Wingtip
10 April 2025 07:2110.04.2025 07:21
Hi everyone,
I'd like to measure the pitch values of my L200. (After rebuilding it, as it was recently encased in concrete)
There is nothing to be found in the (online) instructions.
The only guide is the length of the rods and the marking on the central piece and plate holder.
Logically, I'm assuming 0 degrees.
Now the question is, what max/min pitch values does the L200 need? So that I can properly set the 8 degrees again.
Thank you in advance.
Tach zusammen,
ich würde gerne meinen L200 mal durchmessen bezüglich der Pitchwerte. (Nach Wiederaufbau, da kürzlich einbetoniert)
In der (online-) Anleitung ist nichts zu finden.
Einzige Orientierung ist die Länge der Gestänge und die Markierung am Zentralstück und Platthalter.
Da gehe ich logisch von 0 Grad aus.
Nun die Frage, was brauch der L200 als Max/Min Pitch Werte ? Damit ich auch die 8 Grad wieder sauber einstellen kann.
Danke vorab
Eddi E. aus G.
10 April 2025 08:5810.04.2025 08:58
Good morning,
Please just do the basic setup for the LOGO 200, trim the swashplate, pitch to 0° (fold the blades, at 0° the tips touch), do a trim flight, and you're done.
That'll do.
If you had a sufficiently accurate and suitable pitch gauge (or calculated angles), you would arrive at an unusually low pitch of, I believe, 11°... but that's enough, obviously ^^
Don't overthink it, go fly ;-)
—Eddi
Born to fly ...
forced to work.
Moin,
bitte mach einfach das Grundsetup für den LOGO 200, trimme die Taumelscheibe, Pitch auf 0° (Blätter anklappen, bei 0° berühren sich die Spitzen), mache einen Trimmflug, fertig.
Das passt dann schon.
Wenn Du eine ausreichend genaue und passende Pitchlehre hättest (oder Winkel rechnen würdest), würdest Du auf ungewöhnlich geringe glaube ich 11° Pitch kommen ... das reicht aber auch, offensichtlich ^^
Mach keine Wissenschaft draus, geh fliegen ;-)
—Eddi
Born to fly ...
forced to work.
Wingtip
10 April 2025 14:4110.04.2025 14:41
I went flying... afterwards it was broken :-/
And only because the little "shitty brat" spontaneously turns his backside away every now and then.
I hope the uncontrolled rear-end breakaway in reverse maneuvers will be improved with the Evo Micro and V8.
I'm looking forward to the upgrade as soon as it's available.
Then I'll do it as described.
11 degrees doesn't sound like much, but consider that the little one has a head temperature of almost 5800mm.
Ich war fliegen ... danach war er kaputt :-/
Und nur weil der kleine "Scheißer" immer mal wieder spontan den Hintern weg dreht.
Hoffe das unkontrollierte ausbrechen vom Heck in Rückwärtsfiguren wird mit der Evo Micro und V8 besser.
Ich freue mich schon auf das Upgrade sobald verfügbar.
Dann mach ich das mal wie beschrieben.
11 Grad hören sich nicht viel an aber man bedenke der Krümel hat knapp 5800am Kopf.
Eddi E. aus G.
10 April 2025 15:0410.04.2025 15:04
Hi,
Yes, that's sometimes the order I go in too :duckundwech: :-)
Sorry.
When performing backward figures, you simply have to keep the pull on the rotor... once it's unloaded in an unfavorable way, and 'whoosh'.
Easier said than done :-)
My backwards experience with a 600 SX a while back was, yay, it works, it looks great... where did that tree suddenly come from?!
The rear end will definitely look even better with a V8 :-)
Grüßle
Eddi
Born to fly ...
forced to work.
Huhu,
ja in der Reihenfolge ist's bei mir auch gelegentlich :duckundwech: :-)
Sorry.
Bei Rückwärtsfiguren 'muss man einfach' Zug auf dem Rotor behalten ... einmal ungünstig entlastet, und 'schwups'.
Leicht dahin gesagt :-)
Mein Rücken-Rückwärts-Erlebnis mit einem 600 SX vor längerem war, yay, geht, sieht toll aus ... wo kam auf einmal der Baum her?!
Das Heck wird mit V8 auf jeden Fall nochmal besser :-)
Grüßle
Eddi
Born to fly ...
forced to work.
