzt auf zu geben, steckt ja sicherlich einiges an Entwicklungsarbeit und Kosten drinn.
Würde hier gern nochmal kurz mit einem anderem Thema rein grätschen, Thema Wobbeleffekt an der Taumelscheibe.
Du hast mal in einem anderem Thread erwähnt mit Style hoch und Integral runter bekommt man das hin.
Hab das ausprobiert und es hat tatsächlich geholfen,ist aber noch nicht perfekt. Leider konnte ich wetterbedingt nicht weiter testen.
Bin jetzt mit Style auf 110 und Integral auf 55. Wie weit kann ich noch gehen bis irgendwelche kritischen Werte erreicht werden? Oder hat es was mit den Servos zu tun. Savöx 1250. Neo pro rescue mit neuestem Update.
1 mal bearbeitet. Zuletzt am 21.05.2025 19:45 von HP.
Eddi E. aus G.
22 May 2025 08:5622.05.2025 08:56
Good morning,
Well, the Savöx 1250s aren't exactly all-purpose weapons :-/
How does the wobbling manifest itself, in which flight conditions, at which RPMs?
What kind of stabilizer bar is installed?
What are the other values?
Style can be pushed to its limits.
Theoretically, yes, although I wouldn't go to 0, as that would eliminate heading hold on the swashplate and also loss consistency in the controls (rotation rate regulation). Before that, it simply decreases; you can certainly experiment with that, but I would always keep a 'safety net' to fall back on if things get tricky.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
naja, die Savöx 1250 sind jetzt nicht unbedingt Allzweckwaffen :-/
Wie äußert sich denn das Wobbeln, in welchen Flugzuständen, bei welchen Drehzahlen?
Was für 'ne Stabi ist da verbaut?
Wie sehen die anderen Werte aus?
Style kann man ausreizen.
I theoretisch auch, wobei ich nicht auf 0 gehen würde, dann hätte man keinen Heading-Hold mehr auf der Taumelscheibe, und im Steuern auch keine Konsistenz (Regelung der Drehrate) mehr. Vorher wird's einfach weniger, kann man schon mit spielen, ich würde nur immer eine 'sichere Bank' behalten, in die ich zurück schalten kann, wenn's haarig wird.
Grüßle
Eddi
Born to fly ...
forced to work.
HP
22 May 2025 11:3022.05.2025 11:30
Hello Eddi!
Stabi is a NEO pro rescue, control VBar control touch with the latest updates installed.
The wobbling is only visible when hovering; it's practically invisible in flight.
The tail boom moves about half a centimeter up and down, i.e., via pitch, but you can also see it via roll.
Just a wobbling motion with a (let's call it a repetition rate) of about 1-2 times per second.
Engine speeds are 2100-2200-2300, almost nothing at bank 3, but still clearly recognizable at bank 1.
Style 110
Sensitivity 70
Integral 55
All other values are set to default on all banks.
Hallo Eddi!
Stabi ist ein NEO pro rescue, Steuerung V-Bar control touch mit den neuesten Updates drauf.
Das wobbeln sieht man nur beim Schweben, im Flug eigentlich nichts erkennbar.
Der Heckausleger bewegt sich ca. nen halben cm nach oben und unten, also über Nick, man sieht es aber auch über Roll.
Eben eine Taumelbewegung mit einer (ich nennen es mal Wiederholrate) von ca. 1-2 mal pro Sek.
Drehzahlen sind 2100-2200-2300, bei Bank 3 jetzt fast nichts mehr, bei Bank 1 doch noch deutlich zuerkennen.
Style 110
Empfindlichkeit 70
Integral 55
Alle anderen Werte auf Standard, auf allen Bänken.
Bernhard Kerscher
23 May 2025 08:5723.05.2025 08:57
Hello HP,
In my experience, the head damping of the 480xx is a bit too harsh.
Especially suitable for low speeds and light blades.
That's why wobbling will be easier for you at high speed.
How did you set up your head, with 1mm washers or 0.5mm washers?
8x11x0.5 (soft dampening)
8x11x1 (hard dampening)
You can also wait and fly for a while; perhaps the rubbers will soften and the wobbling will disappear on its own.
Greetings Bernhard
Edited twice. Last edited on 23.05.2025 at 09:08 by Bernhard Kerscher.
Hallo HP,
meiner Erfahrung nach ist die Kopfdämpfung des 480xx etwas zu hart.
Vor allem für niedrige Drehzahlen und leichten Blättern.
Deshalb wird das Wobbeln bei dir leichter mit hoher Drehzahl.
Wie hast du deinen Kopf aufgebaut mit 1mm Washer oder 0.5mm?
8x11x0,5 (soft dampening)
8x11x1 (hard dampening)
Du kannst auch erst mal warten und fliegen, vielleicht werden die Gummis noch weicher und das Wobbeln verschwindet von selber.
Grüße Bernhard
2 mal bearbeitet. Zuletzt am 23.05.2025 09:08 von Bernhard Kerscher.
Eddi E. aus G.
23 May 2025 09:2623.05.2025 09:26
Good morning,
That's a good idea too :-)
I would also try weighing the main rotor blades, or, more simply, placing a strip of insulating tape at the center of gravity on one blade and seeing if it improves or worsens.
And if you have them, try different tail rotor blades, or weigh them as well.
I used to have something similar (tail boom up-down), rigid, without stabilization.
I fitted different tail fins almost by accident, changed nothing else, and bam, it was gone.
You can also experiment with the center of gravity; just shift the battery slightly, if in doubt, lean it slightly forward.
Ultimately, it's about making the job a little easier, especially for 'normal' servos.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
auch ein guter Gedanke :-)
Ich würde aber auch mal die Hauptrotorblätter auswiegen, oder hemdsärmelig, einen Streifen Isolierband etwa in den Schwerpunkt, an einem Blatt, schauen ob's besser oder schlechter wird.
