Good day,
I have a small, but big problem with my Logo 200. On Monday, the tail failed during flight; I had almost no control over it and landed the little plane in, thankfully, tall grass. Shortly before, I heard an unusual humming noise from (presumably) the tail motor, but I wasn't able to get down quickly enough, and while attempting to turn for landing, the tail failed.
No major damage to the helicopter; the tail boom is straight, as is the main rotor shaft; nothing is visible on the head. The tail fin is cracked, the metal bracket for the tail motor is slightly bent, one main rotor blade is slightly bent, and one skid is slightly cracked.
I replaced all the damaged parts (thanks again for the super fast shipping).
I ran the helicopter on the bench without the blades. I double-checked that the main rotor shaft was perfectly straight. Everything seems fine here; no vibrations. The unusual humming from the tail motor was also gone.
The problems arose during the test flight. During spool-up, the message "Extreme Vibration Level" appeared intermittently. Everything seemed normal in hover, but during quick stops from a turn, the tail swung excessively, especially to the left. To the right, it seemed to turn very slowly, as if the motor wasn't reaching sufficient RPM. This oscillation occurred on all banks (at standard RPMs). Additionally, the message "High Vibration Level" appeared, which I had never seen before. The highest vibration level was 2600.
The last flight before the crash was about 30 minutes prior, and everything was fine then. I don't fly 3D; I just fly my usual relaxed to sporty circuits.
I found older posts about a burnt-out rear engine, but it doesn't smell burnt, there's nothing to see visually, and it never got stuck anywhere.
I would still suspect the motor and the vibrations caused by the strong oscillations. Could it be something with the speed controller after all?
I bought the good one in September 2023.
Best regards,
Jan
I have a small, but big problem with my Logo 200. On Monday, the tail failed during flight; I had almost no control over it and landed the little plane in, thankfully, tall grass. Shortly before, I heard an unusual humming noise from (presumably) the tail motor, but I wasn't able to get down quickly enough, and while attempting to turn for landing, the tail failed.
No major damage to the helicopter; the tail boom is straight, as is the main rotor shaft; nothing is visible on the head. The tail fin is cracked, the metal bracket for the tail motor is slightly bent, one main rotor blade is slightly bent, and one skid is slightly cracked.
I replaced all the damaged parts (thanks again for the super fast shipping).
I ran the helicopter on the bench without the blades. I double-checked that the main rotor shaft was perfectly straight. Everything seems fine here; no vibrations. The unusual humming from the tail motor was also gone.
The problems arose during the test flight. During spool-up, the message "Extreme Vibration Level" appeared intermittently. Everything seemed normal in hover, but during quick stops from a turn, the tail swung excessively, especially to the left. To the right, it seemed to turn very slowly, as if the motor wasn't reaching sufficient RPM. This oscillation occurred on all banks (at standard RPMs). Additionally, the message "High Vibration Level" appeared, which I had never seen before. The highest vibration level was 2600.
The last flight before the crash was about 30 minutes prior, and everything was fine then. I don't fly 3D; I just fly my usual relaxed to sporty circuits.
I found older posts about a burnt-out rear engine, but it doesn't smell burnt, there's nothing to see visually, and it never got stuck anywhere.
I would still suspect the motor and the vibrations caused by the strong oscillations. Could it be something with the speed controller after all?
I bought the good one in September 2023.
Best regards,
Jan
Guten Tag,
Ich habe ein kleines, großes Problem mit meinem Logo 200. Am Montag hat während des Flugs das Heck versagt, sprich hatte kaum noch Kontrolle über das Heck und habe den Kleinen ins , zum Glück, hohe Gras gesetzt. Kurz vorher habe ich noch ein ungewöhnliches Summen vom (vermutlich) Heckmotor gehört, so schnell war ich dann aber nicht unten und beim Versuch fürs Landen zu wenden, hat das Heck versagt.
Keine größeren Schäden am Heli, Heckrohr ist gerade, Hauptrotorwelle auch, am Kopf nix zu sehen. Heckfinne angebrochen und der Metalhalter vom Heckmotor leicht verbogen, ein Hauptrotorblatt leicht verbogen, eine Kufe leicht angeknackst.
