Christoph68
25 February 2026 18:3925.02.2026 18:39
Hello dear Mikado community,
I have a question about my Logo 200: what are the dimensions of the two screws that secure the main rotor shaft in the motor area? I mean the small setscrew that is screwed in from the side, and the screw at the bottom end of the main rotor shaft.
Thank you very much and best regards
Christoph
Hallo liebe Mikado-Community,
ich habe eine Frage zu meinem Logo 200: welche Maße haben die beiden Schrauben, die im Bereich des Motors die Hauptrotorwelle sichern? Also ich meine die kleine Madenschraube, die seitlich eingeschraubt ist sowie die Schraube am unteren Ende der Hauptrotorwelle.
Herzlichen Dank und lieben Gruß
Christoph
Eddi E. aus G.
26 February 2026 09:0526.02.2026 09:05
Good morning,
the Made M3 x 2.5
The screw at the bottom is M2.5 x 4
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
die Made M3 x 2,5
Die Schraube unten M2,5 x 4
Grüßle
Eddi
Born to fly ...
forced to work.
Christoph68
26 February 2026 19:1326.02.2026 19:13
Good evening Eddi,
Thank you so much for your quick reply. I was a bit puzzled about which Allen key was the right one for both screws, in case I ever find myself in the position (and I'm sure I will) of having to replace the shaft. The wrench size seems to be the same for both screws. At least a 1.5mm hex key seems to fit both of them reasonably well. The soldering iron will take care of the rest. I initially thought the lower one was a Torx screw.
greeting
Christoph
Guten Abend Eddi,
herzlichen Dank für Deine rasche Antwort. Ich war ein bisschen am Rätseln, welches der richtige Innensechskantschlüssel für beide Schrauben ist, falls ich mal in die Verlegenheit komme (und die kommt bestimmt), die Welle wechseln zu müssen. Die Schlüsselweite scheint bei beiden Schrauben gleich zu sein. Zumindest scheint bei mir ein 1,5mm Sechskant bei beiden Schrauben einigermaßen zu passen. Den Rest macht dann der Lötkolben. Ich dachte erst, die untere wäre eine Torx-Schraube.
Gruß
Christoph
Bernd S.
27 February 2026 05:4627.02.2026 05:46
Good morning,
So far I've only "picked out" tools for the leaf holders ( @Admins - not changed 8-) )
The dimensions are also somewhat unclear, and the tools have some play, even though I already obtained the precise tools that were originally for the Chinese helicopter from Staufenbiel (whose screws had a hardness similar to lead).
I wanted to take another look at it with a magnifying lens anyway to see exactly what's there (over 50).
Messing up tiny screws doesn't make life any easier :-) .
It's probably a good idea to keep spare screws in your archives (every helicopter will eventually be unintentionally "put down").
The weather will be good this weekend - time to fly the helicopters!
Bernd
Moin,
ich habe bisher nur Werkzeug für die Blatthalter "rausgesucht" ( @Admins - nicht verändert 8-) )
Auch da sind die Maße etwas unklar bzw. sind die Werkzeuge mit etwas Luft obwohl ich schon die präzisen Werkzeuge die damals für den Chinaheli von Staufenbiel( dessen Schrauben eine Härte ähnlich Blei hatten ) besorgte.
Ich wollte mir das eh noch mal mit Lupenobjektiv anschauen was da genau ist ( ü50 ).
Winzschrauben zu vergurken macht das Leben ja nicht leichter :-) .
Ersatzschrauben sollte man wohl sich ins Archiv legen ( irgendwann wird wohl jeder Heli mal ungewollt "abgelegt" )
Wochenende gibts gutes Wetter - Helis ausführen !
Bernd
Eddi E. aus G.
27 February 2026 09:1527.02.2026 09:15
Good morning,
1.5 mm fits.
I have an ancient set of socket wrenches from the car sector, with really sharp blades; I've rarely stripped screw heads or grubs with them.
If the key wobbles noticeably in the screw head or the grub screw, ... be careful.
Torx can help with stripped screws, but ultimately only once... or not at all.
A soldering iron is a good idea, also (carefully) for the servo arm screws.
OMP is generous with screw locking (they do some of the pre-assembly, and the servos come with the arm attached (better than having the arm broken off...).