Und wenn Du hast probiere mal andere Heckrotorblätter, oder wiege die auch mal aus.
Hatte früher mal was vergleichbares (Heckausleger rauf-runter), Rigid noch ohne Stabilisierung.
Mehr durch Zufall habe ich andere Heckblätter montiert, sonst nix verändert, zack, war weg.
Kannst auch mit dem Schwerpunkt experimentieren, einfach mal den Akku etwas verschieben, im Zweifel eher etwas vorlastig.
Am Ende geht's drum, gerade 'normaleren' Servos die Arbeit etwas zu erleichtern.
Grüßle
Eddi
Born to fly ...
forced to work.
HP
23 May 2025 19:2123.05.2025 19:21
Hello!
I bought the helicopter used and took the rotor head apart to lubricate the O-rings and the blade shaft, but I didn't check whether it had 0.5mm or 1mm shims. That would be another possibility, of course.
I will keep you updated on how things have been going as soon as the weather improves.
The main and tail rotor blades are from RT, as they come in the kit.
It'll be fine, my 550 SE flies perfectly after all, without any problems.
Greetings to everyone and thank you for the answers.
Hallo!
Hab den Heli gebraucht übernommen, hatte den Rotorkopf auch auseinander um die O-Ringe und die Blattlagerwelle zu schmieren, hab aber nicht drauf geachtet ob die 0,5 oder die 1mm Paßscheiben verbaut sind. wär natürlich auch noch eine Möglichkeit.
Werde euch weiter berichten wie es mir ergangen ist sobald das Wetter wieder besser ist.
Haupt und Heckrotorblätter sind von RT, so wie sie im Baukasten dabei sind.
Wird schon werden, mein 550 SE fliegt schließlich auch perfekt, ohne Probleme.
Grüße an alle und danke für die Antworten.
HP
21 October 2025 18:4821.10.2025 18:48
Hello folks!
It took quite a while, but I wanted to give you a quick update on how the story turned out.
In short: The 480 flies great now, the wobbling is gone!
I disassembled the rotor head a few more times and tested it with various damping configurations.
The final version has a 1mm shim inside with ground-down O-rings, just like in Rainer's video Low RPM Dampening.
Now it flies perfectly!
However, I have another question regarding the assembly instructions, specifically whether I've interpreted them correctly. I see a 1mm and a 0.5mm shim being used. I tried it that way, but the blade grips were quite stiff and it wasn't flyable. Severe wobbling and significant oscillations after cyclic control inputs were the result.
I also tried using only a 0.5mm shim, but then the blade holders were stiff, probably because 0.5mm is too little clearance between the O-ring and the inner blade holder bearing. I think the O-ring then touches the outer race of the blade holder bearing.
Hallo Leute!
Hat jetzt doch eine Zeit lang gedauert, wollte mich aber noch mal kurz melden wie die Geschichte ausgegangen ist.
Kurz und knapp: Der 480er fliegt jetzt super, das wobbeln ist weg!
Habe den Rotorkopf noch (ein paar) mal auseinander gebaut und mit verschiedensten Dämpfungskonfigurationen getestet.
Letztstand ist eine Paßscheibe drinnen mit 1mm und abgeschliffenen O-Ringen so wie in Rainers Video Low RPM Dampening.
So fliegt er jetzt perfekt!
Allerdings hab ich noch eine Frage zur Bauanleitung, ob ich die richtig interpretiert habe. Ich sehe da eine 1mm und eine 0,5mm Paßscheibe verbaut. Hab das auch so probiert, aber damit waren die Blatthalter ziemlich schwergängig und ließ sich so auch nicht vernünftig fliegen. Starkes Wobbeln und starkes Nachschwingen nach zyklischen Steuereingaben waren die Folge.
Hab auch probiert nur eine 0,5mm Paßscheibe, aber da waren die Blatthalter dann auch schwergängig, wahrscheinlich weil 0,5 zu wenig Abstand zwischen O-Ring und innerem Blatthalterlager ist. Denke das sich dann der O-Ring mit dem Aussenring vom Blatthalterlager berührt.
Eddi E. aus G.
22 October 2025 08:5522.10.2025 08:55
Good morning,
In my opinion, it depends on what you use it for, what RPMs you fly, and whether the head should be tuned harder or softer.
"Smoke is difficult" is relative.
And the forces have to be absorbed somehow, so that nothing comes loose or tilts.
The servos must also be able to handle/cope with this.
For most people, I think it works as described in the instructions, but it's also not wrong to try, for example, with 1 mm, or with different rubbers, or to sand down the rubbers, and it may also change over time as everything breaks in, settles, and with the aging of the rubbers.
The main thing is that the helicopter flies great (now) :-) I'm happy!
—Eddi
Born to fly ...
forced to work.
Moin,
mMn kommt's drauf an, was man damit macht, was man für Drehzahlen fliegt, ob der Kopf besser härter oder weicher abgestimmt sein mag.
Schwergängig ist rauch relativ.
Und die Kräfte müssen irgendwie aufgenommen werden, so dass nix angeht oder aufkantet.
Die Servos müssen damit dann auch umgehen/können.
Für die meisten denke ich funktioniert es wie in der Anleitung beschrieben, aber es ist auch nicht falsch, bspw. mit 1 mm zu probieren, oder mit anderen Gummis, oder die Gummis abzuschleifen, und es verändert sich ggfs. auch über die Zeit, wenn sich alles etwas einläuft, setzt, und mit der Alterung der Gummis.
Hauptsache ist doch, dass der Heli dann (jetzt) super fliegt :-) freut mich!
—Eddi
Born to fly ...
forced to work.