Beschädigten Teile habe ich alle getauscht (hier nochmal danke für den super schnellen Versand).
Heli auf der Bank ohne Blätter laufen lassen. Nochmal vergewissert, dass die Hauptrotorwelle wirklich gerade ist. Hier scheint alles gut, keine Vibrationsmeldungen. Das ungewöhnliche Summen vom Heckmotor war auch weg.
Beim Testflug nun aber die Probleme. Beim Spool Up immer einmal die Meldung "Extreme Vibration Level". Im Hover scheint erstmal alles normal, aber bei schnellen Stops aus der Drehung schwinkt das Heck extrem nach, gerade links herum. Rechts rum dreht er dafür gefühlt sehr langsam, als würde der Motor nicht genug Drehzahl schaffen. Das Nachschwingen ist auf allen Bänken (Standard Drehzahlen). Dazu gibt es dann auch die Meldung "High Vibration Level", hatte ich vorher nie. Höchstes Vibrationslevel 2600.
Der letzte Flug vor dem Crash war ca. 30 min vorher, da war alles gut. Fliege kein 3D sondern entspannt bis sportlich meine Runden.
Hatte ältere Beiträge mit abgerauchtem Heckmotor gefunden, aber der riecht nicht verbrannt, optisch auch nix zu sehen, hängen geblieben ist er auch nie irgendwo.
Würde bis jetzt trotzdem auf den Motor tippen und die Vibrationen durchs starke Nachschwingen? Kann es doch was am Regler sein?
Gekauft habe ich den Guten im September 23.
Viele Grüße,
Jan
Ich habe ein kleines, großes Problem mit meinem Logo 200. Am Montag hat während des Flugs das Heck versagt, sprich hatte kaum noch Kontrolle über das Heck und habe den Kleinen ins , zum Glück, hohe Gras gesetzt. Kurz vorher habe ich noch ein ungewöhnliches Summen vom (vermutlich) Heckmotor gehört, so schnell war ich dann aber nicht unten und beim Versuch fürs Landen zu wenden, hat das Heck versagt.
Keine größeren Schäden am Heli, Heckrohr ist gerade, Hauptrotorwelle auch, am Kopf nix zu sehen. Heckfinne angebrochen und der Metalhalter vom Heckmotor leicht verbogen, ein Hauptrotorblatt leicht verbogen, eine Kufe leicht angeknackst.
Beschädigten Teile habe ich alle getauscht (hier nochmal danke für den super schnellen Versand).
Heli auf der Bank ohne Blätter laufen lassen. Nochmal vergewissert, dass die Hauptrotorwelle wirklich gerade ist. Hier scheint alles gut, keine Vibrationsmeldungen. Das ungewöhnliche Summen vom Heckmotor war auch weg.
Beim Testflug nun aber die Probleme. Beim Spool Up immer einmal die Meldung "Extreme Vibration Level". Im Hover scheint erstmal alles normal, aber bei schnellen Stops aus der Drehung schwinkt das Heck extrem nach, gerade links herum. Rechts rum dreht er dafür gefühlt sehr langsam, als würde der Motor nicht genug Drehzahl schaffen. Das Nachschwingen ist auf allen Bänken (Standard Drehzahlen). Dazu gibt es dann auch die Meldung "High Vibration Level", hatte ich vorher nie. Höchstes Vibrationslevel 2600.
Der letzte Flug vor dem Crash war ca. 30 min vorher, da war alles gut. Fliege kein 3D sondern entspannt bis sportlich meine Runden.
Hatte ältere Beiträge mit abgerauchtem Heckmotor gefunden, aber der riecht nicht verbrannt, optisch auch nix zu sehen, hängen geblieben ist er auch nie irgendwo.
Würde bis jetzt trotzdem auf den Motor tippen und die Vibrationen durchs starke Nachschwingen? Kann es doch was am Regler sein?
Gekauft habe ich den Guten im September 23.
Viele Grüße,
Jan
machine-translated from German · Show original