I have a Logo 200 2025 V8.
The maximum pitch is too low for me in the default setting.
However, I didn't want to simply adjust the pitch curve, but rather checked the basic settings.
I noticed that the cyclic calibration is set to 84% and the corresponding pitch value is slightly over 4 degrees, far from the 8 degrees. This would actually be incorrect and an indication of mechanical "defects".
I then increased the value to 150% (that's the maximum value in the calibration). The pitch value then rises to over 6 degrees, but you can't get to 8 degrees that way.
The maximum pitch value is higher after the recalibration, but still not high enough.
I then adjusted the rest to the 11 degrees I wanted using the pitch curve.
The following questions are related:
What effect does a precise setting of 8 degrees have?
Does this affect any control parameters?
What is the correct procedure if you cannot set the 8 degrees, as with the Logo 200 2025 V8?
- only set the maximum pitch value via the pitch curve and do not change the factory calibration or
- Calibrate as high as possible and adjust the rest via the pitch curve?
Thanks
The maximum pitch is too low for me in the default setting.
However, I didn't want to simply adjust the pitch curve, but rather checked the basic settings.
I noticed that the cyclic calibration is set to 84% and the corresponding pitch value is slightly over 4 degrees, far from the 8 degrees. This would actually be incorrect and an indication of mechanical "defects".
I then increased the value to 150% (that's the maximum value in the calibration). The pitch value then rises to over 6 degrees, but you can't get to 8 degrees that way.
The maximum pitch value is higher after the recalibration, but still not high enough.
I then adjusted the rest to the 11 degrees I wanted using the pitch curve.
The following questions are related:
What effect does a precise setting of 8 degrees have?
Does this affect any control parameters?
What is the correct procedure if you cannot set the 8 degrees, as with the Logo 200 2025 V8?
- only set the maximum pitch value via the pitch curve and do not change the factory calibration or
- Calibrate as high as possible and adjust the rest via the pitch curve?
Thanks
Habe einen Logo 200 2025 V8.
In der Standardeinstellung ist mir der max. Pitch zu gering.
Ich wollte aber nicht einfach die Pitchkurve verstellen sondern habe die Grundeinstellungen überprüft.
Dabei ist mir aufgefallen, dass die zykliche Kalibrierung bei 84% steht und der dazugehörige Pitchwert bei etwas mehr als 4 Grad, also weit weg von den 8 Grad. Das wäre ja eigentlich falsch und ein Hinweis auf mechanische "Defizite".
Habe dann den Wert auf 150% hochgedreht (das ist der Maximalwert in der Kalibrierung). Der Pitchwert steigt dabei auf über 6 Grad, aber auf 8 Grad kommt man so nicht.
Der maximale Pitchwert ist nach der veränderten Kalibirierung höher aber noch nicht hoch genug.
Den Rest auf die 11 Grad, die ich möchte, habe ich dann über die Pitchkurve eingestellt.
Dazu folgende Fragen:
Was bewirkt eine genaue Einstellung auf 8 Grad?
Hat das Einfluss auf irgendwelche Regelparameter?
Was ist das korrekte Vorgehen, wenn man die 8 Grad nicht einstellen kann, wie beim Logo 200 2025 V8
- den maximalen Pitchwert nur über die Pitchkurve einstellen und die Werkskalibrierung nicht verändern oder
- die Kalibirierung so hoch wie möglich und den Rest über die Pitchkurve?
Danke
In der Standardeinstellung ist mir der max. Pitch zu gering.
Ich wollte aber nicht einfach die Pitchkurve verstellen sondern habe die Grundeinstellungen überprüft.
Dabei ist mir aufgefallen, dass die zykliche Kalibrierung bei 84% steht und der dazugehörige Pitchwert bei etwas mehr als 4 Grad, also weit weg von den 8 Grad. Das wäre ja eigentlich falsch und ein Hinweis auf mechanische "Defizite".
Habe dann den Wert auf 150% hochgedreht (das ist der Maximalwert in der Kalibrierung). Der Pitchwert steigt dabei auf über 6 Grad, aber auf 8 Grad kommt man so nicht.
Der maximale Pitchwert ist nach der veränderten Kalibirierung höher aber noch nicht hoch genug.
Den Rest auf die 11 Grad, die ich möchte, habe ich dann über die Pitchkurve eingestellt.
Dazu folgende Fragen:
Was bewirkt eine genaue Einstellung auf 8 Grad?
Hat das Einfluss auf irgendwelche Regelparameter?
Was ist das korrekte Vorgehen, wenn man die 8 Grad nicht einstellen kann, wie beim Logo 200 2025 V8
- den maximalen Pitchwert nur über die Pitchkurve einstellen und die Werkskalibrierung nicht verändern oder
- die Kalibirierung so hoch wie möglich und den Rest über die Pitchkurve?
Danke
machine-translated from German · Show original