martin_fuerst
6 July 2026 14:0706.07.2026 14:07
Hello,
Since the (self-performed) controller update of my L200V8
It starts very jerkily, then pauses for about 10 seconds.
to run at 2700 RPM and then slowly and gently
to reach the target speed.
All updates and a new setup have been performed.
Changing parameters doesn't achieve much, except for...
More abrupt acceleration from 0.
Once it reaches the correct RPM, it flies great.
Perhaps I overlooked something?
I've attached a picture with the serial number.
LG
Martin
Edited twice. Last edited on 06/07/2026 at 14:40 by martin_fuerst.
Hallo,
Seit dem (selbst durchgeführtem) Regler-Update meines L200V8
läuft er sehr ruckartig an, um danach ca. 10 Sekunden auf
2700U/Min zu laufen um dann langsam und sanft
auf Solldrehzahl zu gehen.
Alle Updates und auch neues Setup wurde gemacht.
Parameter verstellen bringt nicht viel, bis auf nur
ruckartigeres Anlaufen von 0 weg.
Hat er mal die Drehzahl erreicht, fliegt er klasse.
Ev. hab ich etwas übersehen?
Ein Bild mit Seriennummer hänge ich mal an.
LG
Martin
2 mal bearbeitet. Zuletzt am 06.07.2026 14:40 von martin_fuerst.
HeliALEX
7 July 2026 08:1907.07.2026 08:19
Hi Martin,
What is the value set for the ramp-up limit?
Is the RPM signal cable plugged back into the stabilizer's RPM port? Please check the controller status to see if the RPM value is displayed when the helicopter is on the ground.
The transmitter's main screen only displays the telemetry RPM value, not the signal from the RPM port.
Hallo Martin,
auf welchem Wert steht das Hochlauf-Limit?
Ist das Drehzahl-Signal Kabel wieder auf dem RPM Port der Stabi eingesteckt? Bitte mal im Regler Status schauen, ob der Drehzahl-Wert dort angezeigt wird, wenn der Heli am Boden läuft.
Auf dem Hauptbildschirm des Senders wird nur der Telemetrie- Drehzahlwert angezeigt, nicht das Signal vom RPM Port.
martin_fuerst
7 July 2026 08:3107.07.2026 08:31
Hi Alex,
Ramp-up limit currently set at 4
Thanks for the input - all cables are plugged in
I will check the speed value in the controller status.
What I noticed:
"ESC FW new LOGO 200" - Eddi's setup has different values:
Flight values speed controller
Lower control limit ----- ----- 16 ----- -----
Startup limiter ----- ----- 10 ----- -----
Base gas 40 50 60 50
Pitch Gas Addition 10 10 10 10
Cyclic gas addition 5 5 5 7
--------
My newly loaded (new setup/new Mikado etc.)
Lower control limit ----- ----- 30 ----- -----
Startup limiter ----- ----- 4 ----- -----
Base gas 50 55 60 50
Pitch Gas Addition 15 15 15 15
Cyclic gas addition 5 5 5 5
I need to test the values and lower the "lower control limit".
I'll join you later.
LG
Martin
Edited once. Last edited on 07/07/2026 at 08:33 by martin_fuerst.
Hallo Alex,
Hochlauflimit derzeit auf 4
Danke für Input - alle Kabel angesteckt
Drehzahlwert im Reglerstatus werde ich prüfen.
Was mir aufgefallen ist:
"ESC FW neu LOGO 200" - Setup von Eddi hat andere Werte:
Flugwerte Drehzahlregler
Untere Regelgrenze ----- ----- 16 ----- -----
Hochlauf Begrenzer ----- ----- 10 ----- -----
Basisgas 40 50 60 50
Pitch Gaszugabe 10 10 10 10
Zyklische Gaszugabe 5 5 5 7
--------
Mein neu geladenens (neues Setup/Mikado neu u.s.w.)
Untere Regelgrenze ----- ----- 30 ----- -----
Hochlauf Begrenzer ----- ----- 4 ----- -----
Basisgas 50 55 60 50
Pitch Gaszugabe 15 15 15 15
Zyklische Gaszugabe 5 5 5 5
Muss ich mal die Werte testen - und "untere Regelgrenze" absenken.
Komme erst später dazu.
LG
Martin
1 mal bearbeitet. Zuletzt am 07.07.2026 08:33 von martin_fuerst.
Eddi E. aus G.
7 July 2026 08:5207.07.2026 08:52
Good morning,
I'm a bit lost right now... the setup I received should, according to my understanding, actually be 'the' setup.
But I've since heard that there was further communication behind the scenes, and that something new was coming.
It's good to know that when the time comes, you can simply write down your trim and autotrim values, update the transmitter (so that the new setup is included), load it onto the 200, adjust the trim values again, and you're good to go.
But... with the current setup, I can't really understand the startup issue...?
In the end, Alex and Marik probably have the most experience with this, so I'm following along with interest :-)
—Eddi
Born to fly ...
forced to work.
Moin,
ich bin gerade etwas Lost ... das Setup was ich bekommen habe sollte dem Verständnis nach eingentlich 'das' Setup sein.
Aber inzwischen habe ich gehört, dass es da noch Kommunikation im Hintergrund gab, und dass nochmal was neues kommen sollte.
Gut zu wissen, wenn's dann soweit ist, kann man einfach seine Trim- und Autotrim-Werte rausschrieben, den Sender updaten (damit das neue Setup drin ist), das auf den 200-er laden, die Trim-Werte wieder eindrehen, und gut.
Aber ... mit dem Setup wie's gerade ist kann ich das mit dem Hochlauf nicht wirklich nachvollziehen ..?
Am Ende sind Alex und Marik vermutlich die mit der meisten Erfahrung damit, in sofern lese ich hier auch gespannt mit :-)
—Eddi
Born to fly ...
forced to work.
martin_fuerst
7 July 2026 08:5507.07.2026 08:55
Aha,
With a lower controller limit of 16-20 and a ramp-up limit of approximately 10
It will now proceed as usual.
It fits - for whatever reason :-)
Aha,
Mit unterer Reglergrenze 16-20 und Hochlauflimit ca 10
geht es nun wie immer.
Passt - warum auch immer :-)