That's generally better than screws deserting, but with those fiddly little wires with coiled threads (that's all they are, like the show with the mouse...) you don't need much force to unscrew them.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
1,5 mm passt.
Ich habe ein uraltes Set Steckschlüssel aus dem Car-Bereich, mit richtig scharfen Klingen, damit habe ich noch selten Schraubenköpfe oder Maden ausgenudelt.
Wenn der Schlüssel deutlich wackelt im Schraubenkopf oder in der Made, ... Vorsicht.
Torx kann bei ausgenudelten Schrauben helfen, aber am Ende auch nur einmal ... oder nicht.
Lötkolben ist 'ne gute Idee, auch (vorsichtig) für die Servoarm-Schrauben.
OMP meint es gut mit Schraubensicherung (die machen die Vormontage tws., und die Servos kommen auch mit Arm dran (besser als Arm ab ...).
Das ist auch grundsätzlich besser, als dass Schrauben Fahnenflucht begehen, aber bei den fipseligen Drähtchen mit aufgerolltem Gewinde (was anderes isses ja nicht, Sendung mit der Maus ...) braucht's auch nicht viel Kraft, die abzudrehen.
Grüßle
Eddi
Born to fly ...
forced to work.
Bernd S.
27 February 2026 12:0727.02.2026 12:07
Confirmation that the screws are precise - I just had a minor mishap and needed an Allen key at the airfield.
My regular tool kit included a "professional" Allen key that fits most (all) of the L200's screws.
He was immediately recruited into the L200 case.
(Because - as Eddi already wrote - botched = over).
Mishap occurred with the Multiplex ProfiTX DeJaVue – the transmitter strap came unhooked during takeoff – the helicopter crashed onto the launch area (cardboard on the grass) just as the wind lifted it (I was a bit careless) – it broke one skid -> glued the skids – I need a replacement – I might have to order something. And that's why I needed the Allen wrench today.
The carabiner is now secured to the belt.
Incidentally, at 5000 RPM the L200 is a rocket when needed :-) .
And today I flew 4 batteries outside in windy conditions at 3400 RPM - 9:40 min with 30% battery remaining.
Edit: 3000 RPM also seems to work - test Sunday indoors.
Greetings Bernd
Edited once. Last edited on 27.02.2026 at 12:29 by Bernd S.
Bestätigung, die Schrauben sind präzise - hatte gerade kleines Malheur und brauchte auf dem Flugplatz nen Innensechskant.
In meinem normalen Werkzeug war "Profi"Innensechskant der absolut zu den meisten ( allen ) Schrauben des L200 passt.
Der wurde gleich in den L200 Koffer rekrutiert.
( Weil - wie Eddi schon schrieb - vergurkt = vorbei ).
Malheur war Multiplex ProfiTX DeJaVue - der Sendergurt hakte aus beim Start - Heli klatschte auf Startfläche ( Pappe auf dem Rasen ) wie auch der Wind grad hochhob ( ich war etwas unbedacht ) - killte eine Kufe -> Kufen geklebt - brauche Ersatz - evt. muss ich da was ordern . Und da brauchte ich heute schon eben den Innensechkant.
Karabiner vom Gurt nun gesichert.
Nebebei - mit 5000U/Min ist der L200 ja ne Rakete bei Bedarf :-) .
Und ich flog heute 4 Akkus bei Wind draußen mit 3400U/Min - 9:40Min mit 30% Rest im Akku.
Edit: 3000UMin scheinen auch zu gehen - Test Sonntag indoor.
Grüße Bernd
1 mal bearbeitet. Zuletzt am 27.02.2026 12:29 von Bernd S..
Eddi E. aus G.
27 February 2026 13:1827.02.2026 13:18
Good morning,
Well, I first had that déjà vu with Graupner... loooong time ago.
Carabiner without a safety catch, twisted at an awkward angle, gravity...
Funny, since I've been flying with a handheld transmitter and without suspenders, it doesn't happen anymore :-)
—Eddi
Born to fly ...
forced to work.
Moin,
naja, das Déjà Vu hatte ich das erste Mal bei Graupner ... loooong time ago.
Karabiner ohne Sicherung, ungünstig verdreht, Gravitation ...
Komisch, seit ich Handsender fliege und ohne Hosenträger, nicht mehr :-)
—Eddi
Born to fly ...
forced to work.