Wingtip
15 April 2025 18:0715.04.2025 18:07
So, I have to get in touch again, because...
Fly modestly.
-Everything rebuilt as needed, including the HRW and BLW.
- New setup loaded and TS adjusted accordingly.
- Leaves folded -> Zero pitch checked / adjusted.
- Trim flight performed
How? Manually initiated in the VBar and trim flight performed in Bank 3.
I hope I finished it correctly, because the pirouettes around the vertical axis look almost good.
But it still spins out completely during flips over pitch. The tail is so unpredictable that it's no fun at all.
Feels soft, oscillates in the 3rd bank and the stops in both directions are watered down.
I replaced the rear propeller with a new one after the crash. The tail boom and the small aluminum plate are also new.
I'm now a bit lost and would like to start tweaking the parameters of the standard setup.
Out of desperation during today's flight, I added pendulum suppression up to 25%.
It didn't bring any improvement, so I took it out again.
What now ?
Greetings Frank
Edited once. Last edited on 15.04.2025 at 18:09 by Wingtip.
Soo- muss mich nochmal melden, denn....
Fliegt bescheiden.
-Alles soweit nötig neu aufgebaut inkl der HRW und BLW.
- Neues Setup geladen und die TS passend getrimmt.
- Blätter an geklappt -> Null Pitch kontrolliert / justiert.
- Trimmflug gemacht
Wie ? In der VBar manuell angestoßen und in Bank 3 Trimmflug durchgeführt.
Hoffe ich habe den richtig abgeschlossen, den die Pirouetten um die Hochachse sehen fast gut aus.
Aber dennoch dreht er völlig raus beim Flip über Nick. Das Heck ist so das es keinen Spaß macht.
Fühlt sich weich an, Pendelt in der 3. Bank und die Stopps in beide Richtungen sind verwässert.
Heck Prop hab ich nach dem Einschlag gegen einen neuen getauscht. Auch Heckrohr und die kleine AluPlatte sind frisch
Bin nun etwas Ratlos und würde jetzt anfangen an den Parametern vom Standard Setup zu schrauben.
Aus Verzweiflung beim letzten Flug heute mal Pendelunterdrückung mit bis zu 25 reingenommen.
Brachte keine Verbesserung also wieder raus damit.
Was nun ?
Grüße Frank
1 mal bearbeitet. Zuletzt am 15.04.2025 18:09 von Wingtip.
Eddi E. aus G.
16 April 2025 08:5416.04.2025 08:54
Hi Frank,
Check if the rear prop is on the right way round ;-)
If the setup was no good, everyone would fly terribly...
Did you only set/check trim and 0-pitch in the setup?
Because... outside of the setup the control loop is active, including lightness (changes pitch even statically, on the ground).
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Frank,
schau mal, ob der Heck-Prop richtig rum drauf ist ;-)
Wenn das Setup nix wäre, würden alle mistig fliegen ...
Trimmung und 0-Pitch hast Du nur im Setup eingestellt/kontrolliert?
Weil ... außerhalb vom Setup ist der Regelkreis aktiv, auch Leichtigkeit (verändert Pitch auch statisch, am Boden).
Grüßle
Eddi
Born to fly ...
forced to work.
Wingtip
16 April 2025 09:1516.04.2025 09:15
Hi Eddi,
Yes, I refrained from mentioning the classic example of the prop being mounted backwards at the rear. It's fine ;-)
Trim and 0 Pitch are only ever used in the setup, where the pitch stick shows no reaction.
First, in the window with the individual servo trims, adjust the levers to "center".
Then, in the overall window, use the Pitch "up/down" controls to adjust the zero pitch.
I'll take another look after breakfast...
Moin Eddi,
ja den Klassiker das der Prop am Heck falsch rum montiert ist, hab ich mir verkniffen. Der passt ;-)
Trimmung und 0 Pitch immer nur im Setup, da wo der Pitch Knüppel keine Reaktion zeigt.
Also zunächst im Fenster mit den Einzeltrimmungen der Servos zur Einstellung der Hebel auf "Mitte"
Dann im übergreifenden Fenster Pitch "auf/ab" um die Null Pitch anzupassen.
Ich schau nach dem Frühstück nochmal drüber...